Barco B324691 Bedienungsanleitung
Rear fan
Installation manual
For CLM
B324691K
R59770230/00
12/02/2008
Barco nv Media & Entertaiment Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
1. General information
1. GENERAL INFORMATION
1.1 Content of the kit
Overview
The kit B324691K can be used in all CLM projectors.
Article number Description Quantity
B324691 Axial fan 24V 75LS 56DB 1
Tabl e 1 - 1
R59770230 REAR FAN 12/02/2008 1
1. General information
2R59770230 REAR FAN 12/02/2008
2. Preparations
2. PREPARATIONS
Removal of the front cover and lamp door.
To remove the front cover and the lamp door, consult the user guide of the projector, chapter “Projector covers, removal and instal-
lation”.
Removal of the lens
To remove the lens, consult the user guide of the projector, section “Servicing”.
Overview
• Removal of the back cover
• Removal of the top cover
• Removal of the side cover
• Removal of the bottom cover
2.1 Removal of the back cover
Necessary tools
Flat screwdriver
How to remove the back cover
1. Release the 3 captive screws in the back cover.
Image 2-1
Release captive screws
2. Pull off the back cover.
R59770230 REAR FAN 12/02/2008 3
2. Preparations
Image 2-2
Remove back cover
2.2 Removal of the top cover
Necessary tools
Flat screwdriver
How to remove the top cover
1. Release the captive screw in the middle of the top cover.
Image 2-3
Remove top cover
2. Pull the cover out of its locks and take it off.
2.3 Removal of the side cover
Necessary tools
Flat screwdriver
How to remove the side cover
1. Loosen both screws.
4R59770230 REAR FAN 12/02/2008
2. Preparations
Image 2-4
Loosen screws
2. Lift up the side cover and pull them forward to take off.
Image 2-5
Side cover removal
2.4 Removal of the bottom cover
Necessary tools
• Flat screwdriver
• Allenwrench8mm
How to remove the bottom cover
1. Remove the 3 plastic legs by turning them off.
Image 2-6
Remove plastic legs
2. Turn out the 3 bolts (A).
R59770230 REAR FAN 12/02/2008 5
2. Preparations
A
A
A
B
B
Image 2-7
Remove the bottom cover
3. Release both screws (B).
4. Take off the bottom cover.
6R59770230 REAR FAN 12/02/2008
3. Installation procedures
3. INSTALLATION PROCEDURES
Overview
• Removal of the back plane
• Replacing the fan
• Mounting the back plane
• Finalizing the installation procedure
3.1 Removal of the back plane
Necessary tools
• Allen wrench 2.5 mm
• Allenwrench3mm
How to remove
1. Disconnect the fan and cut both wire ties.
2. Turn out the 4 screws of the fan outlet grid.
Image 3-1
Remove the outlet grid
3. Take off the grid.
4. Turn out:
- the 4 screws A.
- the 3 screws B
- both screws C
-screwsD
R59770230 REAR FAN 12/02/2008 7
3. Installation procedures
D
A
B
C
Image 3-2
Remove the back plane
5. Take off the back frame
3.2 Replacing the fan
Necessary tools
Allen wrench 2.5 mm
How to replace
1. Turn out the 4 screws.
Image 3-3
Replace the rear fan
2. Take off the fan cover plate.
3. Take off the fan itself.
4. Unpack the new fan and place the new fan on the back plane. The readable text on the rotor must be to outside and the connect
cable must be to the upper side of the back plane
With :
- The readable text on the rotor to the outside
- The connection cable to the upper side of the back plane (when projector is upside down, then to the bottom side).
5. Place the fan cover plate on its place.
8R59770230 REAR FAN 12/02/2008
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Barco Lüfter Handbücher
