BEC 7800TN Bedienungsanleitung

Configuring a BEC 7800TN

Wireless ADSL Modem

Setting Up the PC | Logging into BEC | Configuring Wireless

Setup | Setup – Static IP

Setup – Main Port | Finished | Firmware Update

ATTENTION!

Before the modem is programmed and installed for the first time, it must have the latest

firmware on it. This can be found by logging into the modem per the instructions below.

On the “Device Info” page find “Software Version”, this should be 2.02e.RC3-dss3. If it is

not, the firmware will need to be update before proceeding.

See Page 14 of this document for instructions on flashing new firmware to the modem.

Setting Up the PC

Before you can get into your new BEC 7800TN Wireless modem, you will need to have the computer's Ethernet interface

to be set up for DHCP, or you will have to set up a static IP address.

Use the following address information if setting up a static IP in the computer's Ethernet interface:

IP ADDRESS: 192.168.10.100

SUBNET MASK: 255.255.255.0

GATEWAY: 192.168.10.1

PRIMARY DNS: 216.129.224.1

SECONDARY DNS: 216.220.0.1

Logging Into the BEC 7800N

In order to log in, open a web browser (Internet Explorer works best for this), and in the address bar type in the following IP

address.

192.168.10.1

After you input the IP address, press the "GO" button or press "ENTER" on your keyboard to access the page. If everything

goes as anticipated, you will see a login screen prompting for username and password (Above).

At this point in the process, input the username and the password as follows:

USERNAME: admin

PASSWORD: NEMONTadmin

After inputting the username and password, simply click the "OK" button. You will be redirected to the default home page of

the modem.

Configuring Wireless

After logging into the modem's home page, click "Wireless" on the left side of the page. Enter the

"SSID" the customer would like to use. This is usually the customer’s last name. Once entered, click

the "Apply" button to save changes.

To setup the wireless security click on the "Security" link on the left side of the page under "Wireless".

The "Select SSID" should show the SSID you entered on previous page.

“WPA/WAPI passphrase” by default is the MAC address (uppercase letters) which is listed on the

underside of the modem on the MAC address label. However, the password can be changed to

anything the customer would prefer to use. The only restriction is that the new key is at least eight or

more characters in length. The current passphrase can be viewed by clicking on the “Click here to

display” link to the right of the passphrase box.

After modifying the information above, click the "Apply" button to save these settings.

****************** IMPORTANT ******************

If the customers wireless network card DOES NOT support WPA then this modem will not work with it.

WEP encryption is NOT available. If customers wireless card will only do WEP then the “Network

Authentication” will need to be set to “None”

Setup

If customer is ADSL/DHCP (Not FTTP), you are done

configuring the BEC 7800TN modem! The modem is now

ready for DHCP authentication.

If customer is FTTP/DHCP then skip to “Setup – Main

Port” on page 12

Proceed to the next page if the customer is NOT ADSL/DHCP or FTTP/DHCP.

After logging into the modem's home page, click the "Advanced Setup" link at the left of the page to

begin configuring your modem.

Next you need to click on the "WAN" link at the left of the page.

Setup – Static IP

This section is only for customers with a static IP.

If customer is DCHP then proceed to “Setup – Main Port” on page 12

To configure the modem with the customers static IP click on the "WAN Service" link to the left. Here

you’ll see two different interfaces.

If the modem is on an ADSL connection then click the “Edit” button for the interface “atm0” and

proceed to the next page.

If the modem is on a FTTP connection then click the “Edit” button for the interface “eth4” and proceed

to the next page.

First uncheck the “Enable” checkbox next to “Obtain an IP address automatically”. Now enter the

customers static IP address in the “WAN IP Address” box. The subnet mask will go in the “WAN

Subnet Mask” box and their gateway IP will go in the “WAN gateway IP Address Box”.

Next the DNS information will need to be put in. Enter these in the “Primary DNS” and “Secondary

DNS” boxes and then click the “Next” button.

At this time the “Primary DNS” is 216.129.224.1 and the “Secondary DNS” is 216.220.0.1

And now click on the "Next" button again.

Andere BEC Netzwerk-Router Handbücher

BEC

BEC Ultimum 8700AXL Bedienungsanleitung

BEC

BEC MX-210NP Bedienungsanleitung

BEC

BEC BEC 7800(N) Bedienungsanleitung

BEC

BEC MX-221P Bedienungsanleitung

BEC

BEC M2M MX-1000e Bedienungsanleitung

BEC

BEC MX-200 Bedienungsanleitung

BEC

BEC 5200 Series Bedienungsanleitung

BEC

BEC 6600AEL Bedienungsanleitung

BEC

BEC 7700N Bedienungsanleitung

BEC

BEC 4700A Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

BEC

BEC 5102 Series Bedienungsanleitung

BEC

BEC 7402GTM Bedienungsanleitung

BEC

BEC 7700N Bedienungsanleitung

BEC

BEC MX-200A Bedienungsanleitung

BEC

BEC 8800N Bedienungsanleitung

BEC

BEC 5200 Series Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

BEC

BEC 7404 Series Bedienungsanleitung

BEC

BEC RidgeWave 7000 R26-W Bedienungsanleitung

BEC

BEC 7800 Bedienungsanleitung

BEC

BEC 7300 Series Bedienungsanleitung

BEC

BEC RidgeWave 6900 Bedienungsanleitung

BEC

BEC BEC 6500AEL Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung