Baxi 35/80 IE Versionshinweis
Installation & Servicing Instructions
Baxi System
35/80 IE & 60/100 IE
Gas Fired Wall Mounted System Boiler
Please keep these instructions safe.
Should you move house, please hand
them over to the next occupier.
Page 1
Natural Gas
Baxi System 35/80 IE
Baxi System 60/100 IE
Baxi is one of the leading manufacturers of domestic heating products in the UK.
Our first priority is to give a high quality service to our customers. Quality is designed into
every Baxi product - products which fulfil the demands and needs of customers, offering
choice, efficiency and reliability.
To keep ahead of changing trends, we have made a commitment to develop new ideas using
the latest technology - with the aim of continuing to make the products that customers want to
buy.
Everyone who works at Baxi has a commitment to quality because we know that satisfied
customers mean continued success.
We hope you get a satisfactory service from Baxi. If not, please let us know.
The boiler meets the requirements of Statutory Instrument " The Boiler (Efficiency)
Regulations 1993 No 3083" and is deemed to meet the requirements of Directive 92/42/EEC
on the energy efficiency requirements for new hot water boilers fired with liquid or gaseous
fuels:-
Type test for purpose of Regulation 5 certified by: Notified Body 0051.
Product/Production certified by: Notified Body 0051.
For IE only.
Baxi is a BS-EN ISO 9001
Accredited Company
Page 2
Contents
Section Page
1.0 Introduction 4
2.0 General Layout 5
3.0 Appliance Operation 6
4.0 Technical Data 7
5.0 Dimensions and Fixings 9
6.0 System Details 10
7.0 Site Requirements 12
8.0 Installation 17
9.0 Commissioning the Boiler 26
10.0 Completion 28
11.0 Servicing the Boiler 29
12.0 Changing Components 31
13.0 Illustrated Wiring Diagram 39
14.0 Fault Finding 40
15.0 Short Parts List 43
Page 3
1.0 Introduction
Baxi declare that no substances harmful to health are contained in the appliance or
used during appliance manufacture.
1.1 Description
1. The Baxi System 35/80 IE and 60/100 IE are fully automatic gas fired wall mounted system
boilers. They are room sealed and fan assisted.
2. The boilers are set to give a maximum output of 24.0kW (35/80 IE) or 29.3kW (60/100 IE).
3. They are designed for use on Natural Gas (G20) and can be converted to use Propane
(35/80 IE & 60/100 IE) or Butane (35/80 IE).
4. The boiler incorporates a circulating pump and expansion vessel. It is suitable for use only
on fully pumped sealed systems.
5. The boiler data badge gives details of the model and serial number and is situated on the
control box. It is visible when the case front panel is removed (Fig. 1).
Fig. 1
NOTE: This appliance must be installed in accordance with the manufacturer's
instructions and the regulations in force. Read the instructions fully before installing
or using the appliance.
6. The boiler is intended to be installed in residential / commercial / light industrial E.M.C.
environments on a governed meter supply only.
7. The boiler must be installed with one of the purpose designed flues such as the standard
horizontal flue kit, part no. 247719.
8. All systems must be thoroughly flushed and treated with inhibitor (see section 6.1).
1.2 Installation
The installation must be carried out by a Competent Person and installed in accordance with
the current edition of I.S. 813 "Domestic Gas Installations", the current Building Regulations
and reference should be made to the current ETCI Rules for Electrical Installation.
1.3 Optional Extras
Various flue extensions, bends, vertical flue kits,control accessories etc. are available as
optional extras. These are detailed in a separate publication.
Page 4
2.0 General Layout
2.1 Layout
1. Air Pressure Switch
2. Expansion Vessel
3. Burner Manifold
4. Automatic Air Vent
5. Circulation Pump
6. Drain Off Point
7. Pressure Relief Valve
8. DHW Relay PCB
9. System Pressure Gauge
10. PCB
11. Control Box
12. Flame Sensing Electrode
13. Spark Electrode
14. Burner
15. Primary Heat Exchanger
16. Fan Assembly
17. On/Off/Reset Selector Switch
18. Central Heating Temperature Control
19. Flame Failure
20. Safety Thermostat
21. Fault on Fan or Flue
22. Fault on Pump or Low System Pressure
23. Temperature Indication Only
24. Fault on Central Heating Sensor
25. Power On
26. Hot Water Mode
27. Central Heating Mode
28. Burner On
When neons 19 to 24 are constantly illuminated, they indicate the temperature of the central
heating water.
Page 5
3.0 Appliance Operation
Boiler Primary Circuit
3.1 Operating Mode (Fig. 2)
Fig. 2
Key
1 Heat Exchanger
2 Burner
3 Ignition Electrode
4 Flame Sensing Electrode
5 Gas Valve
6 Pump
7 Automatic Air Vent
8 Pressure Relief Valve
9 Boiler Drain Point
10 Gas Inlet
11 Boiler Flow
12 Boiler Return
13 Pressure Gauge
14 Automatic By-Pass
15 Hydraulic Differential Pressure Sensor
16 Safety Thermostat
17 Central Heating Temperature Sensor
18 Expansion Vessel
19 Water Heating Sensor
1. With a demand for heating, the pump circulates water through the primary circuit. At a pre-
determined flow rate the hydraulic differential pressure switch operates, initiating the ignition
sequence.
2. The main burner ignites at low rate, then the gas valve controls the gas rate to maintain the
heating temperature measured by the temperature sensor.
3. When the flow temperature exceeds the setting temperature, a 3 minute delay occurs
before the burner relights automatically (anti-cycling). The pump continues to run during this
period.
4. When the demand is satisfied the burner is extinguished and the pump continues to run for
a period of 3 minutes (Pump Overrun).
IMPORTANT: When the selector switch is in the '0' (Off) position the electrical
supply to the boiler is isolated. The boiler will not operate.
3.2 Frost Protection Mode
1. The frost protection mode is integral to the appliance and functions only with the selector
switch (see Section 2.1) in the domestic hot water and central heating position. If the system
temperature falls below 5°C then the boiler will fire on its minimum setting until a flow
temperature of 30°C is reached. This will only protect the boiler, not the complete system.
Further protection can be incorporated by using a system frost thermostat.
3.3 Pump Protection
1. With the selector switch (see Section 2.1) in either the central heating or central heating
and hot water position the pump will automatically operate for 1 minute in every 24 hours to
prevent sticking.
Page 6
4.0 Technical Data
4.1 System 35/80 IE
Appliance Type C12 C
32
Appliance Category CATⅡ 2H 3+
Heat Input (Gross)
Max Min
kW 26.3 10.6
Btu/h 89,739 36,170
Heat Output Max Min
kW 24.0 9.3
Btu/h 81,891 31,740
Max Gas Rate (Natural Gas - G20)
(After 10
Mins)
m3/h 2.75
ft3/h 98.12
Burner Pressure (Natural Gas - G20)
Max Rate Min Rate
mbar 12.2 ±0.5 2.5 ±0.5
in wg 4.88 ±0.2 1.0 ±0.2
Inlet Pressure (Natural Gas - G20)
mbar 20
in wg 8
Burner Injector (Natural Gas - G20)
12 x 1.28mm Diameter
Electrical Supply 230V~ 50Hz
(Appliance must be connected to an earthed supply)
Power Consumption 170W
External Fuse
Rating 3A Maximum
Internal Fuse Rating
Fuse 2A Fast Blow to BS 4265
Electrical Protection
IPX5D
NOx
Class 3
Flue Terminal Diameter 100mm
Dimensions Projection 95mm
Connections copper tails
Gas Supply - 3/4"
Central Heating Flow - 3/4"
Central Heating
- 3/4"
Return
Pressure Relief
Discharge - 1/2"
Outercase Dimensions
Casing Height - 780mm
Overall Height Inc
Flue Elbow - 980mm
Casing Width - 450mm
Casing Depth - 345mm
Clearances
Both Sides 5 mm Min
Above Casing 200 mm Min
Below Casing 200 mm Min
Front 450 mm Min (For Servicing)
Front 5 mm Min (In Operation)
Weights kg
Packaged Boiler
Carton 45
Packaged Flue Kit 3
Installation Lift
Weight 37
Central Heating Primary Circuit Pressures
bar
Safety Discharge 3
Max Operating 2.5
Min Operating 0.2
Recommend Operating 1-2
Pump - Grundfos UP 15-60
Available Head See graph below
Expansion Vessel - (Integral with appliance)
bar
Min Pre-charge
Pressure 0.5
litre
Max Capacity of
CH System 125
Primary Water
1.0
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Baxi Kessel Handbücher
Baxi
Baxi LUNA HT 1.650 Handbuch
Baxi
Baxi Barselona Bedienungsanleitung
Baxi
Baxi LUNA DUO-TEC MP+ 1.115 Leitfaden
Baxi
Baxi Megaflo System HE A Range Versionshinweis
Baxi
Baxi POWER HTE Series Bedienungsanleitung
Baxi
Baxi Eco5 Compact+ Bedienungsanleitung
Baxi
Baxi 800 Combi 2 Handbuch
Baxi
Baxi Duo-tec Leitfaden
Baxi
Baxi COMBI 424 Bedienungsanleitung
Baxi
Baxi Bermuda BBU 15 HE Versionshinweis
Baxi
Baxi Bioflo 12 kW Pear Betriebsanleitung
Baxi
Baxi Solo 2 60 RS Benutzerhandbuch
Baxi
Baxi Solo 3 PFL 30 Versionshinweis
Baxi
Baxi Bermuda Inset 2 Boiler 50/4 Datenblatt
Baxi
Baxi Heat 412 Bedienungsanleitung
Baxi
Baxi W. M. 552 OF Kurzanleitung
Baxi
Baxi Platinum Combi HE A Referenzhandbuch
Baxi
Baxi Solo 3 PFL 30 Betriebsanleitung
Baxi
Baxi 110 E Bedienungsanleitung
Baxi
Baxi ECOGEN 24/1.0 Betriebsanleitung
Beliebte Kessel Handbücher anderer Marken
Vaillant
Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung
Radijator
Radijator BIO max 23.1 Bedienungsanleitung
Brunner
Brunner BSV 20 Bedienungsanleitung
Buderus
Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung
Potterton
Potterton 50e Datenblatt
UTICA BOILERS
UTICA BOILERS TriFire Bedienungsanleitung
