5
Always unplug the appliance before cleaning.
Clean the appliance, food pouches, and easy fill funnels before and after use.
Bowl, Blade and Bowl Lid are top shelf dishwasher safe* and can also be hand washed with warm,
soapy water. Never use abrasive pads to clean machine parts.
Stainless steel heating plate can be scrubbed with abrasive pad to remove mineral scaling.
Never put the Driveshaft in the dishwasher.
Base and Driveshaft should be wiped with damp cloth only.
We recommend regular cleaning of the Steam Tank to prevent damage to the machine from mineral
deposits. The frequency of cleaning will depend on the type of water you are using and how much
mineral deposit build up forms. Always unplug before cleaning. Put 1/3 cup white vinegar and 1/3
cup distilled water in machine and let sit overnight. Pour out vinegar and water solution following
instructions below. Refill Steam Tank with purified water, plug in machine and run “Steam” cycle for
15 minutes. Rinse with purified water to eliminate any remaining vinegar taste. Empty any remaining
water and refill with purified water before steaming new recipes.
Never use a chemical descaler in the machine.
Note: To remove unwanted water from the steam tank, water tank, or lid, see diagram below.
Any other servicing should be performed by an authorized service representative.
The food pouch and easy-fill funnel are top rack, dishwasher safe.
Thoroughly rinse out the food pouch with soap and water.
Do not use harsh abrasives to clean the food pouch or easy-fill funnel.
Allow parts to dry before storing away.
6
Cleaning
Cleaning the Food Pouch
Driveshaft
Knob
Remove driveshaft from bowl before cleaning in
dishwasher. See illustration.
To remove Driveshaft, turn Knob on bottom
of bowl counter-clockwise and pull out. Wipe
drive shaft with damp cloth. Never put driveshaft in
dishwasher. Do not misplace Driveshaft Gasket
while cleaning. To replace the Driveshaft after cleaning, insert into
hole in bottom of bowl and turn clockwise to lock in place *.
*Always make sure Driveshaft & Driveshaft Gaskets are properly
inserted and locked into place to prevent damage to bowl & base.
Removing and Replacing the Driveshaft
Carefully tilt the
machine backward
to empty any
remaining water.
Remove the water tank
knob and carefully
empty any excess water.
If water gets
trapped inside
lid after washing,
tilt lid to use
the drain holes
located on the
top to empty out any
remaining water.
Troubleshooting
Condition Possible Cause Possible Remedy
Machine will
not start.
Machine
stops during
operation
Final puree
consistency
isn’t smooth
Can not remove
Blade from
Driveshaft
Scaling in
Steam Tank
Blade is in dropped position with driveshaft
pins locked in place.
Raw food isn’t diced finely enough before
steaming.
Low water content of raw food.
Mineral rich water used persistently. Clean Steam Tank by following instructions on
page 5.
Lock bowl back onto machine. Gently pull up on
center blade column while twisting
counter- clockwise.
Steam Tank is dry. (Machine will beep rapidly
5 times to indicate that the Steam Tank is Dry)
Steam Tank is dry. (Machine will beep rapidly
5 times to indicate that the Steam Tank is Dry)
Machine is unplugged. Plug in Baby Brezza.
Safety tab on Bowl Lid is not fully inserted
into Base.
Safety tab on Bowl Lid has
been disengaged from Base.
Make sure Bowl Lid is turned counter-clockwise
as far as possible and safety tab on Bowl Lid
is fully inserted into Base.
Make sure Bowl Lid is turned counter-clockwise
as far as possible and safety tab on Bowl Lid
is fully inserted into Base.
Add water to Water Tank.
Add water to Water Tank.
Dice food into smaller pieces, approximately
1/4”-1/2” (1cm), before placing in bowl.
Add additional water, formula, breast milk or
other liquid after steaming and blend longer.
If you can not remedy problems with the machine by using the troubleshooting chart
above, please contact Customer Service at 1-888-396-6552.
