Baicells Nova430 Bedienungsanleitung

Nova430

Outdoor 4x250mW eNodeB

Quick Guide

P/N: 1701000177

Document version: 01

1.Product Overview

Introduction1.1

Baicells Nova430 is an advanced two-carrier outdoor eNodeB based on LTE TDD

technology, which is developed by Baicells. It is capable of operating in Carrier

Aggregation (CA) or Dual Carrier (DC) mode / split mode.

In CA mode, contiguous or non-contiguous channels are aggregated to provide up to 40

MHz bandwidth. This essentially doubles the downlink capacity when the CA430 is used

with all CAT6/7 user equipment.

In DC mode, each carrier is treated as an independent cell, supporting 96+96 users, and

each supporting 5, 10, 15, or 20 MHz bandwidth. Using a Nova430 in DC mode

simplifies and streamlines the deployment of split sectors.

In addition to having the option to operate Nova430 in either CA or DC mode, HaloB (an

embedded MME option) comes as a default feature in the base software. Baicells's

patented HaloB solution migrates the necessary core network functions to the eNB.

Features1.2

Citizens Broadband Radio Service (CBRS) band covers with dual carrier.

Peak rate: (up to) DL 220Mbit/s, UL2x28 (56) Mbit/s with 2x20MHz spectrum, using

all Cat6/7 or higher UEs.

Support flexible uplink and downlink time slot ratio: 1(2:2), 2(1:3), and high speed

data transmission.

Support 5MHz/10MHz/15MHz/20MHz operation bandwidth.

96 concurrent users per carrier, 96+96 in DC mode.

Support copper (RJ-45) backhaul, flexible to deploy.

Integrated small cell form factor for quick and easy installation.

Suitable for private and public deployments; any IP based backhaul can be used,

including public transmission protected by Internet Protocol Security (IPSec).

Support PoE++ power supply, only one Ethernet cable required for data

transmission and power supply.

Security services to provide timely protection against potential security risks and

illegal intrusion.

Support simple and convenient local and remote web management.

Integration as required, easy to installation and deployment, accurate

coverage and improved network capacity.

Support network management functions, which includes the management,

monitoring and maintenance.

Appearance1.3

The Nova430 interfaces are described in Table 1-1.

Table 1-1 Nova430 Interface Description

Interface Name

Description

ETH/POE

RJ-45 interface (FE/GE)

Used for power supply, debug or data backhaul.

PoE++, complied with IEEE 802.3bt standard

GPS

GPS antenna interface, N type connector

ANT0

External antenna interface 1, N type connector

ANT1

External antenna interface 2, N type connector

ANT2

External antenna interface 3, N type connector

ANT3

External antenna interface 4, N type connector

The Nova430 interface indicators are described in Table 1-2.

Table 1-2 Nova430 Interface Indicators

Identity

Color

Status

Description

PWR

Green

Steady On

Power on

OFF

No power supply

CELL1

Green

OFF

CELL1 is in inactivated.

Identity

Color

Status

Description

Fast flash: 0.1s on,0.1s off

CELL1 is in deactivated.

Slow flash: 1s on,1s off

CELL1 is in activated.

CELL2

Green

OFF

CELL2 is in inactivated.

Fast flash: 0.1s on,0.1s off

CELL2 is in deactivated.

Slow flash: 1s on,1s off

CELL2 is in activated.

ALM

Red

Steady On

Hardware alarm

OFF

No alarm

Technical Specification1.4

1.4.1 Hardware Specification

Item

Description

LTE Mode

LTE TDD

LTE Frequency

Band48

Channel Bandwidth

5MHz, 10MHz, 15MHz, 20MHz per carrier

Output Power

24 dBm per antenna

Receive Sensitivity

-100 dBm

Synchronization

GPS

Backhaul

1 RJ-45 Ethernet interface (1 FE/GE)

MIMO

DL 2 x 2 on each carrier, 2 carriers

Dimension (HxWxD)

with joint: 381x 227 x 75 millimeters

without joint and handle: 311 x 227 x 75 millimeters

Installation Type

Pole or wall mount

Antenna Type

External high-gain antenna compatible with eNB N-Type

connectors

External GPS antenna, N-Type connector

Power Consumption

Typical 20W, MAX 25W

Power Supply

PoE++, comply with IEEE 802.3bt standard

Weight

4.75kgs (with pre-installed bracket)

4.35kgs (without bracket)

MTBF

≥ 150000 hours

MTTR

≤ 1 hour

NOTE: The test method of receiving sensitivity is proposed by the 3GPP TS 36.104, which is based on

5MHz bandwidth, FRC A1-3 in Annex A.1 (QPSK, R=1/3, 25RB) standard.

1.4.2 Global Part Numbers

Model No.

Description

pBS3101SE

Band42/43/48, 10MHz, 20MHz per carrier, DL 2 x 2 on

each carrier, 2 carriers.

1.4.3 Software Specification

Item

Description

LTE Standard

3GPP Release 15

Peak Rate

DC mode

2x20 MHz:

SA1: DL 2x80Mbps, UL 2x28Mbps

SA2: DL 2x110Mbps, UL 2x14Mbps

2x10MHz:

SA1: DL 2x40Mbps, UL 2x14Mbps

SA2: DL 2x55Mbps, UL 2x7Mbps

CAmode

2x20 MHz:

SA1: DL 160Mbps, UL 28Mbps

SA2: DL 220Mbps, UL 14Mbps

2x10MHz:

SA1: DL 80Mbps, UL 14Mbps

SA2: DL 110Mbps, UL 7Mbps

User Capacity

96 concurrent users in single carrier mode

96+96 concurrent users in DC mode

96 concurrent users in CA mode

QoS Control

3GPP standard Quality of Service Class Identifier (QCI),

SC1

Modulation

UL: QPSK, 16QAM, 64QAM

DL: QPSK, 16QAM, 64QAM

Voice Solution

VoLTE (future software release)

Traffic Offload

Local breakout

SON

Self-organizing network:

Automatic setup

Automatic Neighbor Relation (ANR)

PCI confliction detection

Network Mgmt.

TR-069,SNMP

Maintenance

Support remote/local maintenance, based on SSH protocol

Support online status management

Support performance statistics

Support failure management

Item

Description

Support configuration management

Support local or remote software upgrading and loading

Support log

Support connectivity diagnosis

Support automatic start and configuration

Support alarm reporting

Support user information tracing

Support signaling trace

1.4.4 Environment Specification

1.4.5 Regulatory Compliance

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

Item

Description

Operating Temperature

-40°C to 55°C

Storage Temperature

-50°C to 65°C

Humidity

5% to 95%

Atmospheric Pressure

70 kPa to 106 kPa

Ingress Protection Rating

IP65

Power Interface Lightning Protection

Differential mode: ±10KA

Common mode: ±20KA

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

50cm between the radiator & your body.

ISEDC Compliance

This device complies with Innovation, Science, and Economic Development

Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause u

ndesired operation of the device.

Le présent appareil est conforme aux CNR d' Innovation, Science et Développement

économique Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

The antenna(s) used for this transmitter must be installed to provide a separation

distance of at least 50cm from all persons and must not be collocated or operating in

conjunction with any other antenna or transmitter, End-Users must be provided with

transmitter operation conditions for satisfying RF exposure compliance.

Les antennes utilisées pour cet émetteur doivent être installées de façon à offrir une

distance de séparation d'au moins 50cm entre toutes les personnes et ne doivent pas

être colocalisées ou fonctionner conjointement avec d'autres antennes ou transmetteurs.

pour satisfaire la conformitéàl'exposition RF.

2.Installation

Installation Material2.1

In addition to industry standard tools, you will need the materials described in Table 2-1

during the installation. When selecting an RF antenna, be sure to match the frequency

range of the antenna with the eNB.

Table 2-1 Support Materials

Item

Description

Antenna RF cable

50 ohm feeder

Ethernet cable

Outdoor CAT6, shorter than 100 meters

Antenna

Omnidirectional, or directional antenna

Ground cable

The diameter of grounding cable must be 10mm2or greater.

Installation Tool2.2

Knife

Vise

Wrench

Cross screw driver

Tape measure

Percussion drill and

some drill heads

Cable vice

hammer

NOTE: Other accessories have been packed in the packing box.

Weatherproofing2.3

For RF antenna weatherproof, adopt cold shrink tubes.

To protect the connection points from weather and climate, clean each connection point

before installing cold shrink tubes, per the following figure.

1. Insert the cable into the cold shrink tube.

2. Tighten the connector.

3. Push the cold shrink tube to the top joint, and pull out the strip.

4. Ensure the cold shrink tube is tightly fitted with the connection.

For GPS antenna weatherproof, adopt all-weather electrical tape and mastic tape, per

the followed figure.

NOTE: Make sure that the wrapping direction of the last layer is from the bottom up. The last layer

should be tight enough to keep it from cracking.

Install GPS Antenna2.4

Read the following GPS antenna installation requirements before installing it on the eNB.

No major blocking from buildings in the vicinity. Make sure the space atop is at least

45 degrees unblocked by any buildings.

Avoid installing the GPS antenna in the vicinity of any other transmitting and

receiving devices, to avoid interference.

The GPS antenna should be installed within 45 degrees to the lightning rod.

The GPS antenna system includes an antenna and a connector. The two parts should be

assembled according to Figure 2-1.

Figure 2-1 Assemble GPS Antenna

After assembling the GPS antenna, the connector must be waterproofed by all-weather

electrical tape and mastic tape.

Install on Pole2.5

Check to ensure the diameter of the pole is in the range of 1.6 inches to 2.8 inches

(40mm to 70 mm). The position of the eNB on the pole should be at least 47 inches (120

cm) in height.

The brackets have been pre-assembled in manufacturing before packing. It includes two

parts, one is pre-assembled on the back of device. The other is for pole mounting or wall

mounting, as shown in Figure 2-2.

Inhaltsverzeichnis

Andere Baicells Drahtloser Zugangspunkt Handbücher

Baicells

Baicells Neutrino-224 Bedienungsanleitung

Baicells

Baicells EG7035E Bedienungsanleitung

Baicells

Baicells EG7035E-M1 Bedienungsanleitung

Baicells

Baicells EG7010A-M11 Bedienungsanleitung

Baicells

Baicells Atom ID0406-6.5 Bedienungsanleitung

Baicells

Baicells EG2030C-M2 Bedienungsanleitung

Baicells

Baicells ATOM OD06 Bedienungsanleitung

Baicells

Baicells Nova442i Bedienungsanleitung

Baicells

Baicells CW0100 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung