Balluff BNI EIP-502-105-Z015 Bedienungsanleitung

Distributed Modular I/O Quick Start Guide for 4 port IO-Link Master

Communication

Discrete I/O

Analog I/O

Outputs

Specialty

Power

Discrete

I/O

Analog

I/O

Valve Manifold

Control

RFID or

Specialty

Devices

Discrete

I/O

Quick Start Guide

BNI004A

BNI EIP-502-105-Z015

Connect the Distributed Modular I/O Master Block

11. Using an M12 D-coded EtherNet/IP cable, connect the block to the Ethernet network.

2. Power up the block using 24VDC and a 7/8" 4pole connector wired according to the below diagram.

3. Set the IP address of the block using the pushbutton display. For instructions on operating the display, see the manual.

Port 0

Port 1

Port 2

Port 3

Port 4

Port 5

Port 6

Port 7

IO-Link 1

IO-Link 2

IO-Link 3

IO-Link 4

Pin Function Description

1 TX + Transmit Data +

2 RX + Receive Data +

3 TX - Transmit Data -

4 RX - Receive Data -

M12 Network Port

Pin Function Description

1 + 24 V Actuator Supply

2 + 24 V Sensor/Bus Communication Supply

3 0 V Sensor/Bus Communication Supply

4 0 V Actuator Supply

7/8" Auxiliary Power Port

Pin Conﬁgurable Port IO-Link Port

1 + 24 V + 24 V

2 Input 2 or Output 2 Input/Output 2

3 0 V 0 V

4 Input 1 or Output 1 IO-Link or Input/Output 1

5 FE FE

M12 I/O Port

Network

Aux Power

Pushbutton Display

IP address subnet mask

gateway

00 01

1514

1110

06 07

0302

Tell the Controller About the Device

21. Every controller will need to know three things about the device being connected

over EtherNet/IP:

nThe IP address of the block

nWhere to look for the data (Instance ID) in the block

nHow much data is at the location (Data length)

2. Setup the block in the engineering software with the Instance ID and the Data

Length for the input data, the output data and the conﬁguration data.

Instance ID Data Length (Bytes)

Input 100 200

Output 101 134

Conﬁguration 102 98

Instance ID: where the data is located in the device, sometimes called the

assembly instance number.

Data length: how much data to expect at this location, these are 8bit, 1byte

short integers. For controllers that read in 2byte words or in individual bit

counts, please see the Balluff website for the data assistance spreadsheet.

Troubleshooting Tips:

nFor assistance with programming these values into a speciﬁc controller or

engineering software, please contact the controller manufacturer.

nSome controllers have a maximum data size below the 200 bytes required,

review the parameters of the controller before selecting.

nSome controllers are using a third party device (such as an Anybus gateway)

to communicate over EtherNet/IP. These devices typically require additional

software to conﬁgure and establish communication properly.

Using Electronic Data Sheet (EDS) Files

The EDS ﬁle in RSLogix5000 Ver 20

To make life easier for some engineering platforms the eds

ﬁles are available for download from networks.balluff.com

Conﬁrm Communication is Established

3It is important to conﬁrm the device is talking to the controller; this can be done by verifying status lights on the block just below the aux power ports

and just above the ﬁrst M12 I/O ports.

Troubleshooting Tips:

nSome controllers require a power cycle of the device or the controller or both before the communication is established.

nMake sure there are no IP Address conﬂicts between devices.

nEnsure that the devices are connected on the same LAN or hardwired network.

nEtherNet/IP DLR (Device Level Ring) capable devices ship with the default setting, DLR enabled. Some controllers may require that the device has

this functionality disabled before communication can be established.

Solid Green Solid green at 100Mbps, off if using 10Mbps

Intermittent ﬂashing orange

Functional

Communication

Is Established:

Depending on which

port has the cable

plugged into it, these

could be on or off

Conﬁgure IO-Link Ports for Distributed Modular I/O

4Once communication is established you now need to tell the device how it will be used for Distributed Modular I/O. Every port can be used for

standard I/O and is defaulted to this conﬁguration. To tell the master block to look for an IO-Link device, there are some conﬁguration bytes that must

be setup.

Description Byte Bit

76543210

For Standard I/O: 0x00

For IO-Link: 0x01

IO-Link 2 IO-Link 1

0000

IO-Link 4 IO-Link 3

0000

2...97 Most customers do not use this

functionality. It is used for validation of

slave device details like: Vendor ID,

Device ID or Serial Number. Please

consult the manual for details.

Conﬁguration Data BreakdownReference Image for the IO-Link Port numbering

IO-Link 1 IO-Link 3

IO-Link 2 IO-Link 4

Reading the Process Data – Inputs

5a It is important to note that every standard I/O on the block

is setup as a freely conﬁgurable port. If the controller is

programmed to look for an input and there is an input wired

there, it will be an input. If the controller is programmed to ﬁre

an output, the block will drive an output there.

Description Byte Bit (block pin #)

76543210

Input Data

(Pin Number of Input)

0 07 06 05 04 03 02 01 00

1 15 14 13 12 11 10 09 08

Short Circuit (Pin1 to Pin3)

(Port Number of Status)

2 Port 3 Port 2 Port 1 Port 0

3 Port 7 Port 6 Port 5 Port 4

Overload Status

(Pin Number of Output)

4 07 06 05 04 03 02 01 00

5 15 14 13 12 11 10 09 08

Aux Power Status OK 6 0 0 0 0 0 0 US UA

Reserved Data 7 0 0 0 0 0 0 0 0

Description IO-Link 1 IO-Link 2 IO-Link 3 IO-Link 4 Bit

76543210

IO-Link Slave Device Speciﬁc Data 8...39 56.. 87 104...135 152...183 IO-Link Slave Device - 32 bytes of Input

(For bitmap details, see slave device manual)

DC: Device Connected

IOL: IO-Link Mode OK

40 88 136 184 0 0 0 0 0 0 DC IOL

VF: not typically used, see the manual. 41 89 137 185 0 0 0 0 0 0 0 VF

This tells you the slave device’s vendor info 42, 43 90, 91 138, 139 186, 187 IO-Link Slave Device – Vendor ID Data

This tells you the part number of the device 44...46 92...94 140...142 188...190 IO-Link Slave Device – Device ID Data

Newest Error Reported 47...49 95..97 143...145 191...193 IO-Link Slave Device – Error Code Event #1

(For code details, see slave device manual) 50...52 98...100 146...148 194...196 IO-Link Slave Device – Error Code Event #2

Oldest Error Reported 53...55 101...103 149...151 197...199 IO-Link Slave Device – Error Code Event #3

IO-Link Ports – Input Data

Standard Input Data

(organized by bytes of data in the input buffer of the master block)

(bytes of data in the input buffer of the master block)

Reading the Process Data – Outputs

5b It is important to note that every standard I/O on the block is setup as a freely conﬁgurable port. If the controller is programmed to look for an input

and there is an input wired there, it will be an input. If the controller is programmed to ﬁre an output, it will be an output there. There are diagnostic

inputs available that will indicate an overload on an output from the master block.

Description Byte Bit (block pin #)

76543210

Output Data

(Pin Number of Output)

0 07 06 05 04 03 02 01 00

1 15 14 13 12 11 10 09 08

Restart Output (after overload)

(Pin Number of Output)

2 07 06 05 04 03 02 01 00

3 15 14 13 12 11 10 09 08

Reserved Data 4 0 0 0 0 0 0 0 0

DL: Display Lock / PLC Lock

GN: Display Green LEDs ON

RD: Display Red LEDs ON

5 0 0 0 0 0 DL GN RD

Standard Output Data

IO-Link Ports – Output Data

Description IO-Link 1 IO-Link 2 IO-Link 3 IO-Link 4 Bit

76543210

IO-Link Slave Device Speciﬁc Data 6...37 38...69 70...101 102...133 IO-Link Slave Device - 32 bytes of Output

(For bitmap details, see slave device

manual)

(organized by bytes of data in the input buffer of the master block)

Additional Resources - available on the web

networks.balluff.com

USA

Balluff Inc.

8125 Holton Drive

Florence, KY 41042

Phone: (859) 727-2200

Toll-free: 1-800-543-8390

Fax: (859) 727-4823

E-Mail: balluff@balluff.com

Web: www.balluff.us

Mexico

Balluff de Mexico S.A. de C.V

Anillo Vial II Fray Junípero Serra No.

Colonia La Vista Residencial

Querétaro, QRO 76232

Phone: (++52 442) 212-4882

Fax: (++52 442) 214-0536

E-Mail: balluff.mexico@balluff.com

Web: www.balluff.mx

Canada

Balluff Canada, Inc.

2840 Argentia Road, Unit #2

Mississauga, Ontario L5N 8G4

Phone: (905) 816-1494

Toll-free: 1-800-927-9654

Fax: (905) 816-1411

E-mail: balluff.canada@balluff.ca

Web: www.balluff.ca

Networking & Connectivity

Catalog for selecting speciﬁc

part numbers & accessories

Whitepaper for detailed

information about the beneﬁts

of Distributed Modular I/O

with IO-Link

Add-on-Instructions (AOI) for

use with Allen Bradley PLCs

Distributed Modular I/O

Overview Brochure

Manuals for detailed technical

information about IO-Link

master and slave devices

Visit our website to see more information on IO-Link, including

full product technical specs, applications, brochures, and more.

Doc. No. 893234/Mat. No. 228088 • Edition 1209 • Product specications,

availability, and pricing are subject to change without notice.

Andere Handbücher für BNI EIP-502-105-Z015

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Balluff E/A-System Handbücher

Balluff

Balluff BNI PBS-504-002-K008 Bedienungsanleitung

Balluff

Balluff BNI EIP-507-005-Z040 Bedienungsanleitung

Balluff

Balluff BNI00E7 Bedienungsanleitung

Balluff

Balluff PROFINET BNI PNT-508-055-P067 Bedienungsanleitung

Balluff

Balluff BNI PNT-507-005-Z040 Bedienungsanleitung

Balluff

Balluff BNI00FE Bedienungsanleitung

Balluff

Balluff BNI IOL-727-S51-P012 Bedienungsanleitung

Balluff

Balluff BNI EIP-104-005-E002 Bedienungsanleitung

Balluff

Balluff BNI IOF-329-P02-Z038 Bedienungsanleitung

Balluff

Balluff BIC 1I0-IAA50-M30MI3-SM4A4A Bedienungsanleitung

Balluff

Balluff BNI IOL-719-002-Z012 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung