Baxi LUNA HT 1.650 Handbuch

Setting Parameters:

The editable parameters are those between 504 and 652. Proceed as follows to access

these parameters:

1. Simultaneously press eys 1 and 4 on the QAA73 controller for

approximately 3 seconds. The message “Initializing BMU parameters”

appears on the display.

2. Simultaneously press eys 1 and 2 for approximately 3 seconds. Parameter

504 will appear on the display.

3. Press ey 1 or 2 to scroll through the list of parameters.

4. To change the value of a selected parameter, press ey 3 or 4 to decrease or

increase the value respectively.

5. Press ey 5 to enter the new values and exit programming of the boiler.

BAXI LUNA HT 1.650 SETUP NATURAL GAS

Luna HT 1.650 Setup Natural Gas

CALIBRATION MODE:

Proceed as follows to enter “calibration mode” on the boiler control panel and calibrate

the gas value:

1. Turn the control knobs 6 and (fig. 1 7 fully counter-clockwise to their

minimum positions as shown below.

2. Starting in this position, quickly turn control knob 7 twice, consecutively,

clockwise approximately a ﾼ turn as shown below in fig. 2.

Note: LED’s 2 and 3 (fig. 4) f ash a ternate y and the disp ay a ternates the message

“SF” and the boi er output temperature every five seconds (fig. 3).

3. Now turn knob 6 to adjust the fan speed to a setting between minimum

thermal power (0% and maximum thermal power (100% .

Note: In “ca ibration mode”, the disp ay a ternates between the message “P” and

the boi er output temperature about every 5 seconds. (fig. 4)

4. Calibration mode remains active for 20 minutes. To exit “calibration mode”

before this time simply turn control knob 7 twice, consecutively, clockwise

approximately a ﾼ turn as shown in fig. 2.

Note: This function is interrupted if the centra heating de ivery temperature

reaches its MAX. SETPOINT.

PROCEED AS FOLLOWS TO CALIBRATE THE GAS VALVE:

1. Ensure your combustion analyzer is set to NG, insert the flue probe into the flue

opening on the top of the boiler, after removing the two flue test port plugs.

2. Calibrate maximum thermal power by turning knob 6 clockwise to max. With the

boiler operating at max. output, check the value for CO2 measured in the flue is

8.7%. If necessary, turn the adjustment screw, or “V” screw, on the gas valve.

Turn c ockwise to reduce the CO2 eve or counter-c ockwise to increase it.

3. Calibrate minimum thermal power. With boiler operating at minimum output by

turning knob 6 counter-clockwise to minimum setting. Check the CO2 value

measured in the flue to 8.4% CO2. If necessary adjust the “K” screw (4mm hex on

the gas valve. Turn c ockwise to increase the CO2 eve or counter-c ockwise

to reduce it.

Note: A ow time between adjustments for your combustion ana yzer to sense the adjusted for your

combustion ana yzer to sense the adjusted CO2 eve . The boi er is now ready for norma operation using NG

gas and can be returned to the service mode by turning contro knob 7.

BAXI LUNA HT 1.650 SETUP NATURAL GAS

Luna HT 1.650 Setup Natural Gas

BAXI LUNA HT 1.650 SETUP NATURAL GAS

Luna HT 1.650 Setup Natural Gas

Resetting the HT 1.650 for Natural Gas

The following must be performed before calibrating the gas valve.

1. Turn the adjusting screw, or “V” screw (2. mm hex) on the gas valve all the way clockwise until the

“V” is bottomed out. Then turn the “V” screw eleven complete revolutions counter clockwise.

2. On the QAA73 controller, which is connected to terminals 4 & on the M2 bus terminal, set

parameters 608 to 24% and parameter 611 to 2000 rpm.

Before lighting Boiler

The following must be performed before calibrating the gas valve.

1. Turn the adjusting screw, or “V” screw (2. mm hex) Five complete revolutions clockwise.

2. On the QAA73 controller, which is connected to terminals 4 & on the M2 bus terminal, set

parameters 608 to 24% and parameter 611 to 2000 rpm.

Setting Parameters:

The editable parameters are those between 04 and 6 2. Proceed as follows to access

these parameters:

1. Simultaneously press keys 1 and 4 on the QAA73 controller for

approximately 3 seconds. The message “Initializing BMU parameters”

appears on the display.

2. Simultaneously press keys 1 and 2 for approximately 3 seconds. Parameter

04 will appear on the display.

3. Press key 1 or 2 to scroll through the list of parameters.

4. To change the value of a selected parameter, press key 3 or 4 to decrease or

increase the value respectively.

. Press key to enter the new values and exit programming of the boiler.

BAXI LUNA HT 1.650 SETUP PROPANE

Luna HT 1.650 Setup Propane

CALIBRATION MODE:

Proceed as follows to enter “calibration mode” on the boiler control panel and calibrate

the gas value:

1. Turn the control knobs 6 and (fig. 1 7 fully counter-clockwise to their

minimum positions as shown below.

2. Starting in this position, quickly turn control knob 7 twice, consecutively,

clockwise approximately a ¼ turn as shown below in fig. 2.

Note: LED’s 2 and 3 (fig. 4) f ash a ternate y and the disp ay a ternates the message

“SF” and the boi er output temperature every five seconds (fig. 3).

3. Now turn knob 6 to adjust the fan speed to a setting between minimum

thermal power (0% and maximum thermal power (100% .

Note: In “ca ibration mode”, the disp ay a ternates between the message “P” and

the boi er output temperature about every 5 seconds. (fig. 4)

4. Calibration mode remains active for 20 minutes. To exit “calibration mode”

before this time simply turn control knob 7 twice, consecutively, clockwise

approximately a ¼ turn as shown in fig. 2.

Note: This function is interrupted if the centra heating de ivery temperature

reaches its MAX. SETPOINT.

PROCEED AS FOLLOWS TO CALIBRATE THE GAS VALVE:

1. Ensure your combustion analyzer is set to LPG, insert the flue probe into the flue

opening on the top of the boiler, after removing the two flue test port plugs.

2. Calibrate maximum thermal power by turning knob 6 clockwise to max. With the

boiler operating at max. output, check the value for CO2 measured in the flue is

10.0%. If necessary, turn the adjustment screw, or “V” screw, on the gas valve.

Turn c ockwise to reduce the CO2 eve or counter-c ockwise to increase it.

3. Calibrate minimum thermal power. With boiler operating at minimum output by

turning knob 6 counter-clockwise to minimum setting. Check the CO2 value

measured in the flue to 9.8% CO2. If necessary adjust the “K” screw (4mm hex on

the gas valve. Turn c ockwise to increase the CO2 eve or counter-c ockwise

to reduce it.

Note: A ow time between adjustments for your combustion ana yzer to sense the adjusted for your

combustion ana yzer to sense the adjusted CO2 eve . The boi er is now ready for norma operation using

LPG gas and can be returned to the service mode by turning contro knob 7.

BAXI LUNA HT 1.650 SETUP PROPANE

Luna HT 1.650 Setup Propane

BAXI LUNA HT 1.650 SETUP PROPANE

Luna HT 1.650 Setup Propane

Using the QAA73 temperature regulator, it is possible to enter into main board LMU34 parameters.

En utilisant la commande distance QAA73 il est possible changer quelque param tres de la carte

lectronique LMU 34.

The editable parameters are those between 504 and 652 (parameters 6 0 and 6 2 are only reading

parameters).

Proceed as follows to access this parameters:

1) Simultaneously press keys 14 on QAA73 remote control for about 3 seconds. The “Initialising

BMU parameters” appears on the display (line 72 ).

2) Simultaneously press keys 12 on QAA73 temperature regulator for about 3 seconds. The

“Initialising BMU SERVICE” (line 04 “TkSmax”).

3) Press keys 12 to scroll through the list of parameters.

4) To change the value of the selected parameter, press key 3-4 to decrease or increase the value

respectively.

5) Press key 5 to enter the new values and exit programming of the boiler’s electronic main board.

Les param tres qui peuvent tre modifi s sont compris entre 504 et 652 (Les param tres 650 et 652 sont

seulement de lecture).

La proc dure pour acc der ces param tres est la suivante:

1) appuyer en m me temps sur les boutons 14 pour environ 3 seconds, jusqu’ l’affichage sur le

display de l’ crit “Initialisation param trage BMU" (par. 725);

2) appuyer en m me temps sur les boutons 12 pour environ 3 seconds, jusqu’ l’affichage sur le

display de l’ crit “Initialisation chauffagiste BMU” (par. 504 “TkSmax”);

) appuyer sur les boutons 12 pour s lectionner les param tres;

4) Pour modifier les param tres affich s appuyer les boutons -4 pour diminuer ou augmenter la

valeur;

5) appuyer sur le bouton 5 pour m moriser et sortir du niveau de programmation.

ADVA CED PARAMETERS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Baxi Kessel Handbücher

Baxi

Baxi Genesis 80 Benutzerhandbuch

Baxi

Baxi Roca LIDIA 20 GT EM Konfigurationshandbuch

Baxi

Baxi DUO-TEC COMPACT 30 GA Bedienungsanleitung

Baxi

Baxi Solo 3 30 PF Betriebsanleitung

Baxi

Baxi Solo HE a series Bedienungsanleitung

Baxi

Baxi Megaflo 2 System 24 Compact GA Bedienungsanleitung

Baxi

Baxi Luna 3 Comfort Bedienungsanleitung

Baxi

Baxi Combi 80e Betriebsanleitung

Baxi

Baxi DUO-TEC MAX+ Leitfaden

Baxi

Baxi POWER HT+ 1.50 Bedienungsanleitung

Baxi

Baxi MainEco Combi 24 Bedienungsanleitung

Baxi

Baxi NUVOLA DUO-TEC GA Series Leitfaden

Baxi

Baxi nuvola3 comfort Leitfaden

Baxi

Baxi LUNA DUO-TEC+ Leitfaden

Baxi

Baxi Combi 105 HE Versionshinweis

Baxi

Baxi LUNA HT 330 Datenblatt

Baxi

Baxi POWER HT-A 1.430 Bedienungsanleitung

Baxi

Baxi Duo-tec Combi GA Kurzanleitung

Baxi

Baxi Combi 630 Bedienungsanleitung

Baxi

Baxi Ecoblue plus combi 24 Bedienungsanleitung

Baxi

Baxi Combi 80 HE Plus Bedienungsanleitung

Baxi

Baxi Duo-tec 2 Combi GA Range Versionshinweis

Baxi

Baxi PRIME HT 240 Bedienungsanleitung

Baxi

Baxi Luna Duo-Tec MP+ 1.90 Leitfaden

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch