Bang & Olufsen BeoVision 4 Bedienungsanleitung

BeoVision 4

Guide

For the US-market only!

NOTE: This equipment has been tested and

found to comply with the limits for a class B

digital device, pursuant to part 15 of the FCC

Rules. These limits

are designed to provide

reasonable protection against

harmful

interference in a residential installation.

This equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause

harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

– Consult the retailer or an experienced radio/

TV technician for help.

For the Canadian market only!

This class B digital apparatus meets all require-

ments of the Canadian Interference-Causing

Equipment Regulations.

WARNING: To reduce the risk of fire or

electric shock, do not expose this appliance

to rain or moisture. Do not expose this equip-

ment to dripping or splashing and ensure

that no objects filled with liquids, such as

vases, are placed on the equipment.

To completely disconnect this equipment

from the AC Mains, disconnect the mains

plug from the wall socket. The disconnect

device shall remain readily operable.

The lightning flash with arrowhead symbol

within an equilateral triangle, is intended

to alert the user to the presence of un-

insulated “dangerous voltage” within the

product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and main-

tenance (servicing) instructions in the

literature accompanying the product.

CAUTION: To reduce the risk of

electric shock, do not remove

cover (or back).

No User-serviceable parts inside.

Refer servicing to qualified service

personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This Guide contains all the relevant

information about the connection,

setting-up and use of your plasma

screen with a Bang & Olufsen

BeoSystem.

If you wish to mount the screen in a

wall bracket, please refer to the

Guide enclosed with the bracket.

This chapter describes how to set up the

screen in a BeoSystem setup.

Set up BeoVision 4

– The screen is developed for indoor use in

dry, domestic environments only, and for

use within a temperature range of 10–40°C

(50–105°F).

– The picture can be distorted at altitudes

where the air pressure is lower than 833 hPa

(approximately 1500 m (5000') or higher.

– Do not place any items on top of the screen.

– When lifting the screen, grip the top and

bottom edges (or the appropriate carrying

handles – if any). Remember to carry the

screen in such a way that it is in an upright

position at all times.

– The screen is not designed to stand on its

own. It must be supported until mounted on

a wall bracket or stand. To prevent injury,

use Bang & Olufsen approved stands or wall

brackets only!

– When mounting the screen in a wall bracket,

leave a space of at least 10 cm (4") at the

top, bottom and sides.

– Do not attempt to open the screen. Leave

such operations to qualiﬁed service

personnel!

Make sure to leave adequate space around the

screen for ventilation purposes. Do not cover the

ventilation holes on the rear, as this may cause the

screen to overheat.

Cautions

1Speaker connection panels. These socket are

not to be used when setting the screen up

with a Bang & Olufsen system – use the

Power Link sockets on the BeoSystem

instead.

2System connection panels.

3Mains supply connection.

For safety reasons, you must secure the mains

lead in the cable clamp (A). Otherwise, the mains

cable can be tugged free of the socket.

Overview of connection panels

2 3

Cable connections

>> Set up BeoVision 4

IR receiver: The screen has a built-in IR receiver. It

is therefore not necessary to mount a separat IR

receiver, as it is described in the BeoSystem

Reference book. Only if a projector screen covers

the built-in IR receiver when in use, you must

mount a second IR receiver and connect it to the

second IR-IN socket on your system.

Make the connections while both the screen

and your BeoSystem are disconnected from

the mains.

Connect the screen using the appropriate type

of cables. Refer to the illustration here – and

to the Reference book for your BeoSystem.

If in doubt, contact your Bang & Olufsen

retailer.

When all connections are made, connect your

whole system to the mains supply. The screen

(and the BeoSystem) can only be switched off

completely by disconnecting it from the mains

supply. However, the screen is designed to be

left in standby mode – ready for use.

It is necessary to secure the mains lead in the

cable bands. Otherwise, the mains cable can be

tugged free of the socket.

Sockets on the connection panel

The connection panels on the back of the screen

contain the sockets for connection to the

BeoSystem – and connection to the mains supply.

The socket marked PC IN (covered by a small lid) is

not to be used in a setup with a Bang & Olufsen

system!

SLOT 2 (DVI-connection)

Socket for connection to the socket marked

DISPLAY 1 on the BeoSystem.

SLOT 3 (IR-connection)

Socket for connection to the socket marked IR IN

(9-pin) on the BeoSystem.

SERIAL

Socket for connection to the socket marked

MONITOR on the BeoSystem.

SLOT 1 SLOT 2

DVI-D IR

SLOT 3 PC IN SERIAL

SERIAL DVI

(SLOT 2)

(SLOT 3)

MONITOR

DISPLAY 1

IR IN

(9-pin)

BEOSYSTEM 3

When you press the standby button to switch

off the television after 120 hours of use have

passed since the last calibration, the screen

turns blank with a grey scale bar and a sensor

arm swings down from the television frame.

While the sensor arm calibrates, the bar will

change between various colours. When the

calibration has ﬁnished, the sensor arm

retracts and the television switches off.

Manual calibration sequence

The Auto Colour Management is available in

the on-screen menu, when the system is in

television mode and has been switched on for

more than two minutes.

> Press TV to switch on the system.

> Press Menu to bring up the TV SETUP menu

and press to highlight OPTIONS. (Beo4:

Use ).

> Press the centre button to bring up the OPTIONS

menu and press to highlight AUTO COLOUR

MANAGEMENT. (Beo4: Press GO and ).

> Press the centre button to activate AUTO

COLOUR MANAGEMENT. (Beo4: Press GO). All

text is removed from the menu, the sensor arm

swings down from the television frame and the

calibration process begins. The bar on the

screen will change between various colours.

When the calibration has ﬁnished, the bar is

removed, the sensor arm retracts and the

system returns to the last chosen source. The

message ‘CALIBRATION COMPLETE’ will be

displayed for a few seconds.

If the sensor arm does not swing down fully, the

calibration is not performed and the arm is retracted

if needed. If the calibration is initiated automatically,

the television will attempt to execute the calibration

the next time it is switched off. Contact your Bang &

Olufsen retailer to solve the problem.

Auto Colour Management

The Auto Colour Management auto-

matically compensates for colour

changes on the screen every

120 hours of use. Thereby it ensures

perfect colours on the screen

continuously. It is also possible to

activate the feature manually through

the BeoSystem TV Setup menu.

Do not switch off your system or disconnect it

from the mains during the calibration.

Automatic calibration sequence

PICTURE

select

BRIGHTNESS ...............

CONTRAST ...............

COLOUR .......

........

TINT .......

........

AUTO COLOUR MANAGEMENT

Maintenance

Normal maintenance, such as cleaning

the screen, is the responsibility of the

user. To achieve the best results,

follow the instructions on this page.

Please consult your Bang & Olufsen

retailer to determine recommendations

for normal maintenance.

Cabinet surfaces

Wipe dust off the surfaces using a dry, soft

cloth. Remove grease stains or persistent dirt

with a soft, lint-free, ﬁrmly wrung cloth,

dipped in a solution of water containing only

a few drops of mild detergent, such as

washing-up liquid.

Plasma screen

Clean only with the dry, soft cloth included

with the screen. Do not use liquid cleaners or

aerosol cleaners.

Do not allow still pictures to be displayed on

the screen for an extended period of time, as

this can cause a permanent after-image to

remain on the screen. Examples of still

pictures are logos, video games, computer

images, and images displayed in 4:3 picture

format.

Do not leave the screen in contact with

articles containing rubber or PVC for long

periods of time.

Never use alcohol or other solvents to clean any

part of the screen!

Technical speciﬁcations, features and the use

thereof are subject to change without notice.

The European Parliament and the Council of the

European Union have issued the Waste Electrical

and Electronic Equipment Directive. The purpose of

the Directive is the prevention of waste of electrical

and electronic equipment, and to promote the reuse

and recycling and other forms of recovery of such

waste. As such the Directive concerns producers,

distributors and consumers.

The WEEE directive requires that both manufacturers

and end-consumers dispose of electrical and

electronic equipment and parts in an environmentally

safe manner, and that equipment and waste are

reused or recovered for their materials or energy.

Electrical and electronic equipment and parts must

not be disposed of with ordinary household refuse;

all electrical and electronic equipment and parts

must be collected and disposed of separately.

Products and equipment which must be collected

for reuse, recycling and other forms of recovery are

marked with the pictogram shown.

When disposing of electrical and electronic equip-

ment by use of the collection systems available in

your country, you protect the environment, human

health and contribute to the prudent and rational

use of natural resources. Collecting electrical and

electronic equipment and waste prevents the

potential contamination of nature with the

hazardous substances which may be present in

electrical and electronic products and equipment.

Your Bang & Olufsen retailer will assist with and

advise you of the correct way of disposal in your

country.

Small products may not always be marked with

the pictogram in which case this is present in the

instructions for use, on the guarantee certificate

and printed on the packaging.

This product is in conformity with the

provisions of the Directives 1999/5/EC

and 2006/95/EC.

Waste Electrical and Electronic Equipment (WEEE) – Environmental protection

www.bang-olufsen.com

3509848 0710

Inhaltsverzeichnis

Andere Bang & Olufsen Fernseher Handbücher

Bang & Olufsen

Bang & Olufsen BeoVision L 2502 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoCenter 1 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 1 LS Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSystem 3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision?10-32 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 12-65 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision MX 8000 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoPlay V1 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 7 Produkthandbuch

Bang & Olufsen

Bang & Olufsen BeoVision Avant-55 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 7 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoCenter 6 Produkthandbuch

Bang & Olufsen

Bang & Olufsen BeoVision 10 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision MX 4200 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEOVISION 10-32 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 5 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision Avant Series Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 11-40 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision Horizon-40 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoCenter AV5 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 11-40 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoVision 5 Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Philips

Philips Colour Television Bedienungsanleitung

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung