Basler BE1-CDS220 Bedienungsanleitung

INSTRUCTION MANUAL

FOR

CURRENT DIFFERENTIAL SYSTEM

BE1-CDS220

D2857-19

08-18-00

Publication: 9313900990

Revision: B 01/06

BE1-CDS220 Introduction i

INTRODUCTION

This instruction manual provides information about the operation and installation of the BE1-CDS220

Current Differential System. To accomplish this, the following information is provided:

•General information, specifications, and a Quick Start guide.

•Functional description and setting parameters for the inputs and outputs, protection and control

functions, metering functions, and reporting and alarm functions.

•BESTlogic programmable logic design and programming.

•Documentation of the preprogrammed logic schemes and application tips.

•Description of security and user interface setup including ASCII communication and the human-

machine interface (HMI).

•Installation procedures, dimension drawings, and connection diagrams.

•Description of the front panel HMI and the ASCII command interface with write access security

procedures.

•A summary of setting, metering, reporting, control, and miscellaneous commands.

•Testing and maintenance procedures.

•Description of BESTCOMS graphical user interface (GUI).

•Appendices containing time overcurrent characteristic curves, an ASCII command-HMI cross

reference, terminal communications, and settings calculations.

WARNING!

TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ONLY QUALIFIED

PERSONNEL SHOULD PERFORM THE PROCEDURES PRESENTED IN THIS

MANUAL.

NOTE

Be sure that the relay is hard-wired to earth ground with no smaller than 12 AWG

copper wire attached to the ground terminal on the rear of the unit case. When

the relay is configured in a system with other devices, it is recommended to use a

separate lead to the ground bus from each unit.

ii Introduction BE1-CDS220

First Printing November 1999

Printed in USA

January 2006

It is not the intention of this manual to cover all details and variations in equipment, nor

does this manual provide data for every possible contingency regarding installation or

operation. The availability and design of all features and options are subject to

modification without notice. Should further information be required, contact Basler

Electric Company, Highland, Illinois.

BASLER ELECTRIC

ROUTE 143, BOX 269

HIGHLAND, IL 62249 USA

http://www.basler.com, [email protected]

PHONE 618-654-2341 FAX 618-654-2351

CONFIDENTIAL INFORMATION

OF BASLER ELECTRIC COMPANY, HIGHLAND, IL. IT IS LOANED FOR

CONFIDENTIAL USE, SUBJECT TO RETURN ON REQUEST, AND WITH THE

MUTUAL UNDERSTANDING THAT IT WILL NOT BE USED IN ANY MANNER

DETRIMENTAL TO THE INTEREST OF BASLER ELECTRIC COMPANY.

BE1-CDS220 Introduction iii

PRODUCT REVISION HISTORY

The following information provides a historical summary of the changes made to the software, embedded

software (firmware), and hardware of this device. The corresponding revisions made to this instruction

manual are also summarized. This revision history is separated into four categories: BESTCOMS

Software, Application Program Firmware Version, Hardware Version, and Manual Revision. All revisions

are listed (with the month and year) in reverse chronological order with the most recent on top.

BESTCOMS

Software

Version/Date Change

2.01.00/07-05 Improved ability to use special characters in comments.

Enhanced program to work with RS232 converters.

Corrected printout problem with long comments.

Added “Settings Compare” feature.

2.00.01/10-02 Initial 32-bit release.

Improved the 87ND function block diagram.

Corrected tap calculation reporting errors.

Improved programming of Reset Target Logic.

Corrected the SG-COM2 command to be sent out correctly.

1.01.01/12-99 Added ability to create, upload, and download settings files.

Added ability to read fault report directory and fault summary reports.

Improved communications.

1.01.00/05-99 Initial 16-bit release.

Application

Program

Firmware

Version/Date Change

1.15.00/01-06 Minor software enhancements.

1.14.10/11-05 Removed write capability from some Modbusregisters.

1.14.09/07-05 Improved LCD display.

1.14.08/09-03 Added diagnostics for in-house testing.

1.14.07/08-03 Corrected the harmonic sharing inhibit problem.

Enhanced breaker operations counter.

Corrected cal defaults loaded problem when upgrading firmware.

iv Introduction BE1-CDS220

Application

Program

Firmware

Version/Date Change

1.14.05/06-03 Corrected ND timer problem.

Enhanced in-house diagnostics.

1.14.04/10-02 Corrected triggering problem of 2nd oscillography record.

Allowed the differential alarm to be disabled through SA-DIFF serial command.

Improved SER most recent events reporting.

Improved 62 timer function.

Corrected help text for SG-TARG command.

Allowed Trip Led to turn off when current is removed and SG-TARG=0.

Updated 87ND time delay settings.

Correctly improper display of Q demand on LCD.

Moved the degree symbol to the proper location on the LCD for the GND

current.

Improved 50TQ and 51Q time delay functions.

1.14.03/06-01 Fixed the SG-DI command (Setting Group-Demand Interval) so that it now

recognizes a demand interval of three or more digits as being “out of range”.

Added improvements to DNP 3.0, Level 2 protocol.

Added new “Password Security” parameters to Modbus protocol.

Modified display of Phase Angle information (HMI and reports) so that an

asterisk (∗) appears in the angle position if the measured current is below 1%

of rated current (0.05 A for a 5 A relay, 0.01 A for a 1 A relay).

1.14.02/05-01 Corrected firmware problems with Modbus and DNP protocols.

1.14.01/09-00 Added reporting of the protocol option to the COM2 setting screen on the LCD

HMI.

Improved the arrangement of information on the current metering screens on

the HMI.

Added improvements to DNP 3.0 protocol to make it Level 2 compliant.

1.14.00/03-00 Corrected problem that caused the programmable variable names to be limited

to 10 characters instead of 16 characters. This problem occurred with version

1.13.01.

Added Mode 6, Latching Timer to 62 timer functions.

Added DNP 3.0 Protocol.

Added a feature for the demand recording function to allow the user to select

block average or sliding block average calculation method in addition to the

existing thermal calculation method.

BE1-CDS220 Introduction v

Application

Program

Firmware

Version/Date Change

1.13.01/11-99 Added option to select Percent of Average Restraint Current operating

characteristic to the 87R, Percentage Restrained Differential element.

Added Modbus protocol option.

Improved COMTRADE oscillography recording function as follows:

•Provided user setting to partition the 240 cycles of oscillography memory to

provide control over the length of the records.

•Doubled available oscillography memory to 480 cycles when enhanced

recording option is present.

•Added ∗.hdr file in addition to the two files required by the COMTRADE

standard (∗.cfg and ∗.dat) to provide additional information useful in

analyzing the data contained in the oscillographic record.

Improved target reporting function such that the Trip LED on the relay front

panel only latches when there are targets to be displayed on the HMI. The

pickup condition, indicated by the Trip LED flashing, is now a higher priority

than latching to indicate that targets are being displayed on the HMI.

Corrected problem with the 51 inverse overcurrent timing algorithm that could

cause an element to time out too fast when using the V2 curve.

1.12.01/06-99 Improved current check record diagnostic routine.

Corrected problem that caused magnitude in several reporting functions to be

reported in primary amps squared.

Changed several setting defaults.

1.12.00/04-99 Initial release.

Hardware

Version/Date Change

T/08-05 Upgraded U55 on main board to improve LCD.

S/06-05 Improved CT terminal block.

R/01-03 Improved RS-485 communications when slow baud rates are used.

Improved front panel display.

P/05-02 Added labeling to back of case.

Added RTV to ‘s’ wire of T1 to prevent hipot failure.

N/06-01 Improved low-frequency filtering on LCD.

M/03-01 Relocated P2 on magnetics board.

vi Introduction BE1-CDS220

Hardware

Version/Date Change

L/03-01 Changed clearance around Q3 on power supply to prevent shorts.

K/09-00 Improved Surge Withstand Capability.

J/09-00 Improved the RS-485 operation when driving long lines.

I/08-00 Added CE qualification, UL recognition, and CSA certification.

H/08-00 Changed escutcheon plate from mounting holes to mounting studs.

G/04-99 Initial release.

Manual

Revision/Date Change

B/01-06 Added Section 14, BESTCOMS Software.

Re-organized Section 12, Installation.

Added Power System Application Figures 12-26 and 12-27.

A/09-00 Changed the manual organization from two volumes to one volume in a loose

leaf binder with tabs to separate the manual sections.

Added Revision History to the Introduction, and CE qualification, UL

recognition, CSA certification, and DNP 3.0 certification.

Added drawings and minor corrections to all sections.

−/11-99 Initial release.

BE1-CDS220 Introduction vii

CONTENTS

SECTION 1 General Information.............................................................................1-1

SECTION 2 Quick Start...........................................................................................2-1

SECTION 3 Input and Output Functions.................................................................3-1

SECTION 4 Protection And Control........................................................................4-1

SECTION 5 Metering ..............................................................................................5-1

SECTION 6 Reporting and Alarm Functions...........................................................6-1

SECTION 7 BESTlogic Programmable Logic .........................................................7-1

SECTION 8 Application...........................................................................................8-1

SECTION 9 Security ...............................................................................................9-1

SECTION 10 Human-Machine Interface.................................................................10-1

SECTION 11 ASCII Command Interface ................................................................11-1

SECTION 12 Installation.........................................................................................12-1

SECTION 13 Testing and Maintenance..................................................................13-1

SECTION 14 BESTCOMS Software.......................................................................14-1

APPENDIX A Time Overcurrent Characteristic Curves............................................A-1

APPENDIX B Command Cross-Reference ..............................................................B-1

APPENDIX C Terminal Communications..................................................................C-1

APPENDIX D Settings Calculations..........................................................................D-1

viii Introduction BE1-CDS220

This page intentionally left blank.

Andere Handbücher für BE1-CDS220

Inhaltsverzeichnis

Andere Basler Relais Handbücher

Basler

Basler BE1-50BF Bedienungsanleitung

Basler

Basler BE1-59N Bedienungsanleitung

Basler

Basler BE1-59N Bedienungsanleitung

Basler

Basler BE1-27 Bedienungsanleitung

Basler

Basler BE1-DFPR Bedienungsanleitung

Basler

Basler BE1-79 Bedienungsanleitung

Basler

Basler BE1-951 Bedienungsanleitung

Basler

Basler BE1-50/51B-218 Bedienungsanleitung

Basler

Basler BE1-51/27R Bedienungsanleitung

Basler

Basler BE1-25 Bedienungsanleitung

Basler

Basler BE1-81O/U Bedienungsanleitung

Basler

Basler BE1-50/51B-225 Bedienungsanleitung

Basler

Basler BE1-87B Bedienungsanleitung

Basler

Basler BE1-51C Bedienungsanleitung

Basler

Basler BE1-50/51B-237 Bedienungsanleitung

Basler

Basler BE1-40Q Bedienungsanleitung

Basler

Basler BE1-59NC Bedienungsanleitung

Basler

Basler BE1-27 Bedienungsanleitung

Basler

Basler H12345678 R U Bedienungsanleitung

Basler

Basler BE1-50/51M-222 Bedienungsanleitung

Basler

Basler BE1-51 Bedienungsanleitung

Basler

Basler BE1-81 Bedienungsanleitung

Basler

Basler BE1-51 Bedienungsanleitung

Basler

Basler BE1-49 Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

Ruelco

Ruelco 1S04 Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung

Littelfuse

Littelfuse SE-330AU Bedienungsanleitung

EVA Logik

EVA Logik ZW12 Bedienungsanleitung