Baby Lock Ovation Bedienungsanleitung

22 Serger Accessory/Feet Kit Instructions

www.babylock.com

MACHINE SETTINGS

Stitch type: 3-Thread Rolled Hem

Stitch selector: D

Needle: 02

Stitch width: M

Stitch length: 3-4 Rolled Hem

Upper knife: Engaged “UNLOCKED”

Differential feed: N-0.6

Sewing speed: Slow to moderate speed

1. Remove the left needle from the machine. Set machine to

narrow rolled hem (Refer to your instruction manual for

details).

2. Replace the standard presser foot with the beading foot.

3. Set stitch length setting at 3-4 mm according to the size of

beads used.

4. Position beads into beading foot as illustrated below.

5. Place edge of fabric you are attaching the beads to under

the presser foot, lower presser foot, and stitch.

NOTE: It is recommended to sew a test sample before

sewing your actual garment to determine the correct stitch

length.

Serge pearls, piping, cording, and more to the edge of fabric

with ease and speed. This one-step foot will give all of your

surface embellishments a professional ﬁnish.

Beading Foot

(BLE8-BF)

Instructions

www.babylock.com

Easily create straps, drawstrings, decorative trim, purse

handles and of course, belt loops. This binder takes all of the

work out of bias strips by folding and pressing them for you.

Choose from 3/4” or 1-1/2” sizes.

MACHINE SETTINGS

Stitch type: Triple Cover Stitch C1-C2-C3

Wide Cover Stitch C1-C3

(This is not a good application for chain

or narrow cover stitches)

Sewing speed: Moderate to slow

Fabrics used: Lightweight woven fabrics cut on the bias

Stitch length: 3-4

Cutting blade: Disengaged “LOCKED”

Upper looper: Down

Sewing table: On

Instructions:

1. Cut bias fabric strips:

3/4 inch Folder - Cut to 7/8 inch wide (22mm)

1-1/2 inch Folder - Cut to 1-5/8 inch wide (37mm)

Note: The strips must be cut this width even though it is

wider than the attachment measurements.

2. Feed bias strip, with right side facing up, into the

attachment.

3. Pull bias through and up to the needles and under the

presser foot.

4. Turn the handwheel 3-4 times to secure the stitch in the

fabric.

Belt Loop Binder

3/4 inch (19mm) (BLE8-S12)

1-1/2 inch (38mm) (BLE8-S11)

Instructions

Note: When using BLCS-2 or BLCS the accessory adaptor

BLCS-AA is needed.

5. Align the attachment with the needle position to ensure the

folded fabric is caught in the stitching. Make sure the stitch

is centered in the belt looping.

6. Be sure to allow 3 inches of extra bias strip at the beginning

and ending of project. The extra will be trimmed away

when ﬁnishing the project.

7. It is best to test sew before attaching the bias to the project.

Looking for a quick, easy way to make your hems invisible?

This foot was designed speciﬁcally for easily stitching a

blindhem on the serger. You can also use this foot for quick

stitching along fabric edges.

MACHINE SETTINGS

Needle: 02

Upper knife: Engaged “UNLOCKED”

Stitch type: 2-Thread Narrow Hem

Stitch selector: B

Stitch width: 5.0 mm

Stitch length: 3.5

Differential feed: N (N-0.6 for ﬁner fabrics)

Instructions:

1. For hemming, fold fabric as shown in diagram.

2. Place garment with wrong side up under the presser foot.

Before you begin serging, check the needle dropping

position. The needle should just catch the fold of the

fabric.

3. Once the needle dropping position has been determined,

set the adjustable guide on the foot to the fold edge of the

fabric. Move the adjustable guide by loosening the screw

on top of the foot and adjusting the plate right or left.

Then retighten the screw.

Blindhem Foot

(BLE8-BLHF)

Instructions

www.babylock.com

Use this foot for better visibility when attaching ribbon and lace,

or guiding lightweight decorative stitching. The raised guidelines

on the foot ensure that you stitch with accuracy. This foot is

perfect for decorative construction and the Baby Lock exclusive

Wave Stitch.

MACHINE SETTINGS

Any stitching application can be used (select one and check with

instruction book for length and width setting for speciﬁc stitch

selection).

1. Cut all threads to 4 inches (10 cm) in length.

2. Place fabric under the presser foot directly below the needles.

3. Lower the presser foot.

4. Turn the handwheel toward you to form 2 or 3 stitches.

5. Start to sew slowly.

6. After the ﬁrst few stitches, stop and cut excess threads.

7. Start the next seam at the toe of the presser foot.

Note: You only need to raise and lower the presser foot when

working with thick fabrics or when precise positioning is required.

Be careful not to push or pull the fabric. The serger will feed it

evenly without help.

Clear Foot

(BLE8-CLF)

Instructions

Needle

position

guide

Tape slot

www.babylock.com

Use the Cover/Chain Stitch foot for better visibility and easier

control for stitching curves or turning tight corners and

attaching tape and ribbons.

MACHINE SETTINGS:

Stitch: Left, right or center chain stitch, narrow, wide or triple

cover stitch. (Select one and check with instruction book for

length and width setting for speciﬁc stitch selection.)

Stitch Length: 3 to 4

Ribbon or tape: Up to 8mm wide

INSTRUCTIONS:

1. Snap on the Chain/Cover Stitch foot and set up the machine

for the stitch you desire.

2. Raise the presser foot.

3. Place fabric under the foot.

4. If using the ribbon or tape slot in the front of the foot, insert

ribbon into the slot and under the foot.

Note: The slot in the front of the foot is 7mm wide and will

accommodate up to an 8mm wide ribbon or tape. Ribbons or

tapes wider than 8mm are not recommended as they will not

ﬂow smoothly and will not lie ﬂat when stitched.

Cover/Chain Stitch

Foot

(BLE8-CCF)

www.babylock.com

5. Lower the presser foot.

6. Turn the handwheel toward you to form

2 or 3 stitches.

7. Start to sew slowly.

8. After the ﬁrst few stitches, stop and cut

excess threads.

9. Start the next seam at the toe of the presser foot.

10. Test sew sample for desired effect. Be careful not

to push or pull the fabric. The serger will feed it

evenly without help.

Note: This foot is not recommended for stitching

over heavy or bulky areas such as seam allowances

on mid-heavy weight polar ﬂeece. It is recommended

that seam allowances are clipped or trimmed to

remove excess bulk before using this foot over such

areas.

The Curve Foot is short and has a ﬂat sole, making it a good

choice for stitching curves and sewing over cross seams. Its

short size is also good for sewing around cuffs, necklines and

children’s wear using the cover stitches.

MACHINE SETTINGS:

1. Raise the presser foot lever.

2. Lower the cutting blade.

3. Raise the needles to the highest position.

4. Push the presser foot release lever located at the back of the

presser foot holder.

5. Carefully turn the presser foot clockwise 90 degrees.

6. Slide the presser foot to the rear to remove.

TO REPLACE THE PRESSER FOOT:

1. Raise the presser foot lever.

2. Lower the cutting blade.

3. Raise the needles to the highest position.

4. Slide the foot from the left to right.

5. Align the bar of the foot with the groove in the holder.

6. Lower the presser foot lever to snap into place.

Most stitching applications can be used (select one and check

with instruction book for length and width setting for speciﬁc stitch

selection). However, the Curving Foot does not work using the

differential feed while serging since the foot does not contact the

feed dogs completely. Also, this foot will not produce chain-off

using the chain stitch.

TO RELEASE THE PRESSER FOOT:

Curving Foot

(BLE8-CVF)

Instructions

www.babylock.com

This conventional binder will double fold and sew bias

strips to your project in one quick step, using either a chain

or coverstitch. Choose from two widths based on your

preference.

MACHINE SETTINGS

Stitch type: 1-1/2” Chain Stitch - C3 Needle Position C2-C3

Narrow Right Cover Stitch C2-C3

Stitch type: 1-1/8” Narrow Right Cover Stitch

Chain Stitch - C3 Needle

Stitch length: 3-4

Upper looper: Down

Upper knife: Disengaged “LOCKED”

Sewing table: On

Bias Strip Cut Size:

1-1/8 inch Binder:

• Cut 1-1/8 inch bias from ne fabrics such as calico, muslin,

etc.

• Cut 1 inch wide for medium weight fabrics such as trigger,

lightweight denim.

1-1/2 inch Binder:

• Cut 1-3/8 inch for ne fabrics such as calico, muslin, etc.

• Cut 1-1/4 inch wide for medium weight fabrics such as

trigger, lightweight denim.

Note: Test with fabric strip to make sure of correct width of

bias.

Note: When using BLCS-2 or BLCS the accessory adaptor

BLCS-AA is needed.

Double Fold Bias

Binder

1-1/8 inch (28mm) (BLE8-S3)

1-1/2 inch (36mm) (BLE8-S2)

Instructions

Instructions:

1. Secure attachment to table with guide ﬁxing screws.

2. Cut fabric strips to size needed.

3. Raise presser foot. With the point of the bias strip,

place strip into attachment. Use tweezers to feed the

strip into the attachment.

4. Place the folded bias up to the needles and under

the presser foot.

5. Turn the handwheel 3-4 times to secure the stitching

in the fabric.

6. Place the fabric that is to be bound into the slot of

the attachment. Place in the folded bias in front of

the presser foot.

7. Loosen the guide ﬁxing screws and move the

attachment right or left to align the attachment with

the needle position.

8. Sew test for proper alignment before sewing on

project.

INSTRUCTIONS FOR ELASTIC FOOT:

1. Before attaching the elastic foot to the machine,

loosen the elastic pressure adjustment screw, raise the

pressure plate and insert the elastic until it reaches

behind the foot (see illustration). Tighten the elastic

pressure adjustment screw slightly.

Note: The lines on the screw are for elastic tension

reference on future projects.

2. Replace the standard foot on the machine with the

elastic foot and elastic.

3. While stitching elastic onto your test fabric, adjust

the elastic pressure adjustment screw until the desired

effect is achieved.

Note: To insert elastic while elastic foot is on machine,

raise presser foot. Loosen elastic pressure adjustment

screw, raise the pressure plate and insert elastic until

it touches the needle. Stitch until the elastic passes the

needle. Position fabric and then adjust pressure screw as

needed.

Elastic Foot

(BLE8-EF)

Instructions

Conﬁdently serge elastic by letting this foot take care of all

the work. This foot provides even pressure on the elastic

every time to prevent pulling and tugging on the needles. The

adjustable guide and tension dial allow you to serge elastic

with a ﬁnished uniform stretch. The guide holes provide

control for projects requiring ﬁshing line. ATTACHING ELASTIC USING THE ELASTIC FOOT:

MACHINE SETTINGS

Stitch type: 4-Thread Overlock

Needle: 01and 02

Stitch width: M-7.5

Stitch length: 4.0

Upper knife: Engaged “UNLOCKED”

Differential feed: 0.5

Sewing speed: Slow speed

1. Insert elastic into elastic foot (see instructions for elastic foot).

2. Set up machine according to above chart.

3. Slightly raise the pressure plate of the foot and insert elastic

between the plate and lower support bar until the edge of

elastic reaches the feed teeth. (It may be necessary to loosen

the elastic pressure adjustment screw to feed the elastic

through.)

4. Loosen the screw on the adjustable tape guide to

accommodate the width of your elastic. Then re-tighten the

screw.

5. Sew the elastic for about an inch or so to ensure it is feeding

properly.

6. Place the fabric under the foot and sew elastic to fabric.

7. Adjust the elastic pressure adjustment screw so that the

desired ﬁnish can be obtained.

a. Tighter tension on the elastic gives more elasticity of the

fabric after it is sewn.

b. Looser tension on the elastic gives less elasticity of the

fabric.

www.babylock.com

COVERSTITCH:

MACHINE SETTINGS

Stitch type: Triple Cover Stitch or Wide Cover Stitch

Needles: Triple Cover Stitch-C1,C2,C3 Wide

Cover Stitch-C1,C3

Stitch length: 4

Stitch width: M

Differential feed: Normal

Upper knife: Disengaged “LOCKED”

Sewing table: Remove knife cover and snap on sewing

table

Sewing speed: Slow

INSERTING FISHING LINE USING THE ELASTIC FOOT:

MACHINE SETTINGS

Stitch type: 3-Thread Rolled Hem

Needle: 02

Stitch selector: D

Stitch width: 5.0

Stitch length: 1.5R (Rolled hem setting)

Differential feed: 0.6

Upper knife: Engaged "Unlocked"

Sewing speed: Slow

1. Thread your serger for a 3-thread rolled edge using

decorative threads in the upper looper.

2. Slide the ﬁshline through the guide holes on the right side of

the elastic foot and then under the back of the foot leaving a

3" to 4" tail in the back.

3. Snap the foot on the machine and place the fabric under the

foot with the ﬁshline to the right of the needle.

4. Begin serging making sure the ﬁshline is caught in the

stitching as the edge is being rolled.

5. When you have ﬁnished serging, carefully remove the fabric

and ﬁshline from under the presser foot being careful not to

pull the ﬁshline out of the seam.

elastic tape

tension adjuster screw

Elastic Foot

(BLE8-EF)

Instructions (continued)

Andere Handbücher für Ovation

Inhaltsverzeichnis

Andere Baby Lock Nähmaschine Handbücher

Baby Lock

Baby Lock Crafter's Choice BLCC2 Technisches Handbuch

Baby Lock

Baby Lock Cover Stitch BLCS-2 Technisches Handbuch

Baby Lock

Baby Lock evolve Bedienungsanleitung

Baby Lock

Baby Lock BL-5180 Bedienungsanleitung

Baby Lock

Baby Lock SOLARIS BLSAU3 Bedienungsanleitung

Baby Lock

Baby Lock Ellisimo GOLD BLSOG Technisches Handbuch

Baby Lock

Baby Lock Celebrate BLS1 Technisches Handbuch

Baby Lock

Baby Lock Creative Pro Installationsanleitung

Baby Lock

Baby Lock Diana BL480A Technisches Handbuch

Baby Lock

Baby Lock Pro-Stitcher Lite BLPS-LITEG-VF Bedienungsanleitung

Baby Lock

Baby Lock Valiant BMV10 Bedienungsanleitung

Baby Lock

Baby Lock Flourish BLMFO Bedienungsanleitung

Baby Lock

Baby Lock Anna BL20A Montageanleitung

Baby Lock

Baby Lock Regalia BLRG20 Bedienungsanleitung

Baby Lock

Baby Lock Enlighten BLE3ATW-2 Technisches Handbuch

Baby Lock

Baby Lock Coronet BLCT16A Technisches Handbuch

Baby Lock

Baby Lock Embroidery Professional PLUS BMP9 Bedienungsanleitung

Baby Lock

Baby Lock Crown Jevel Konfigurationshandbuch

Baby Lock

Baby Lock Sofia BL137A2 Technisches Handbuch

Baby Lock

Baby Lock Pro-Stitcher BLPS Technisches Handbuch

Baby Lock

Baby Lock Soprano BLMSP Technisches Handbuch

Baby Lock

Baby Lock Tiara BLTR16 Technisches Handbuch

Baby Lock

Baby Lock Model BLCS Bedienungsanleitung

Baby Lock

Baby Lock Evolution BLE8W-2 Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Singer

Singer 2517 Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Janome

Janome Quilt Maker Pro 18 VERSA Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung