Base Line BL-ETH-SW Bedienungsanleitung
BL-ETH-SW Ethernet Switch
Installation Guide
1-866-294-5847 Rev 04242014 www.baselinesystems.com
Installing the Ethernet Switch in an X Cabinet Enclosure
1. Halt all watering while you install the Ethernet switch.
BaseStation 1000: Press the OFF button.
BaseStation 3200: Turn the dial to the OFF position.
2. Open the internal door of the BaseStation X cabinet enclosure.
3. Find the orange power connector on the wires coming from the transformer. Gently pull the connector away
from the board to disconnect the power.
4. On the right side of the cabinet, locate the 3 mounting pins on the inner wall.
5. Partially thread a screw into the lower mounting pin.
6. Locate the notch on the long edge of the
Ethernet switch mounting plate, and then
position the notch on the partially
threaded screw.
7. Align the upper holes on the Ethernet
switch mounting plate with the upper
mounting pins, and secure the mounting
plate with screws.
8. Tighten the screw in the notch.
9. If it isn’t already connected, attach the
USB-style power connector to the Ethernet
switch port labeled PWR INPUT.
10. Attach the other end of the USB-style
power connector to either of the mini USB
ports on the control board.
11. Attach an Ethernet cable to the communication module (such as a
cell modem gateway or Ethernet radio) and to one of the ports on
the Ethernet switch.
12. Attach another Ethernet cable to the Ethernet switch and to the
back of the controller display.
13. In the third Ethernet port, connect an Ethernet cable to the Ethernet
wall jack.
14. Reconnect the orange power connector to the board in order to
restore power to the controller.
15. Verify that the LEDs on the communication module are illuminated.
16. Close the enclosure door, and then restart the controller.
BL-ETH-SW Ethernet Switch
Installation Guide
1-866-294-5847 Rev 04242014 www.baselinesystems.com
Installing the Ethernet Switch in a Pedestal Enclosure
1. Halt all watering while you install the Ethernet switch.
BaseStation 1000: Press the OFF button.
BaseStation 3200: Turn the dial to the OFF position.
2. Open the front door of the BaseStation pedestal enclosure.
3. Find the orange power connector on the wires coming from the transformer. Gently pull the
connector away from the board to disconnect the power.
4. Locate the 3 mounting pins on the back wall of the enclosure to the left of the control board.
5. Align the holes on the Ethernet
switch mounting plate with the
mounting pins, and secure the
mounting plate with screws as
shown in the illustration.
6. If it isn’t already connected,
attach the USB-style power
connector to the Ethernet
switch port labeled PWR INPUT.
7. Attach the other end of the USB
-style power connector to either
of the mini USB ports on the
control board.
8. Attach an Ethernet cable to the communication module (such as a cell modem gateway or Ethernet
radio) and to one of the ports on the Ethernet switch.
9. Attach another Ethernet cable to the Ethernet switch and to the back of the controller display.
10. In the third Ethernet port, connect an Ethernet cable to the Ethernet wall jack.
11. Reconnect the orange power connector to the board in order to restore power to the controller.
12. Verify that the LEDs on the communication module are illuminated.
13. Close the enclosure door, and then restart the controller.
Inhaltsverzeichnis
Andere Base Line Netzwerk-Router Handbücher
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise