Baxi Luna 3 Comfort Bedienungsanleitung

Luna 3 Comfort

Troubleshooting Guide

For Technical Assistance Call: (800)461-4657

June 2008

WARNING!

THIS DOCUMENT IS INTENDED ONLY AS AN

EDUCATIONAL TOOL

This Troubleshooting Guide, and the instructions and suggestions within are

intended solely as an educational tool assisting completely qualified Gas

Appliance Mechanics who have successfully completed the Baxi Installation

Certification Program.

Use of the information herein for the purposes of onsite appliance correction by

untrained personnel may cause extremely dangerous conditions, and may void

the manufacturer’s warranty.

Marathon International assumes absolutely no liability in the execution of the

training suggestions in this document. Should you experience problems or

complications beyond your realm of training, please contact Marathon

International for further instructions.

Resetting The Boiler

There are two types of errors that can be found on the controller:

Fault and Block.

Fault:

If a fault occurs, the display shows symbols flashing with the writing <ERROR>.

The fault is identified by the error code followed by the letter “E” and is not resettable

unless the problem is corrected.

Block:

If a block occurs, the display shows the symbols flashing together with the <ERROR> and

<>>>OK> symbols alternating.

The block fault is identified by an error code (see the table below) followed by the letter “E”.

Press the OK button on the controller to reset the boiler. The display shows the

<RESET> writing followed by the >>>OK writing.

Increase

DHW max.

temperature

Reduce

DHW max.

temperature

On/off

Winter

Summer

selection

Comfort/economy

selection Automatic/manual/

Off/reset

Real/Set

room

temperature

display

Reduce

room

temperature

Increase

room

temperature

Temporary

Special function

Setting

(i.e. holidays,

presence,

shower setting)

Selection of

INFO mode /

Programming

mode

CONTROLLER

These buttons operate

accordingly when in the standard

operation mode. The buttons may

have different functions

depending on operation, and the

programming mode.

iii

CONTROLLER

FUNCTIONS

Types of Functions

• Normal functioning (RUN)

This level is what appears on the controller during normal operation.

• User programming (PROGR)

This level allows the user to set the clock, the date, temperature setpoints and time

programs.

• Advanced information (INFO)

This level allows the installer to set a group of advanced parameters and obtain a

sequence of advanced information on the system functioning.

The programming functions operate as follows:

1. To change from RUN to PROGR shortly press the IP button (on the display you should see the running inscription

<PROGR>) for two seconds then the time will appear.

2. To change from RUN to INFO press the IP button for 3 seconds (you should see the running inscription <INFO>)

appear.

3. To return from PROGR or INFO to RUN shortly press the IP button (you will see the running inscription < RUN>) for

two seconds and the screen will go back to normal.

INFO MODE AND ADVANCED SETTINGS

• “HW O>” DHW inlet or storage tank temperature.

• “HW S^” Set-point water sanitary inlet. Value set up with buttons +/-

• “HW MX” Maximum setpoint sanitary circuit (max. setting value)

• “HW Mn” Minimum setpoint sanitary circuit (min. setting value)

DHW CIRCUIT

• “CH Sl” Maximum setpoint heating circuit, setting value with buttons +/- .

Notice: by pushing the comfort button it is possible to change the temp. value from °C to °F.

• “EXT°c” External temperature (with external connecting probe).

• “CH O>” Temperature water heating inlet pipe.

• “CH S^” Set-point water heating circuit.

• “CH MX” Maximum setpoint heating circuit (max. setting value).

• “CH MN” Minimum setpoint heating circuit (min. setting value).

HEATING CIRCUIT

To enter the Information and Advanced Setting modes it is necessary to press the IP button for at

least 3 seconds; the running words “INFO” should appear.

Once the running words appear, press the OK button to scroll through the parameters; when the

big numbers are blinking it is possible to modify the value using buttons +/- .

ADVANCED INFORMATION

• “PWR %” Power level/flame modulation (in %).

• “P BAR” Water pressure heating circuit (in bar).

• “F l/M” Water flow outlet sanitary circuit (in liters/min).

Advanced Functions

To setting the boiler’s parameters:

1. Press the IP button for at least 3 seconds

2. Hold the button and press the button

When the function is active on the display the F01 will appear and the value of the selected parameter.

3. Use +/- for scrolling through the parameters;

4. Use +/- for changing parameter values;

5. The new value is automatically saved after 3 seconds;

6. Press the IP button to exit.

Advanced Functions

Default Value

Parameter

Number Description 310 Fi 1.310 Fi

1 Type of Boiler

10= Sealed Chamber 20= Atmospheric Chamber

2TypeofGas

00 = Natural Gas 01 = LPG

3 Hydraulic System

00 = Instantaneous Appliance

05 = Appliance with External Water Tank

08 = Heating Only Appliacnce

4 Programmable Relay 1 Setting

2 = Zone System (See Service Instructions)

5 Programmable Realy 2 Setting

13 = Cool Function (See Service Instructions)

6 External Sensor Programmable Input Setting

(See Service Instructions)

7 to 9 Manufacturer Information 0

10 Controller Installation

00 = Wall Mounted

01 = Not Used

02 =Boiler Front Panel Mounted

11 to 12 Manufacturer Information 0

13 CH max. Heating Output (0-100%) 100

vii

Advanced Functions

Default Value

Parameter

Number Description 310 Fi 1.310 Fi

14 D.H.W. max. Heating Output (0-100%) 100

15 CH min. Heating Output (0-100%) 0

16 Maximum Temperature Setpoint Setting

00 = 85ºC 01 = 45ºC

17 Pump Overrun Time

01 - 240 minutes

18 Minimum Burner Pause Time

(01-10 minutes( - 00 = 10 seconds

19 Manufacturer Information 7

20 Manufacturer Information 0

21 Anti-Legionella Function

00 = Disabled 01 = Enabled

22 Manufacturer Information 0

23 Maximum D.H.W. Setpoint 60

24 Manufacturer Information 35

25 Lack of Water Safety Device 0

26 to 29 Manufactuerer Information (Read Only Parameters – –

30 Manufacturer Information 10

31 Manufacturer Information 30

32 to 41 Diagnostics (See Service Instructions) – –

viii

Anomalies

The electronic PCB for the LUNA 3 Comfort is able to memorize the last 10 anomalies which have occurred.

Every anomaly has a counter which increases only if the same anomaly is consecutive; the same mistake non-consecutively is recognized as

new.

To see all the information of every single anomaly you have, go to the Advanced Functions and run down the list of parameters to F32.

Parameters F32 to F38 refer to volatile anomalies which means mistakes with no necessity to Reset (for example DHW probe mistake);

parameters from F39 to F41 refer to anomalies that need to be Reset (e.g. safety thermostat).

Mistakes

without

reset

F32

F33

F34

F35

F36

F37

F38

Mistakes

with

reset

F39

F40

F41

By using the OK button at each of these parameters you can read:

1. ANOMALY CONSECUTIVE NUMBER (F32 is the last one that occurred so it has a 00 value)

2. ANOMALY CODE (xxE – for example 06E, DHW NTC failure)

3. CONSECUTIVE EVENTS FOR THE SAME ANOMALY

4. TIME (days) PASSED FROM THE SIGNALLING (00 means “today”)

5. SYSTEM STATUS

6. SYSTEM PHASE

7. CENTRAL HEATING DELIVERY TEMPERATURE WHEN THE ANOMALY OCCURRED

By using this information you can keep a SERVICE CHART for the boiler.

Andere Handbücher für Luna 3 Comfort

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Baxi Kessel Handbücher

Baxi

Baxi Heat 412 Bedienungsanleitung

Baxi

Baxi LUNA HT 1.450 Benutzerhandbuch

Baxi

Baxi EcoBlue Advance Heat 13 Handbuch

Baxi

Baxi LUNA HT 1.650 Handbuch

Baxi

Baxi Luna 3 Silver Space 250 FI Bedienungsanleitung

Baxi

Baxi 110 E Bedienungsanleitung

Baxi

Baxi MainEco Heat 15 Bedienungsanleitung

Baxi

Baxi MainEco Combi 24 Bedienungsanleitung

Baxi

Baxi Megaflo 2 System 24 Compact GA Bedienungsanleitung

Baxi

Baxi 11p Bedienungsanleitung

Baxi

Baxi LUNA DUO-TEC 1.48 GA Leitfaden

Baxi

Baxi Luna 3 Comfort Bedienungsanleitung

Baxi

Baxi NUVOLA PLATINUM + Leitfaden

Baxi

Baxi Assure 500 Combi 2 Handbuch

Baxi

Baxi Bermuda SP3 Benutzerhandbuch

Baxi

Baxi P-30 Konfigurationshandbuch

Baxi

Baxi Combi 80 HE Plus Bedienungsanleitung

Baxi

Baxi Megaflo System 28 HE IE LPG Versionshinweis

Baxi

Baxi W. M. 552 OF Kurzanleitung

Baxi

Baxi BPI-Eco 1.250 Bedienungsanleitung

Baxi

Baxi CPA-BTH Series Bedienungsanleitung

Baxi

Baxi Assure Heat 13 Bedienungsanleitung

Baxi

Baxi LUNA HT 1.450 Benutzerhandbuch

Baxi

Baxi Megaflo System 15 HE A Benutzerhandbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch