Baxi Megaflo System 15 HE A Bedienungsanleitung

Supplied By www.heating spares.co Tel. 0161 620 6677

Baxi Megaflo System HE IE Range

Gas Fired Wall Mounted Condensing Boiler

User’s Operating Instructions &

Important Warranty Information

Please keep these instructions in a safe place.

If you move house, please hand them over to the next occupier.

Supplied By www.heating spares.co Tel. 0161 620 6677

2© Baxi Heating UK Ltd 2011

be reproduced or transmitted in any form or by any means, or stored in any

retrieval system of any nature (including in any database), in each case whether

electronic, mechanical, recording or otherwise, without the prior written

permission of the copyright owner, except for permitted fair dealing under

Copyrights, Designs and Patents Act 1988.

Applications for the copyright owner’s permission to reproduce or make other

use of any part of this publication should be made, giving details of the proposed

use, to the following address:

The Company Secretary, Baxi Heating UK Ltd,

Brooks House, Coventry Road, Warwick. CV34 4LL

Full acknowledgement of author and source must be given.

WARNING: Any person who does any unauthorised act in relation to a

1.0 Quick Reference Guide 3

2.0 Troubleshooting 4

3.0 Repressurising System 6

4.0 Clearances 7

5.0 Care of the Boiler 8

6.0 Legislation 9

7.0 Notes 10

8.0 Emergency 11

9.0 Warranty & Service 12

Section Page

Contents

Boiler Controls - see opposite page

for Operating Quick Reference Guide

Natural Gas

Baxi Megaflo System 15 HE IE

Baxi Megaflo System 18 HE IE

Baxi Megaflo System 24 HE IE

Baxi Megaflo System 28 HE IE

Baxi Megaflo System 32 HE IE

Propane Gas

Baxi Megaflo System 24 HE IE LPG

Baxi Megaflo System 28 HE IE LPG

ISO 9001

FM 00866

0086

Supplied By www.heating spares.co Tel. 0161 620 6677

1.0 Quick Reference Guide

bar

ON/OFF/Reset

Selector Switch

Display Central Heating

Temperature Control

Calibration Control System Pressure Gauge

OFF Position

The boiler will not operate.

Central Heating Temperature Control

Turn the knob clockwise to increase or anticlockwise to decrease the temperature.

Range 25 - 80° C.

Central Heating & Hot Water Indicator - The indicator will illuminate when the boiler is in

the central heating/hot water mode.

Burner On Indicator - The indicator will illuminate when the burner has fired and is heating

your central heating or domestic hot water.

Boiler Output Temperature - In either the central heating or domestic hot water position

the display will illuminate showing the current boiler temperature in degrees centigrade.

Central Heating System Pressure - The normal operating water pressure is at least 0.2 bar. If

the pressure exceeds 3 bar the safety pressure valve will operate and a fault is indicated.

Contact your Installer.

Central Heating & Hot Water

Both Heating & Hot Water will operate.

Reset

Hold for approx 5 seconds and release.

Display

Calibration Control

This control is for use only by the installer or service engineer.

Supplied By www.heating spares.co Tel. 0161 620 6677

2.0 Troubleshooting

4© Baxi Heating UK Ltd 2011

START

Make sure the gas supply is

turned ON and check if other

gas appliances are operating

(e.g. fire, cooker).

If no gas, consult your

supplier.

Is the ON/OFF/Reset

Select Switch in the

( ) position ?

Is the ( ) light on and the

( ) on ?

Check electricity to the

boiler is switched on.

Is the display lit ?

Display

Central Heating

Indicator

Burner On

Indicator

Boiler operating satisfactorily.

bar

Is the Central Heating System

Pressure above 0.2 bar ?

If the reading falls below 0.2 bar

see Section 3.1.

Does the display show an error

code e.g. E133, E110 ?

Boiler not working

YES YES

YES

Turn the ON/OFF/Reset

Selector Switch to Reset.

Error Code E119 showing low

pressure.

YES

If boiler does not

Reset

Supplied By www.heating spares.co Tel. 0161 620 6677

2.0 Troubleshooting

Is the Timer ON and calling for

heat ?

Ensure timer is set for Central

Heating ON (see any

instructions supplied with

timer).

Is the Room Thermostat (if

fitted) set high enough ?

Turn Room Thermostat to

maximum setting (typical

example shown).

If you don’t know what you need to do to

get the boiler to light, or need help with

the system and controls, contact your

installer as soon as possible.

YES

CONTACT YOUR

INSTALLER OR

SERVICE ENGINEER.

YES

CH ON CH OFF

Typical

examples of

external timer

Supplied By www.heating spares.co Tel. 0161 620 6677

3.0 System Pressure

6© Baxi Heating UK Ltd 2011

3.1 Central Heating System Pressure

1. The boiler may be installed in two types of heating

system, ‘sealed’ or ‘semi - sealed’. Your installer will be

able to advise you of the type of system and explain the

operation.

2. The ‘sealed’ type is pressurised from the mains by

means of a device called the filling loop, which may also

be used to re-pressurise the system.

3. The ‘semi - sealed’ type relies on a header tank of

water to fill the system through a non - return valve.

This type of system should automatically maintain

suitable pressure.

4. The normal operating water pressure must be at least

0.2 bar (Fig. 1) for the boiler to operate. If the pressure

exceeds 3 bar (Fig. 3) the safety pressure valve will

operate and a fault is indicated. Contact your installer.

‘Sealed’ Systems Only

5. It may be necessary to repressurise the system

occasionally (Fig. 2). A filling device (the filling loop) will

be fitted on the system.

6. If you are unsure of its position, or cannot identify it,

consult the installer who fitted the boiler.

7. The filling loop consists of two taps and a separate

metal braided hose with connection fittings.

8. Only when repressurising should the hose be

connected between the two taps. Ensure that the nuts

on the pipe ends are tightened onto the taps.

9. Fully open one of the taps first, and then while

watching the pressure gauge, carefully open the second

tap.

10. When the needle on the gauge is indicating 0.2 or

more turn both taps off.

11. Disconnect the metal braided hose from the taps (a

small amount of water may be present) and remove it.

Keep the hose in a safe place for future use.

‘Semi - Sealed’ Systems Only

12. The header tank on the ‘semi - sealed’ system should

maintain the pressure at a minimum of 0.2 bar. If the

pressure drops below this consult your installer.

bar

Fig. 1

Fig. 2

Normal MINIMUM Pressure

Requires

Repressurising

bar

Fault

Fig. 3

Supplied By www.heating spares.co Tel. 0161 620 6677

4.0 Clearances

Fig. 4

Fig. 5

150mm Min*

780mm

450mm

200mm Min

(300mm Min if

using 80/125mm

flueing system)

5mm Min

450mm Min

For Servicing

Purposes

In Operation

5mm Min 4.1 For your Safety

1. This appliance must have been installed in accordance

with the manufacturer’s instructions and the regulations

in force.

2. Any modification that may interfere with the normal

operation of the appliance without express written

permission from the manufacturer or his agent could

invalidate the appliance warranty.

3. Your boiler must not be operated without the casing

correctly fitted.

4. Do not interfere with any sealed components on this

boiler.

5. Take note of any warning labels on your boiler.

6. Your boiler should have the following minimum

clearances for Safety and Maintenance

(Figs. 4 & 5):-

Top - 200mm

Bottom - 150mm

Left side - 5mm

Right Side - 5mm

Front - 5mm (In Operation)

- 450mm (For Servicing)

*This is the MINIMUM recommended dimension.

Greater clearance than this will aid installation and

maintenance.

7. If your boiler is installed in a compartment, do not use

it for storage purposes. Do not obstruct any purpose

provided ventilation openings.

8. Flammable materials must not be stored in close

proximity to your boiler.

9. Avoid skin contact when your boiler is in operation, as

some surfaces may get hot e.g. pipework.

10. Ensure that the flue terminal, outside the house,

does not become damaged or obstructed, particularly

by foliage.

11. It is important that the condensate drain system is

not blocked, modified or damaged in any way as this

would affect the operation of your boiler. Your installer

should have insulated any exposed pipework.

Supplied By www.heating spares.co Tel. 0161 620 6677

5.0 Care of the Boiler

8© Baxi Heating UK Ltd 2011

5.1 Cleaning the Outer case

1. The painted panels should be wiped with a damp cloth

and then dried completely. DO NOT USE ABRASIVE

CLEANING AGENTS.

5.2 Protection & Precaution

1. The boiler incorporates an integral frost protection feature

that will operate when the selector switch is in ( )

position. If the boiler temperature falls below 5° C, then the

boiler will operate until the water temperature has been

raised.

2. If a system frost thermostat has been fitted (your installer

will be able to advise you), then to operate correctly and

protect your system, the gas and electricity must be left on and

the appliance set in the central heating mode.

3. The boiler incorporates an integral pump protection feature

which continually monitors the time since the pump last

operated. To prevent seizure, the pump will operate for

approximately 1 minute if it has not run in the last 24 hours.

5.3 Fault Indication

1. If a fault occurs on the boiler an error code may be shown

on the facia display.

2. The codes are either two or three digit, preceded by the

letter 'E'. For example, code E133 will be displayed by 'E1'

alternating with '33'. E50 is shown as 'E' then '50'.

3. E20, E28, E50, E125 & E160 indicate faulty components.

You should make a note of the displayed error code and

contact your installer or service engineer.

4. If E110 or E130 is displayed overheat of the primary water

or flue system has occurred. Turn the selector switch to the

reset position and hold for at least 5 seconds. If the boiler

does not relight, or the code is displayed regularly contact your

installer or service engineer.

5. E119 is displayed when the primary water pressure is less

than 0.5 bar. After repressurising the system the boiler should

operate. Your installer will be able to advise you about the

method of repressurising. See page 6 for further details.

6. E133 indicates that the gas supply has been interrupted,

ignition has failed or the flame has not been detected. Ensure

that the gas supply has not been turned off, and turn the

selector switch to the reset position and hold for at least 5

seconds. If the boiler does not relight, or the code is displayed

regularly contact your installer or service engineer.

Central Heating NTC Fault

Flue NTC Fault

Hot Water NTC Fault

Safety Thermostat Operated

Water Pressure Switch Not Operated

Circulation Fault (Primary Circuit)

Flue NTC Operated

Interruption Of Gas Supply or Flame Failure

Fan or Fan Wiring Fault

E20

E28

E50

E110

E119

E125

E130

E133

E160

Table of Error Codes

bar

Display

Then

Fig. 6

Supplied By www.heating spares.co Tel. 0161 620 6677

6.0 Legislation & Maintenance

6.1 Installation, Commissioning, Service & Repair

1. This appliance must be installed in accordance with the

manufacturer’s instructions and the regulations in force.

Read the instructions fully before installing or using the

appliance.

2. The installation must be carried out by a competent

person as stated in I.S. 813 “Domestic Gas Installations”.

6.2 Spare Parts

IMPORTANT - Only a competent person should be

used to service or repair this boiler.

1. Any repairs to the boiler will usually be the

responsibility of the Installer during the guarantee period

after which spare parts may be obtained from

Heatmerchants if required.

2. Quote the appliance name, model number and where

possible the part number when ordering spares. A parts

list is included in the Installation and Servicing Instructions.

3. The name, model number and serial number can be

found on the information label on the back of the hinged

lower door.

6.3 After Sales Service

1. If After Sales Service is required please telephone:-

090 6424 062.

The boiler meets the requirements of

Statutory Instrument “The Boiler (Efficiency)

Regulations 1993 No 3083” and is deemed to

meet the requirements of Directive

92/42/EEC on the energy efficiency

requirements for new hot water boilers fired

with liquid or gaseous fuels:-

Type test for purpose of Regulation 5

certified by:

Notified Body 0085.

Product/Production certified by:

Notified Bodies 0085 & 0086.

For IE only.

Supplied By www.heating spares.co Tel. 0161 620 6677

7.0 Notes

Andere Handbücher für Megaflo System 15 HE A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Baxi Kessel Handbücher

Baxi

Baxi Combi 130 HE Versionshinweis

Baxi

Baxi Combi 80e Betriebsanleitung

Baxi

Baxi LUNA PLATINUM Leitfaden

Baxi

Baxi D SERIES Bedienungsanleitung

Baxi

Baxi Duo-tec Combi 24 HE A Montage- und Wartungsanleitung

Baxi

Baxi LUNA HT 1.350 Bedienungsanleitung

Baxi

Baxi Power HT 1.850 Bedienungsanleitung

Baxi

Baxi ECOGEN 24/1.0 Betriebsanleitung

Baxi

Baxi LUNA HT 1.450 Benutzerhandbuch

Baxi

Baxi Solo 12 HE Benutzerhandbuch

Baxi

Baxi Maxflow Combi WM Betriebsanleitung

Baxi

Baxi LUNA HT 1.850 Bedienungsanleitung

Baxi

Baxi MainEco Combi 24 Bedienungsanleitung

Baxi

Baxi Boston 2 80 RS Betriebsanleitung

Baxi

Baxi LUNA HT 380 Bedienungsanleitung

Baxi

Baxi GA Combi & System Boiler Range Bedienungsanleitung

Baxi

Baxi Megatlo Installationsanleitung

Baxi

Baxi Luna 3 Silver Space Series Produkthandbuch

Baxi

Baxi Platinum Combi HE A Referenzhandbuch

Baxi

Baxi Megaflo System 28 HE IE LPG Versionshinweis

Baxi

Baxi COMBI 228 Bedienungsanleitung

Baxi

Baxi 45 HTE Bedienungsanleitung

Baxi

Baxi 600 System 2 Bedienungsanleitung

Baxi

Baxi Potterton Suprima 30 HE Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch