BEA LZR FLATSCAN SW Bedienungsanleitung

LZR ®-FLATSCAN SW

EN 16005

DIN 18650

DRAFT

SAFETY SENSOR

FOR AUTOMATIC SWING DOORS

User’s Guide for product version 0200 and higher

See product label for serial number

INSTALLATION

When needed, wipe

the laser screen with a

soft, clean and damp

microﬁbre cloth.

Do not use aggressive

products to clean the

optical parts.

• The device cannot be used for purposes other than its intended use. All other uses cannot be

guaranteed by the manufacturer of the sensor.

• The manufacturer of the door system is responsible for carrying out a risk assessment and installing the

sensor and the door system in compliance with applicable national and international regulations and

standards on door safety.

• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate

adjustments of the sensor.

Only trained and

qualiﬁed personnel

may install and setup

the sensor.

The warranty is invalid if

unauthorized repairs are

made or attempted by

unauthorized personnel.

Always test the good

functioning of the

installation before

leaving the premises.

The door control unit

and the door cover

proﬁle must be correctly

earthed.

MAINTENANCE

SAFETY

Avoid vibrations. Do not cover

the front screens. Avoid moving objects

and light sources in

the detection ﬁeld.

Avoid the presence

of smoke and fog in

the detection ﬁeld.

Avoid condensation. Avoid exposure to

sudden and extreme

temperature changes.

Keep the sensor permanently

powered in environments

where the temperature can

descend below -10°C.

Avoid direct exposure to

high pressure cleaning.

LED-SIGNALS

Relay 2

Relay 1

LED ﬂashes LED ﬂashes

slowly LED is off

LED ﬂashes

x times

LED ﬂashes

red-green

DESCRIPTION

1. xation screws (3)

2. mounting base

3. push button

4. master-slave connector

5. main connector

6. hole for master-slave cable

7. clamp (with exible kit)

8. plug (without exible kit)

9. exible kit

10. positioning aids

11. DIP-switch

12. laser head

13. laser window

14. angle adjustment screw

15. cover

16. master-slave cable

LED ﬂashes

quickly

Calculation in progress

Exit the zone and wait

For optimum safety, install 1 module on each door wing side and interconnect

them via the master-slave cable.

3 4

5 mm

MOUNTING

Remove the mounting base. Remove the cover.

Do not hesitate to pull, the cover is very resistant.

Fix the mounting base using the 3 screws.

Make sure the sensor does not collide with any objects

during the door movement.

If necessary, drill a hole for the master-slave cable in

the striped zone.

Pull the master-slave cable through the hole and

position it as shown. Position the sensor in front of the base and pull

the connector through. Then ﬁt the sensor onto

the base by entering the cross-shaped parts into

the cross-shaped holes.

The base has to be attached ﬁrmly.

For optimum safety, install 1 module on each door wing side and interconnect them via the master-slave cable.

«click»

Fasten the sensor on the base by sliding the

sensor downwards until it clicks.

The sensor has to be attached ﬁrmly.

On the SLAVE module, plug the connector and clip

on the plug to cover the hole.

1. Cut the ﬂexible tube if necessary.

2. Insert the cable into the ﬂexible tube.

SLAVE = connected to the master module

On the MASTER module, plug both connectors.

Position the cable wires as shown in order to prevent

water inﬁltration and crushing of the wires.

MASTER = connected to the door controller

3. Position the ﬂexible tube, clip on the clamp and

fasten the screws.

4. Fasten the ﬂexible tube on the other end as shown.

Make sure the ﬂexible tube is not detected.

MASTER = connected to the door controller

Lock the sensor onto the mounting base by fastening

the screw.

The ﬂexible tube should not hang in the pinch zone, because it could cause unwanted detections.

12-24 V DC

COM

OFF

PZ1

WIRING

ORANGE OFF

DIP-SWITCH ADJUSTMENTS

POWER SUPPLY

TEST

STOP IMPULSE

Opening side of the door

REOPENING IMPULSE

Closing side of the door

All wires must be connected. For compliance with EN 16005 and DIN 18650, the door controller test output

must be connected and able to test the sensor.

After changing a DIP-switch, the orange LED ﬂashes. A LONG push on the

push button conﬁrms the settings. Afterwards, a number of green ﬂashes (x)

indicates the number of connected modules.

1 DOOR SIDE 2 ENVIRONMENT 3 BACKGROUND 4 PINCH ZONE

RELAY 1 STANDARD

CRITICAL

OFF

LED during detection:

R1 = RED

R2 = GREEN

RELAY 2

Adjust DIP 1 according to the door side on which the module is mounted.

Adjust the other DIP-settings only if needed.

Switch to CRITICAL when

external disturbances are likely

to cause unwanted detections

(min. obj size, immunity and

uncovered zone are increased).

Switch to OFF when there

is no background (glass

ﬂoor, footbridge...).

Switch to OFF when the hinge

area does not need to be

secured and objects can cause

unwanted detections.

ANGLE ADJUSTMENTS

Adjust the angle of the laser curtain

if needed.

Make sure that the standing testbody

is always detected.

GREEN

FACTORY VALUE

GREEN

BROWN

YELLOW

WHITE

PINK

GREY

RED

BLUE

Always launch a teach-in after changing the angle of the sensor.

In order to change these settings by remote control, adjust the corresponding DIP-switches to ON.

* Output status when sensor is operational.

MASTER

«click»

TEACH-IN

Close the cover starting on the

narrow side. Do not hesitate to push.

Remove the positioning aids from

the base.

Before launching a teach-in, make sure that:

- the door is closed (use the service mode if needed).

- both relays are connected to the door controller and the master-slave cable is connected between the modules.

- the detection ﬁeld is free of snow buildups, heavy rain, snowfall, fog or other moving objects or people.

During the teach-in the sensor learns its environment. If an object is positioned permanentely near the door, the ﬁeld

size will be adapted accordingly. Launch a teach-in after changing the environment or the sensor position or angle.

* A teach-in on the MASTER conﬁgures both the MASTER and the SLAVE. A teach-in on the SLAVE only conﬁgures

the SLAVE.

Launch a teach-in on the MASTER module by push button or remote control*.

1. Wait until the LED ﬂashes green, then indicate the edge of the door wing with your hand.

2. Wait until the LED ﬂashes green again and activate an opening and closing cycle of the door.

3. Wait until the LED goes out.

The service mode deactivates the safety detection during 15 minutes and can be

useful during an installation, a mechanical teach-in of the door or maintenance work.

To enter the service mode, push on the button for at least 2 seconds.

To exit the service mode, push again for at least 2 seconds.

The service mode is deactivated automatically when launching a teach-in.

To open the sensor again, position a

screwdriver in the slot and push until

the cover comes loose.

FINAL STEPS

ALWAYS TEST THE GOOD FUNCTIONING OF THE INSTALLATION BEFORE LEAVING THE PREMISES.

SERVICE MODE

12 2 2

12 2 22

22 3 4

156

15 30 60

DIP 2 = ON

DIP 4 = ON

REMOTE CONTROL SETTINGS (OPTIONAL)

MIN. OBJECT SIZE

HOLDTIME

no ﬁeld

DIMENSIONS

DOOR WING SAFETY

0.01 - 4.00

no ﬁeld 0.01 - 4.00

no ﬁeld

DIMENSIONS

PINCH ZONE SAFETY

0.01 - 1.50

no ﬁeld 0.01 - 4.00

0.3 sec

DOOR WING

HINGE AREA

spots

STANDARD

EXTENDED sec

off off

The standard holdtime maintains the output active for 0.3, 1 or 2 seconds.

When the extended holdtime is chosen, the sensor extends the holdtime during

15, 30 or 60 seconds in case of short detections during the opening of the door.

This parameter deﬁnes the minimum object size to be detected. Its size is represented

by the number of spots it covers in the safety ﬁeld.

A teach-in overwrites these values automatically.

off

A teach-in overwrites these values automatically.

cm*

2 4 6810 12 14 16 18

NO NC NC NO

NC NO NC NO

> > >> > > >

EN 16005

NO NC

DIP 2 = ON

DIP 3 = ON

OUTPUT

CONFIGURATION

UNCOVERED ZONE

NO = normally open / NC = normally closed

ANTIMASKING &

BACKGROUND

OFF OFF ON

OFF ON OFF

ANTIMASKING

BACKGROUND

IMMUNITY FILTER

GENERAL

teach-in full reset partial reset

Factory reset

of all values

Factory reset

of all values exept

ﬁeld dimensions and

output conﬁgurations

See page 7

FACTORY VALUE

Antimasking: protective function which ignores an unwanted object nearby the

laser window masking the vision ﬁeld.

Background: reference point in the detection ﬁeld of the sensor.

If no background is present, switch to off.

Increase to ﬁlter out external disturbances.

The reaction time increases signiﬁcantly between value 5 and 9.

Increase in case of snow, dead leaves, etc.

* measured in speciﬁc conditions and dependant on application and installation.

REMOTE CONTROL SETTINGS (OPTIONAL)

low high

NO POWER

NO DETECTION

DETECTION

2x 3x

HOW TO USE THE REMOTE CONTROL

ADJUSTING ONE OR MORE PARAMETERS

CHECKING A VALUE

RESTORING TO FACTORY VALUES

SAVING AN ACCESS CODE

DELETING AN ACCESS CODE

The access code is recommended for sensors installed close to each other.

After unlocking, the red

LED ﬂashes and the sensor

can be adjusted by remote

control.

If the red LED ﬂashes quickly after unlocking, you

need to enter an access code from 1 to 4 digits.

If you do not know the access code, cut and restore

the power supply. During 1 minute, you can access

the sensor without introducing any access code.

= ﬁeld width: 2.35 m

To end an adjustment session,

always lock the sensor.

Enter the existing code

x = number of ﬂashes = value of the parameter

full reset partial reset

It is recommended to use a different access code for each module

in order to avoid changing settings on both modules at the same time.

Inhaltsverzeichnis

Andere BEA Sicherheitssensor Handbücher

BEA

BEA CRYSTAL Bedienungsanleitung

BEA

BEA IXIO-SO1 I Bedienungsanleitung

BEA

BEA WIZARD II SMR Bedienungsanleitung

BEA

BEA 10MATRIX Bedienungsanleitung

BEA

BEA LZR-FLATSCAN W Bedienungsanleitung

BEA

BEA LZR-WIDESCAN Bedienungsanleitung

BEA

BEA IXIO-DO1 I Bedienungsanleitung

BEA

BEA FLY Bedienungsanleitung

BEA

BEA MS51W Bedienungsanleitung

BEA

BEA LZR FLATSCAN S Bedienungsanleitung

BEA

BEA IRIS Bedienungsanleitung

BEA

BEA IXIO-ST INDUSTRIAL Bedienungsanleitung

BEA

BEA 10LZRWIDESCAN Bedienungsanleitung

BEA

BEA IXIO-SO1 I Bedienungsanleitung

BEA

BEA LZR-FLATSCAN SW Bedienungsanleitung

BEA

BEA MATRIX-3 Bedienungsanleitung

BEA

BEA LZR-MICROSCAN T Bedienungsanleitung

BEA

BEA IXIO-DT1 Bedienungsanleitung

BEA

BEA SBK-30R Bedienungsanleitung

BEA

BEA EAGLE X-MTF Bedienungsanleitung

BEA

BEA LZR-MICROSCAN T Bedienungsanleitung

BEA

BEA IXIO-ST Bedienungsanleitung

BEA

BEA IXIO-S CAN Bedienungsanleitung

BEA

BEA LZR-FLATSCAN 3D SW Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung