Baby Lock Pearl BLQF Bedienungsanleitung

Table of Contents

Page

3. Parts & Hardware List

6. Step 1- Remove Track Supports

7. Step 2- Table Assembly

8. Step 3- End Leg Assembly

11. Step 4- Middle Leg Assembly

13. Step 5- Rotate the Frame

14. Step 6- Support Rail Assembly

15. Step 7- Track Assembly

18. Step 8- Ratchet Stop Assembly

20. Step 9- Pole Bracket Assembly

21. Step 10- Pole Coupler Assembly

22. Step 11- Pole End Assembly

25. Step 12- Batting Bar Bracket Assembly

26. Step 13- Pole to Frame Assembly

26. Step 14- Rubber End Cap Assembly

27. Step 15- Bungee Clamp Assembly

27. Step 16- Hook & Loop Tape on Pole Assemblies

28. Step 17- Attach Leaders

28. Step 18- Adjusting Frame Height and Leveling

Baby Lock Pearl Frame

What’s Included

Your Baby Lock Pearl Frame is delivered in three

separate boxes. Upon opening, please check

immediately to see if you have received the

items listed in the Parts and Hardware lists found

on pages 3, 4 and 5. In addition, the following

items will be found in Box 2:

1. Baby Lock Pearl Frame Assembly Instructions

2. (3) Hook and loop tapes to attach leaders to

poles

Baby Lock Leaders (Part # BLQL) are sold

separately.

Pole Section, 5’

(8)

Pole Coupler

(4)

Baby Lock Pearl Frame Parts & Hardware List

Left Pole

Bracket

Assembly (1)

Support Rail (2) Table Section with Plastic Top

5’ (2)

M6 x 12mm

Socketed Washer Head

Cap Screw[ Track Support

Screws (12)

(Comes in track supports

on table sections)

Track Support, 5’ (4)

(Comes on table sections)

Table Splice (2) Track Support Coupler (2)

M5 x 8mm

Socketed Button Head Cap

Screw: Track Support Coupler

Screws (12)

Track, Black, 10’ (4)

Lower End Leg (2) Upper End

Leg A (2)

Upper End

Leg B (2)

Nylon Washer for Height

Adjustment (10) 5 extra

Right Pole Bracket

Assembly (1)

(Comes with latches

not assembled)

QF05300-100

QF05300-200

QF05300-701 QF09318-702

QF05300-05 QF09318-03 QF05300-150 QF05300-300

QF09318-303

QF05300-02

QF09318-304

QF05300-04

QF05300-401

QF05300-402 QF05300-403 QF05300-157

Bungee Clamps (4)

Lower Middle Leg (1)

Upper Middle Leg (1)

Batting Bar Bracket Assembly

(w/clamp) (2)

M6 x 25mm

Socketed Washer Head Cap

Screw: Batting Bar Bracket

Screws (8)

M8x25mm

Socketed Button Head Cap

Screw (For thick metal on

support rail) (12)

Nut, M8 Nylon Lock (4)

Metal Washer, M8 (5) 1 extra

M8x16mm

Socketed Button Head Cap

Screw (31) 2 extra

Leveling Glide (6)

QF09318-103

BUNGEE HOLDER BUNGEE HOLDER COVER

QF09318-104

BUNGEE HOLDER SPACER

QF09318-103

RATCHET STOP

QF09318-203

RATCHET STOP HOLDER

QF09318-205

RATCHET STOP BUSHING

QF09318-201

CONNECTOR BOLT

QF09318-204

QF09318-202

RATCHET STOP MOUNT

RAIL BEARING SNAP

QF09318-105

RAIL BEARING SNAP COVER

QF09318-106

Fig. 10-2

QF09318-105

QF09318-703

OUTSIDE POLE END V-GROOVE BEARING

QF09318-705 QF09318-713

HAND WHEEL COLLAR

QF09318-714

STEEL SNAPPING BUTTON/LOCKING CLIP

LEVELING FOOT

M6 x 48mm

Socketed Washer Head Cap

Screw: Ratchet Stop Screw (3)

Ratchet Stop Bushing (3) Ratchet Stop Mount (3)

Ratchet-Stop Holder (3)

Ratchet Stop (3)

Baby Lock Pearl Frame Parts & Hardware List

Batting Bar Bracket Clamp (2)

QF05300-602 QF05300-601 QF09318-108 QF09318-110

QF09318-203 QF09318-201 QF09318-205 QF09318-202

QF09318-204 QF09318-06

QF09318-09 QF09318-08

QF05300-460

QF05300-465

QF05300-113

QF09318-07

Leg End Cap Come

Preinstalled in Legs (6)

QF09318-406

Large Washer for Knob (2)

QF05300-155

Knob (2)

QF05300-152

5mm Allen Wrench (1)

Pole End Assembly with Short

Bolt (2)

Pole End Assembly with Long

Bolt (1)

4mm Allen Wrench (1)

HAND WHEEL ASSY

QF09318-720

SHORT BOLT RATCHET WHEEL

QF09318-730 QF09318-730

LONG BOLT RATCHET WHEEL

HAND WHEEL ASSY

QF09318-720

SHORT BOLT RATCHET WHEEL

QF09318-730 QF09318-730

LONG BOLT RATCHET WHEEL

HAND WHEEL ASSY

QF09318-720

SHORT BOLT RATCHET WHEEL

QF09318-730 QF09318-730

LONG BOLT RATCHET WHEEL

3mm Allen Wrench (1)

Hand Wheel Insert (1)

(May be inside Hand Wheel)

Hand Wheel Assembly (1)

V-Groove Bearing (8)

(Comes on pole end and

ratchet assemblies)

Rubber Thread Caps (8) Regular Nut, M10, Assembly

Tool (1) (To aid with pole end

assembly, see note in Step

11-4 page 22)

Hook & Loop Tape, 10’

for poles (3)

Assembly Instructions (1)

Baby Lock Pearl Frame Parts & Hardware List

Not Shown Not Shown

Pole End Assembly (5)

Fig. 9-1 Fig. 9-2

Fig. 8-1

Fig. 9-4

Fig. 9-3

17/13/16mm Wrench (1)

QF09326 QF09320 QF09321

QF09325

QF09318-705

QF09318-716

QF09318-717

QF09318-713

QF09318-111 QF09318-112 QF09318-113 QF09318-114

QF00665 BLQFAI

Step 1: Remove Track Supports

Parts needed

2-Table Section

Tools Required

4mm Allen Wrench (Provided)

NOTE: The track support nish could be

damaged if not protected or if placed onto a

rough surface. Handle with care.

1-1: Place the table sections with the track

supports face down onto a protective surface.

(Fig. 1-1)

NOTE: When removing the track supports,

keep them in the same position and orientation

to ensure perfect alignment when they are

replaced.

Step 1

Remove Track Supports

Fig. 1-1

1-2: Using the 4mm Allen wrench remove the

three screws from each track support and set

the track support aside in a safe place

(Fig. 1-2). Leave the table sections face down

for Step 2-1.

Fig. 1-2

Step 2: Table Assembly

Parts needed

2-Table Section

2-Table Splice

12- M8x16mm Socketed Button Head Cap

Screw QF09318-07

Tools Required

5mm Allen Wrench (provided)

2-1: With the table sections face down (large

round screw holes for track supports up), slide

the two table sections together end to end, as

close as possible. Place a table splice onto the

sections as shown in Fig. 2-1, lining up the

holes in the splice with those in the sections.

Repeat with remaining table splice on the

opposite side of the table sections.

2-2: Place four (4) M8x16mm QF09318-07

through the side of each table splice and nger-

tighten them into the table sections. (Fig. 2-1)

2-3: Finger-tighten two (2) M8x16mm

QF09318-07 through the top of each table

splice.

2-4: Pull the two (2) table sections as close

together as possible to remove gap.

2-5: Using the 5mm Allen wrench, tighten the

four side screws on each table splice, until the

splice touches the side of the table section,

and then loosen the screws ½ turn.

2-6: Using the 5mm Allen wrench, tighten fully

the two (2) top screws on each table splice.

Finally, fully tighten the four (4) side screws on

each table splice. (Fig. 2-2)

Step 2

Table Assembly

Fig. 2-1

Fig. 2-2

Step 3: End Leg Assembly

Parts needed

1-Table Assembly

2-Upper End Leg A

2-Upper EndLeg B

2-Lower End Leg

4-Leveling Glide

12-M8x16mm Socketed Button Head Cap Screw

QF09318-07

8-M8x25mm Socketed Button Head Cap Screw

QF09318-06

4-Nylon Washer

Tools Required

5mm Allen Wrench (provided)

3-1: With the table on the protective surface,

still facing down, position the upper end legs A

& B so the height adjustment holes face each

other across the short end of the table. (See

Fig. 3-1 and Detail 3.1.)

Step 3

End Leg Assembly

3-2: Attach each upper end leg to the table

with two (2) M8x16mm screws through the

upper corner leg brackets at front or rear and

with two (2) M8x24mm at the end. Lightly

tighten for now with the 5mm Allen wrench.

Fig. 3-1

Fig. 3-2

Detail 3-1

Height-Adjustment

Holes

Upper

End

Leg A

Upper

End

Leg A

Upper

End

Leg B

Upper

End

Leg B

M8x16mm QF09318-07

front and rear

M8x25mm

QF09318-06

at end

Fig. 3-3

Detail 3-3

Step 3

End Leg Assembly (continued)

3-3: Slide one (1) lower corner leg onto the

two (2) upper corner legs on each end of the

frame as shown in Fig. 3-2 on the previous

page and Fig. 3-3. Choose the preferred height

of the frame based on the table in Fig. 3-4.

Place an M8x16mm screw with nylon washer

into the same height setting on each of the

corner legs. The purpose of the nylon washer is

to protect the paint, in case the height setting

is changed later.

Fully tighten the screw on each leg with the

5mm Allen wrench. (Detail 3-3)

Fig. 3-4

Table of Heights

Fig. 3-5

Step 3

Corner Leg Assembly (continued)

Detail 3-4

3-4: Thread a leveling glide into each end of

the corner leg assemblies, leaving about 1/2” of

the threads exposed to make it easier to level

the frame later. (Fig. 3-5 and Detail 3-5)

Detail 3-5

Inhaltsverzeichnis

Andere Baby Lock Nähmaschine Handbücher

Baby Lock

Baby Lock Tiara BLTR16 Technisches Handbuch

Baby Lock

Baby Lock Jazz BLMJZ Technisches Handbuch

Baby Lock

Baby Lock Tempo BLTP Bedienungsanleitung

Baby Lock

Baby Lock ellegante BLG guid Technisches Handbuch

Baby Lock

Baby Lock Embroidery Professional BMP8 Bedienungsanleitung

Baby Lock

Baby Lock A-LINES Sofia BL137A Technisches Handbuch

Baby Lock

Baby Lock esante BLN Bedienungsanleitung

Baby Lock

Baby Lock Regent BLRT18 Technisches Handbuch

Baby Lock

Baby Lock Endurance II BND9-2 Bedienungsanleitung

Baby Lock

Baby Lock Valiant BMV10 Bedienungsanleitung

Baby Lock

Baby Lock Ellageo BLL Bedienungsanleitung

Baby Lock

Baby Lock Flourish BLMFO Bedienungsanleitung

Baby Lock

Baby Lock ellure plus BLR2 Bedienungsanleitung

Baby Lock

Baby Lock Enterprise Installationsanleitung

Baby Lock

Baby Lock Ellisimo BLSO Bedienungsanleitung

Baby Lock

Baby Lock imagine BLE1AT-2 Bedienungsanleitung

Baby Lock

Baby Lock Urity BLTY Technisches Handbuch

Baby Lock

Baby Lock Embroidery Professional PLUS BMP9 Bedienungsanleitung

Baby Lock

Baby Lock Creative Pro Konfigurationshandbuch

Baby Lock

Baby Lock Ellageo PLUS BLL2 Technisches Handbuch

Baby Lock

Baby Lock Altair BLTA Installationsanleitung

Baby Lock

Baby Lock Quilter's Choice BLQC2 Technisches Handbuch

Baby Lock

Baby Lock Imagine Bedienungsanleitung

Baby Lock

Baby Lock Elizabeth BL200A Technisches Handbuch

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Singer

Singer 2517 Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Janome

Janome Quilt Maker Pro 18 VERSA Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung