Barron Games QuadAir Montageanleitung

Quick Tips for QuadAir Operation

The Keys:

Your new QuadAir Keys are located in a compartment located on the base, or wood surface,

which should be facing up while first un-packaging your product.

Dip Switches, and Game play:

*Tip* Credits are per side

Dip Switch 1

Dip Switch 2

Please leave down

Setting the Volume:

The three knobs (2 yellow, 1 black) shown below can be turned clockwise or

counter clockwise to reach the desired volume level. The rail noise is activated

when a puck strikes any of the four side rails. The main volume controls the

attraction music and game play sound.

Setting the Coin Comparator:

1) Side view of your

coin comparator

*Tip* One coin or token must remain in the coin mechanism. All 4 coin

mechanisms need to be set.

Done!

2) Lift coin comparator arm

3) Place currency in cradle. Release arm.

Tips for QuadAir Maintenance

It is highly recommend that all QuadAir playfields are polished weekly and more frequently

during times of high use to keep them both shiny, and smooth.

It is beneficial to use a fine grit sandpaper to smooth the surface of the pucks to keep them

gliding smoothly whenever needed.

Ensure the felts on the base of the mallets are clean and firmly attached to prevent scuffs on the

playfield surface.

Vacuum the inside cavity and blower intake of your air hockey table.

oDust, grime, and other debris can collect inside the body of your table over time. Please

give special attention to the gear in the goal assembly. This may become jammed over

time. *Please see "removing rails" below.

oThe easiest way to access the inside of the table is through the puck drop chute doors

and the blower compartment door located under the table.

Rail Removal:

Locate the seam in the black rubber rail trim which lines the top of the QuadAir table

Use a flathead screwdriver or blunt object to pry the end up, and gently pull the rubber rail trim

from the top of the table. *Caution* This rubber can stretch. *More information on this in

during "rail installation".

The rail screws will be exposed once the rubber rail trim is removed.

You will have access to the goal assemblies once the rail screws and rails are removed from the

table surface.

Goal Assembly troubleshooting:

If the metal puck blocker is "shuttering" or "jumping" up and down:

Turn the game off!

This issue is caused by micro switches that are not being fully engaged. There are two ways to solve this

problem.

The quick way:

Open the puck chute door to view the goal assembly from the bottom side. Make sure that the peg that

is attached to the puck blocker makes firm contact with the micro switch actuator arm. The actuator

arm must be adjusted if the peg does not make firm contact. The arms must be bent in the direction

that the micro switch faces. The one towards the top of the goal must be bent up, the one on the

bottom of the goal must be bent down.

The detailed way:

The rubber rail trim, rails and goal assembly must be removed from the table. With the goal assembly

wires attached, test the side by crediting it and passing a puck through the puck sensor till the gate

raises. Adjusting the actuator arms on the micro switch will be easier with the assembly exposed.

Goal assemblies getting stuck:

After following the steps to remove the goal assembly:

Remove the puck blocker and lay on a flat surface. Use a rubber mallet or any other means to adjust the

blocker and make sure that it is flat. If this piece bends it may cause the teeth to grind with the motor

gear which will in turn break the motor.

Rail installation:

*Important* The rails are in a sequence and cannot be rearranged. Make sure they are put back in the

same spot with the same wire attached to the LEDs. Once the rail screws are in the rails reinsert the

black rubber rail trim. This can be done by hand or with the aid of a rubber mallet.

*Tip* This rubber can shrink if left in the cold. It is much easier to install when warm.

If your table shows 1 life light, and 1 time light it means that the rails are out of sequence. Please

remove them and ensure that the black wire lines up with the GND position on the rail LED strip.

Solenoids misfiring:

Misfiring solenoids can be caused by low voltage. Voltage issues may be from a card swipe system

attached to the 12V power supply in the table or by the knob (technically called a "Trimpot") in the

photo above. It is recommended that customers use an external power source for card swipe systems.

Check the voltage coming out of the power supply and adjust the trimpot by rotating it clockwise or

counterclockwise as necessary to increase or reduce the output, if solenoid issues are not from the card

swipe system.

For comments, questions, and concerns please contact the Barron

Games Service Department at +1(716) 866-0054 or

Service@barrongames.com.

Inhaltsverzeichnis

Andere Barron Games Arcade-Spielautomat Handbücher

Barron Games

Barron Games MAGIC MUSHROOM & MINI BEAR Bedienungsanleitung

Barron Games

Barron Games Timberman Bedienungsanleitung

Barron Games

Barron Games X-Putt Handbuch

Barron Games

Barron Games BG-L001 Bedienungsanleitung

Barron Games

Barron Games BG-W6322DSB Bedienungsanleitung

Barron Games

Barron Games Playair Quadair Bedienungsanleitung

Barron Games

Barron Games 3207545-QAT Bedienungsanleitung

Barron Games

Barron Games BG-X007 Bedienungsanleitung

Beliebte Arcade-Spielautomat Handbücher anderer Marken

Universal Space

Universal Space COCONUT BASH Bedienungsanleitung

Bay-Tek

Bay-Tek EVOLVE Bedienungsanleitung

Global VR

Global VR America's Army Montage- und Bedienungsanleitung

Atronic

Atronic Cashline Bedienungsanleitung

Universal Space

Universal Space Checky Monkey Bedienungsanleitung

Bay-Tek

Bay-Tek Skee Ball 1908 Alley Bedienungsanleitung

Aristocrat Technologies

Aristocrat Technologies Mars X Upright Bedienungsanleitung

Family Fun Companies

Family Fun Companies Reactor Kurzanleitung

Universal Space

Universal Space FRUIT MANIA Extreme Bedienungsanleitung

falgas

falgas CARRUSEL FIESTA Bedienungsanleitung

Konami

Konami DanceDanceRevolution Bedienungsanleitung

Bay-Tek

Bay-Tek quik drop Bedienungsanleitung

Bandai Namco

Bandai Namco PAC-MAN BATTLE ROYALE CHOMPIONSHIP DELUXE Bedienungsanleitung

Adrenaline

Adrenaline Flying Tickets Montage- und Bedienungsanleitung

Swinks

Swinks Stern Pinball Ghostbusters Bedienungsanleitung

Innovative Concepts in Entertainment

Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO Bedienungsanleitung

jakar

jakar SPEED CARS Bedienungsanleitung

Carmelli

Carmelli HAT TRICK NG1015H Bedienungsanleitung