Banner TCNM-AD Handbuch

Andere Handbücher für TCNM-AD

1

Dieses Handbuch passt für folgende Modelle

2

Inhaltsverzeichnis

Andere Banner Barcode-Lesegerät Handbücher

Banner

Banner ABR7109-MSE2 Bedienungsanleitung

Banner

Banner TCNM AD/EX Bedienungsanleitung

Banner

Banner ABR 3000 series Bedienungsanleitung

Banner

Banner ABR 3000 series Bedienungsanleitung

Banner

Banner Barcode Reader P4 BCR Bedienungsanleitung

Banner

Banner ABR7109-RSE2 Bedienungsanleitung

Banner

Banner ABR Series Bedienungsanleitung

Banner

Banner TCNM-AD Bedienungsanleitung

Banner

Banner ABR 7000 Series Bedienungsanleitung

Banner

Banner IVU BCR Series Bedienungsanleitung

Banner

Banner ABR 3000 series Bedienungsanleitung

Banner

Banner ABR 7000 Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

Atid

Atid AT188N Plus Bedienungsanleitung

AZENTA

AZENTA 281947 Bedienungsanleitung

Sep 2013 p/n 174900 Rev. A

TCNM-AD/EX/SP Scanner Family –

Setup Procedure Using Programming

Barcodes

TCNM-AD/EX/SP Setup Procedure Using Programming Barcodes

2 p/n 174900 Rev. A

Stand-Alone Layout Barcode

To re-program a network scanner for a stand-alone configuration, use the following barcode.

Stand-Alone Layout

Step 1. Press and hold the SMART-TEACH button to enter the “AutoLearn Mode”. Once button is

pressed, the LED cycle appears as follows:

Just pressed. After 2 seconds. After 4 seconds. Release

the button to enter the

AutoLearn Mode.

The laser beam turns ON

and the yellow LEARN

LED blinks: the AutoLearn

Mode is working.

Step 2. Put the barcode related to the planned function in front of the scanner. The picture below

shows, as example, the Restore Default Values barcode1.

Step 3. After the scanner has successfully read the code, the LEDs stay on steady for 2 seconds.

1The barcodes shown are examples, only. Use the barcodes in the Stand-Alone Layout Barcodes section for the

actual programming.

TCNM-AD/EX/SP Setup Procedure Using Programming Barcodes

3 p/n 174900 Rev. A

Successful Reading

Step 4. The scanner is programmed and the AutoLearn Mode ends. The green “ready” LED is on.

Programming Done

The Stand-Alone configuration can also be programmed using

GeniusPlus. Refer to the Help On Line documentation for further details.

TCNM-AD/EX/SP Setup Procedure Using Programming Barcodes

4 p/n 174900 Rev. A

Smart-Teach Key Lock – Unlock Barcode

The SMART-TEACH key can be locked and unlocked through two different methods:

•GeniusPlus parameter

•Programming barcode

The programming barcode procedure uses the AutoLearn Mode described earlier. The code below is a

toggle-code:

•if the key is locked, the programming code unlocks the key

•if the key is unlocked, the programming code locks the key

Restore Default Parameters Barcode

The programming barcode procedure uses the AutoLearn Mode. Use this code to set the scanner to its

factory default values, configuration and environmental parameters: