Beamz MHL-45 Bedienungsanleitung

Ref. No.: 150.520

MHL-45 DMX Mini Moving Head

Wash

3X 15W COB LED DMX

MANUAL

Table of contents

Unpacking ……………………………………………………….………………………….3

SAFETY INSTRUCTIONS…………………………………………………………………3

SPECIFICATIONS…………………………………………………………………………..4

INSTALLATION………………………………………………………………….…………..4

OPERATION……………………………………………………………………….………...5

Stand alone operation…………………………………………………………….…………5

Master slave operation…………………………………………………………….……..…5

DMX controlled operation………………………………………………………….…….…5

Addressing…………………………………………………………………………….…..…6

Control board………………………………………………………………………….…..…6

DMX protocol………………………………………………………………………….…..…7

CE Declaration ……………………………………………………………………….……8

UNPACKING INSPECTIONS

Unpacking instructions

Please unpack the carton and check the goods carefully when you receive it , if discover

packing damage, shortage or quality problem, please notify the shipper and reject the goods.

Before using this product, please read the instructions carefully and keep it in a safe place for

future reference.

Safety Instructions

Safety and regulatory power socket with high quality output should be used .

Always connect the product to a grounded circuit to avoid the risk of electrocution.

Never put tiny metal objects such as a screwdriver, iron wire and coins, etc. into the internal or

stretch into the machine in case of short circuit .

Please make sure to connect the proper voltage and do not higher or lower than that stated on

the decal or rear panel of the product .

Avoid hitting, crashing or squeezing with other objects in transportation. Never carry the product

from the power cord or any moving part . Always use the hanging / mounting bracket or the

handles.

Never pull or tug on the cord and change it for another one , stop using it when it is damaged or

becomes hot .

Stop using the product once there is sparks when connecting with the power plug .

Make sure there are no flammable materials close to the fixture while operating . Always install

it in a location with adequate ventilation.

Never replace the lighting source with different specification and rating when the original one is

damaged.

Make sure to power off before replacing the light source or the fuse. Never do it while it is on.

The ambient temperature is no more than 40°C(104°F) .

Never clean the fixture by water, thinner or other dissolved agent .

Stop using the product in case of a serious operating problem and send it to our maintenance

agent immediately. Never repair by non-professional workers .

Avoid direct eye exposure to the light source while the product is on.

SPECIFICATION

TECHNICIAL SPECIFICATIONS

Model C315 COB moving wash

Voltage 110V- 250V / 50-60Hz

Power consumption: 65W

LED 3pcsX15w RGB 3 in 1 COB LEDs

Gross Weight 3.5Kgs

Features

11 channel DMX-512 .

Pan :630°/tilt:180°.

Variable electronic strobe.

Variable electronic dimmer(0-100%).

LED display menu with invert.

Reset to factory settings option.

Pan/tilt invert option.

Fan cooled.

Dimensions 28(H) x 22(W) x 27(L) mm

INSTALLATION

Rigging

The installation of the projector has to be built and constructed in a way that it can hold 10 times the

weight for 1 hour without any harming deformation.

IMPORTANT!OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating

working load limits, installation material being used, and periodic safety inspection of all installation

material and the projector. If you lack these qualifications, do not attempt the installation yourself, but

instead use a professional structural rigger. Improper installation can result in bodily injury and or

damage to property. The projector had to be installed out of the reach of people

DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable

material(decoration articles, etc.)within a distance of min.0.5m.

DMX 512 connection/ connection between fixture

The wires must not come into contact with each other, otherwise the fixture will not work at all or

properly. Please note the starting address depends upon which controller is being used. Only use a

DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one

fixture to another

Connection with the mains.

The earth has to be connected. The device must only be connected with an electric installation carried

out in compliance with IEC standards.

OPERATION

After you connected the effect to the mains, The fixture starts running

Stand Alone operation

In the stand alone mode, the fixture can be use without controller

Master/slave-operation

The master/slave-operation enables that several devices can be synchronized and controlled by one

master-device

DMX controlled operation

You can control the projectors individually via your DMX-controller

Addressing

The control board allows you to assign the DMX starting address,

Note;it’s necessary to insert the XLR termination plug (with 120ohm) in the last device in the link in order

to ensure proper transmission on the DMX data link.

CONTROL BOARD

The control board offer several features :you can simple set the starting address, run the

pre-programmed program or make a reset

he main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by pressing

Up or Down .Press the Enter-button in order to select the desired menu. You can change the selection

by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave every

mode by pressing the Mode/Esc-button .The functions provided are described in the following setting.

MENU MAP

The device has two operation modes, It can be operated in StandAlone or in DMX controlled

A001 (address code setting fromA001-------A512)

AU01(auto-moving speediness) AU02(slow speed auto-moving)

SN01(Sound control for color changing) SN02( Sound control for strobe)

RPOF(Set pan to forward-rotating) RPON(Set pan circumrotate reverse)

RTOF(Set tilt to forward-rotating) RTON(Set tilt circumrotate reverse)

RDOF(set the LED readout to non-inverting) RDON(Set the LED readout to inverting)

DFON (Default output setting)

Note：output default setting address code is A001, pan is positive circumrotate、tilt is positive

circumrotate、LED positively reveal.

User configurations

Setup single-desk light`s autocephaly moving mode(auto-running)

.Press the MENU until it shows AU01

.Use the UP/DOWN buttons to set to AU01 or AU02 ,Press ENTER to confirm.

Setup single-desk light`s autocephaly moving mode(sound control)

.Press the MENU button until it shows SNOF .

.Use the UP/DOWN buttons to set to SNOF,press ENTER to confirm.

Master/slave mode(auto-running、sound control)

.This mode will allow you to link up 32 units together without a controller.

.Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of

the units.Proper performance it may be necessary to use a terminator at the last fixture. For more

information about terminators..

Set the desired master-mode- “Automatic program mode” or”sound controlled mode”, for the

master-device, send the DMX address 1 for all slave-devices. Please refer to the instruction under

control board.

To set the pan to reverse

.Press the MENU until it shows RPOF.

.Use the UP/DOWN buttons show RPON, press ENTER to confirm.

To set the tilt to reverse

.Press the MENU until it shows RTOF

.Use the UP/DOWN buttons show RTON, press ENTER to confirm.

To set the LED readout to 180°,rotating

.Press the MENU until it shows RDOF.

.Use the UP/DOWN buttons show RDON, press ENTER to confirm.

Resume reverse Windows default

.Press the MENU until it shows DFON.

.press ENTER to confirm。

DMX-protocol

11 DMX channel mode

Channel Value Function

0-255 Pan

Pan movement 0~630

0-255 Tilt

Tilt movement 0~180

0-255 Pan Tilt speed

Pan & Tilt speed adjustment

0-255 Red

0-100% Red

0-255 Green

0-100% Green

0-255 Blue

0-100% Blue

0-40

41-80

81-120

121-140

141-160

161-200

201-255

Color Change

Neutral

Red

Green

Blue

Green/Blue

Green

Red/Blue

0-10

11-20

21-30

31-200

201-250

251-255

Switching the LEDs/Strobe/Reset

LED OFF

Neutral

Reset

Strobe-effect with increasing speed

Random strobe-effect with increasing speed

Neutral

0-255 Dimmer

0-100% Dimmer

0-255 Pan Fine

Pan fine

0-255 Tilt Fine

Pan fine

0-40, no function, 41-80,red. 81-120,red/blue. 121-140,blue.

141-160,green/blue.161-200,green. 201-255, red/green



CE Declaration of Conformity

Importer: TRONIOSBV

Bedrijvenpark Twente 415

7602 KM - ALMELO

Tel : 0031546589299

Fax : 0031546589298

The Netherlands

Product number: 150.520

Product Description: MHL-45 Wash 3x15W COB LED DMX

Regulatory Requirement: EN 60598-1/-2-17

EN 55015

EN 61547

EN 61000-3-2/-3-3

EN 300 440-1/-2

The product meets the requirements stated in the above mentioned Standards.

13-12-2012

Signature :

Inhaltsverzeichnis

Andere Beamz Scheinwerfer Handbücher

Beamz

Beamz 160.555 Bedienungsanleitung

Beamz

Beamz COB100W Bedienungsanleitung

Beamz

Beamz BS1500H Bedienungsanleitung

Beamz

Beamz 152.780 Bedienungsanleitung

Beamz

Beamz PAR64 DMX 177LED 10mm Bedienungsanleitung

Beamz

Beamz MHL-715WiSpot 7x 15W QUAD DMX 2.4Ghz Bedienungsanleitung

Beamz

Beamz LED Twister 400 Fan RGB DMX Bedienungsanleitung

Beamz

Beamz LCB246 Bedienungsanleitung

Beamz

Beamz MHL1912 Bedienungsanleitung

Beamz

Beamz 150.568 Bedienungsanleitung

Beamz

Beamz Mini Star Ball Sound RGBWA LED 6x3W Bedienungsanleitung

Beamz

Beamz BUV Series Bedienungsanleitung

Beamz

Beamz Neso 1,5W RGB Analog PRO Laser DMX Bedienungsanleitung

Beamz

Beamz LED DJ BANK 120 LEDS Bedienungsanleitung

Beamz

Beamz 153.420 Bedienungsanleitung

Beamz

Beamz Mini Wash 7X10W DMX Bedienungsanleitung

Beamz

Beamz COB150WW Bedienungsanleitung

Beamz

Beamz WBP Series Bedienungsanleitung

Beamz

Beamz 150.581 Bedienungsanleitung

Beamz

Beamz 153.710 Bedienungsanleitung

Beamz

Beamz BSS100 Bedienungsanleitung

Beamz

Beamz 150.530 Bedienungsanleitung

Beamz

Beamz LCB244 Bedienungsanleitung

Beamz

Beamz BPP120 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Bedienungsanleitung