Bardic Premium CILLEDNSWP Bedienungsanleitung

CILLEDNSWP

LED TWINSPOT EMERGENCY FLOODLIGHT

WITH SEALED NICKEL CADMIUM BATTERY

WiNET & SENTINEL COMPATIBLE

THE BARDIC WARRANTY

Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement

or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have

the goods repaired or replaced if the goods fail to be of acceptable

quality and the failure does not amount to a major failure.

If the BARDIC emergency lighting ﬁtting (the unit) is found to be

defective due to faulty workmanship or faulty materials used in

its manufacture (but excluding defects due to neglect, misuse or

abuse of the unit by any person) within twelve months of the date of

purchase, it will be repaired free of charge (except the ﬂuorescent

tube and/or the incandescent globe which are not covered by this

warranty) or, at the sole discretion of the manufacturer, replaced. In

either case, return to the purchaser, freight paid.

Any faulty unit should be forwarded FIS to the point of purchase,

accompanied by the sales voucher to establish the date of purchase.

The unit must be clearly marked with the name and address of

the purchaser and the nature of the fault. If the sales voucher is

unavailable at the time of claim, the warranty will be deemed to have

commenced from the packaging date as indicated by the unit date

stamp.

All warranty claims on the unit in question must be received by the

distributor within the twelve month warranty period. This warranty

does not apply to any unit which is situated outside of Australia.

This warranty is in addition to all other warranties rights and remedies

implied by or available under any laws in force in Australia. Any civil

liability of the manufacturer howsoever arising shall insofar as the

same may be legally done be limited at the manufacturer’s option as

follows:

a. Any liability for breach of warranty, subject to the said limitations,

is limited in a case of goods to any one or more of the following

(as selected by the manufacturer):

(i) The replacement of the goods or the supply of equivalent

goods; or

(ii) The repair of the goods; or

(iii) The payment of the cost of replacing the goods or

requiring equivalent goods; or

(iv) The payment of the cost of having the goods repaired

b. And in the case of services such liability shall be limited to any

one of the following (as selected by the manufacturer)

(i) The supplying of the services again;

(ii) The payment of the cost of acquiring those services

again; The manufacturer shall not be liable for any

indirect or consequential loss however and whatsoever

arising.

MPower manufactures a range of emergency lighting ﬁttings without

integral batteries (commonly termed as Slaves), for operation in

conjunction with central power supplies.

MPower will not be responsible for any damages to slave units as a

result of connection to central power supplies operating outside the

voltage parameters speciﬁed for these slave units.

Installation - Maintenance

Testing Instructions

and Warranty

MAINTENANCE RECORD

OWNER: __________________________________________________

ADDRESS: _________________________________________________

INSTALLATION DATE: _____________ LOCATION: ________________

SIX MONTHS CHECK

DATE LIGHT TEST LED TEST LAMP CHECK TESTER

TWELVE MONTHS CHECK

DATE LIGHT TEST LED TEST LAMP CHECK TESTER

BARDIC EMERGENCY LIGHTING

SINGLE POINT UNITS (S.P.U.)

BARDIC LED TWINSPOT FLOODLIGHT

CILLEDNSWP

NICKEL-CADMIUM BATTERY POWERED

WARNING! DISCONNECT SUPPLY BEFORE INSTALLING,

DECOMMISSIONING OR MODIFYING THIS FITTING!

WARNING! The control box should not be opened and

should only be handled by a qualiﬁed competent person.

WARNING! This luminaire is intended only for mounting

in locations where the plug and socket are protected from

unauthorized disconnection.

DESCRIPTION

The Bardic Twin LED Emergency Floodlight is designed to provide

indirect emergency lighting to large, high ceiling areas, such as factories

and warehouses. It features Ultra bright High performance 2 x 10W LED

ﬂoodlights, low standby power consumption and integrated advanced

two stage charging to ensure the high Temperature Ni-Cd batteries are

correctly charged. Designed and tested in accordance to AS/NZS 2293,

AS60598.2.22, EMC.

Box Contents

• Installation Leaﬂet

• CLIIEDNSWP ﬁtting

When the mains supply fails, these units initially provide 2 hours illumination

from a fully charged battery following a 16 hours charge. All models are

intended for connection to 240 V.A.C. +5% -10% 50Hz supply via an

unswitched active.

This model is manufactured to accept the BARDIC SENTINEL automatic

tester or BARDIC WiNET as an optional extra. The SENTINEL will

automatically test the single point units (SPU) every 91 days for operation

in the emergency condition (operation on battery) for a minimum duration

of 90 minutes. The results of the test, fail or pass is Indicated by ﬂashing the

LED (mounted on the SPU) at Intervals:

• ﬂash at 4 seconds on, 1 second oﬀ - Pass

• ﬂash at 0.5 second on, 0.5 second oﬀ - fail

The SENTINEL test program can also be manually initiated. The SENTINEL

option is packed complete with instructions and plugs into the main printed

circuit board (PCB). For further information about BARDIC SENTINEL or

BARDIC WiNET, contact your local dealer or visit www.mpower.com.au.

PRODUCT SPECIFICATIONS

Nominal Voltage: 240V

Nominal Frequency: 50Hz

IP Rating: IP65

Rated Maximum Ambient Temperature: 40oC

Power Consumption: 12VA Maximum

IMPORTANT!

A faulty battery can place severe overloads upon electrical components

in the ﬁtting therefore it is important that the faulty battery be replaced as

soon as possible.

FUNCTIONS

The unit is designed for connection to the mains supply via an unswitched

active, it comes complete with an automatic current and voltage regulated

charger, Nickel Cadmium battery and mains fail sensing capability. The

battery powers two 12 Volt 10W LED ﬂoodlights which are switched on

automatically when the A.C. supply fails and are switched oﬀ when:

1. The battery reaches low voltage cutout, or

2. When AC is restored, or 8 minutes after if the delay function is enabled.

This delay feature is to allow suﬃcient time for the general lighting to restart.

A RED light emitting diode (LED) charge monitor indicates a healthy mains

supply and functioning charger. A test switch to simulate a mains power

failure is included for testing an emergency operation when the mains

supply is healthy.

The LED ﬂoodlights are both powered by the 12 Volt battery but are parallel

connected to ensure independent operation if one lamp fails.

Note: The ﬁtting is shipped with the 8mins delay option enabled by default.

Remove the jumper on the control board to deactivate this feature.

INSTALLATION

NOTE: If the BARDIC SENTINEL or BARDIC WI NET option is to be

ﬁtted, check the installation instructions provided with that product before

proceeding further.

• Remove the screw securing the front panel and take oﬀ panel

• The mounting hole centres of the mounting slots located in the back of the

case are 330mm apart.

• Mark the wall in the desired mounting position keeping the mounting height

of the unit as high as possible above the ﬂoor.

• Drill and plug the mounting screw holes and ﬁt a 38mm x No.8 dome head

screw in each hole allow 7mm of the shaft exposed

• Place the unit onto the mounting screws and fully tighten screws.

• Pass the mains leads through the cable entry hole provided and connect

the active lead to active (A) terminal, neutral lead to neutral (N) terminal and

the earth wire to the earth (E) terminal.

• One lead of the battery has been disconnected to prevent discharge while

in storage. Reconnect this lead.

• Write the date of installation on the battery label.

• Reﬁt the front panel and switch on the A.C. mains supply.

WARNING: Do not touch the surface of the lamp with bare ﬁngers!

COMMISSIONING

IMPORTANT! If the BARDIC SENTINEL or BARDIC WiNET has been ﬁtted

to this spu, then follow their respective commissioning instructions.

1. Switch on mains supply. The charge monitor LEDs will illuminate and the

ﬂoodlights will turn on for approximately 8 minutes and then go oﬀ.

2. Depress the test switch to ensure the ﬂoodlights light up.

3. Release the test switch and note that the ﬂoodlights will remain illuminated

for 8 mins.

4. Allow the unit to operate for 16 hours to fully charge the battery after

which time the unit is ready for duty.

5. A 2 hour discharge test is required as part of the commissioning process

as per AS2293

MAINTENANCE

1. MONTHLY - inspect to ensure charge monitor is illuminated.

2. SIX MONTHLY (or at the discretion of the enforcing Authority) - isolate

the mains supply to unit and allow it to operate until the lamp extin-

guishes. Should the unit provide less than 90 minutes illumination be-

tween 10°c and 40°C ambient temperature following a 16 hour charge,

the unit is faulty and steps should be taken to rectify the fault.

3. TWELVE MONTHLY - Clean all light-emitting/ reﬂecting surfaces.

4. FIVE YEARS TEST - Check ﬁtting runtime against L70 lifetime and

determine if it is still suitable for use.

NOTE: The 6 monthly test should be undertaken wherever possible at times

of least risk (e.g. during daylight hours). This is because of the possibility

of a failure of the normal lighting supply whilst the battery is discharged).

SIX MONTHS CHECK

DAT E LIGHT TEST LED TEST LAMP CHECK TESTER

TWELVE MONTHS CHECK

DAT E LIGHT TEST LED TEST LAMP CHECK TESTER

Andere Bardic Scheinwerfer Handbücher

Bardic

Bardic FAST LiFePO4WER LFSPOT Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung