BEGA 77 756 Handbuch

Inhaltsverzeichnis

Andere BEGA Scheinwerfer Handbücher

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Bedienungsanleitung

Installation and Technical Information

BEGA

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2017

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Replacement Parts

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

180° Glare Shield 70 755

Elliptical Spread Lens 70 050

77 756

LED compact oodlight - outrigger

Tools Required:

4mm hex key

5mm hex key

Flat head screw driver medium

Phillips head screw driver medium

Protection Class: IP65

Weight: 4.9 lbs

Dimensions

A: 4-1/8 ”

B: 27-1/2 ”

C: 4-3/8 ”

D: 7-1/2 x 3-1/2 “

Relamping/Maintenance

No relamping necessary.

Lamp: 6.5W LED

77 756

12/4/2017

Page 1 of 2

Description

Di󰀨user

Gasket

LED driver (120V-277V)

LED module (4000K)

Part No

140850

831652

75943

LED-0329/840

Notice to Installer for 77 756:

1. This product must be installed in accordance with the applicable installation code

by a person familiar with the construction and operation of the product and the

hazards involved.

2. Mounts directly over a standard, vertical single gang wiring box (by others).

3. Ceiling and wall applications only.

4. In conformance with U.L. Standards 1598, a silicone-based sealant MUST be

used between the mounting plate edge and supporting wall.

5. WARNING: LEDs are high quality electrical components. Please avoid touching

them directly during installation.

77 756 - installation:

1. Loosen the (4) 4mm hex screw on the luminaire canopy and remove

luminaire base from luminaire.

2. Feed luminaire wiring through the luminaire base and mounting plate.

3. Make supply wiring and luminaire wiring connections inside the wiring box:

MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE

GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE

Dimming (if applicable):

DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE

DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE

4. Mount luminaire to ceiling or wall using hardware (by others). Minimum

size: 8-32 screws

5. Replace luminaire canopy (with luminaire attached) and tighten (4) 4mm screws.

8. To adjust head angle, use 5mm hex key to loosen adjustment screw. Adjust

luminaire head as needed and tighten adjustment screw.

Installation and Technical Information

BEGA

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2017

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

77 756

LED compact oodlight - outrigger

77 756

12/4/2017

Page 2 of 2

Product Safety Warnings:

CAUTION - RISK OF FIRE. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND

THE HAZARDS INVOLVED. SUITABLE FOR WET LOCATIONS.

MIN 90°C SUPPLY CONDUCTORS.

ATTENTION - RISQUE D’INCENDIE. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT,

PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES

INHÉRENTS. CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 90°C MIN.