BAUKER PBS900G Benutzerhandbuch
PBS900G
920W/3" BELT SANDER
ORIGINAL INSTRUCTION MANUAL
EN-2
Important - Please read these instructions fully before starting assembly
General Power Tool Safety Warnings
SAFETY INFORMATION
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
EN-3
Important - Please read these instructions fully before starting assembly
General Power Tool Safety Warnings
suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric
shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
inuence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
EN-4
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c)
Disconnect the plug from the power source and/or
the battery pack from the power
tool before making
any adjustments, changing accessories, or storing
power tools
. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY WARNINGS FOR BELT SANDER
Hold the power tool by insulated gripping surfaces,
because the sanding surface may contact its own
cord. Cutting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
EN-5
1
9 10
6
7
11
8
2 3 4 5
EN-6
2
2
12
9
a
a
A B
C D
E F
G H
I
EN-7
2
2
12
9
a
a
A B
C D
E F
G H
I
EN-8
SYMBOLS
To reduce the risk of injury, user must read instruction manual
Wear eye protection
Wear ear protection
Wear dust mask
Warning
Double insulation
Waste electrical products must not be disposed of with household waste. Please recycle
where facilities exist. Check with your local authorities or retailer for recycling advice.
EN-9
COMPONENT LIST
1. AUXILIARY HANDLE
2. LOCK- ON BUTTON
3. HAND GRIP AREAS
4. DUST EXTRACTION OUTLET
5. DUST BAG
6. BELT COVER
7. BELT CENTERING CONTROL KNOB
8. SANDING BELT
9. ON/OFF SWITCH
10. VARIABLE SPEED CONTROL DIAL
11. SANDING BELT LEVER
12. SANDING PLATE(SEE FIG. F).
Not all the accessories illustrated or described are included in standard
delivery.
TECHNICAL DATA
Type PBS900G (PBS-designation of machinery, representative of Belt
Sander)
Voltage 230-240V~ 50Hz
Power Input 920W
No-load speed 150-270/min
Belt size 77*533mm
Sanding size 76*135mm
Protection class /II
Machine weight 2.95kg
ACCESSORIES
Dust collection bag 1
80 grit Sanding Belt 1
Adapter for a vacuum 1
We recommend that you purchase your accessories from the same store that sold you the
tool. Refer to the accessory packaging for further details. Store personnel can assist you
and offer advice.
EN-10
NOISE DATA
A weighted sound pressure LpA =90.3dB(A)
KpA= 3.0dB(A)
A weighted sound power LwA =101.3dB(A)
KwA: 3.0dB(A)
Wear ear protection.
Vibration Information
Vibration total values (triax vector sum) determined according to EN 62841:
Vibration emission value:
ah = 2.5 m/s2 Uncertainty K = 1.5m/s²
The declared vibration total value and the declared noise emission value have been
measured in accordance with a standard test method and may be used for comparing one
tool with another.
The declared vibration total value and the declared noise emission value may also be used
in a preliminary assessment of exposure.
WARNING: The vibration and noise emissions during actual use of the power tool
can differ from the declared value depending on the ways in which the tool is used
especially what kind of workpiece is processed dependant on the following examples and
other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
The use of the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration and noise accessories are
used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not
adequately managed.
WARNING: To be accurate, an estimation of exposure level in the actual conditions
of use should also take account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle but not actually doing the job. This
may signicantly reduce the exposure level over the total working period.
Helping to minimise your vibration and noise exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti vibration and noise accessories.
Plan your work schedule to spread any high vibration tool use across a number of days.
Inhaltsverzeichnis
Andere BAUKER Sander Handbücher
