BEGA 77 153 Handbuch

Inhaltsverzeichnis

Andere BEGA Scheinwerfer Handbücher

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Bedienungsanleitung

Installation and Technical Information

BEGA

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

Replacement Parts

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

LED Facade Floodlight 77 153

Tools Required:

5mm hex key

Adjustable wrench

Weight: 12.1 lbs.

Dimensions

A: 39-3/8 ”

B: 4-1/2 ”

C: 2-1/4 ”

Relamping/Maintenance

No relamping required.

Lamp: 39.2W LED

77 153

7/10/2018

Page 1 of 2

Description

LED (3000K) (2x)

LED (4000K) (2x)

Driver (120-277V)

Part No

LED-0612/830

LED-0612/840

75969-02

Notice to Installer for 77 153:

1. See page 2 for specic product safety warnings.

2. Integral LED module and driver provided by BEGA within luminaire housing.

3. Leader cable must be secured to a wet location rated junction box with UL Listed or CSA

Certied liquid tight cord grip suitable for exible leader cable provided. Outer diameter

of the 5-wire 77 284 leader cable: 0.35” - 0.38”.

77 153 - installation:

1. Loosen (2) 5mm captive hex screws and detach mounting base from luminaire.

2. Attach base to nished mounting surface with (2) screws and washers (by others).

3. Adjust aiming, if desired, by removing (2) hex nuts and washers to detach mounting base

from mounting plate. Move mounting base on ribbed track of mounting plate to desired

aiming location. Reattach mounting base to mounting plate with hex nuts.

4. Remove end cap from 5-pin connector and connect luminaire cables to leader and/or

jumper cables. Leave endcap on 5-pin connector if not attached to either a leader or

jumper cable.

5. Direct connected cables through openings on either end of mounting base and replace

luminaire. Tighten (2) hex screws to secure.

6. Make leader cable wiring connections in wet location wiring box (by others):

MAIN VOLTAGE SUPPLY WIRE TO BLACK LEADER WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LEADER WIRE

GREEN GROUND WIRE TO GREEN LEADER WIRE

Dimming (if applicable):

DIMMING CONTROL WIRE (+) TO POSITIVE LEADER DIM WIRE

DIMMING CONTROL WIRE (-) TO NEGATIVE LEADER DIM WIRE

Figure 1:

Mounting Base

Mounting Plate

Luminaire

Installation and Technical Information

BEGA

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

LED Facade Floodlight 77 153

77 153

7/10/2018

Page 2 of 2

Product Safety Warnings:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

SUITABLE FOR WET LOCATIONS.

MIN 60°C SUPPLY CONDUCTORS.

CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT

BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.

CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 60°C MIN.