BEGA 88 309 Handbuch

Inhaltsverzeichnis

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung

LIGMAN

LIGMAN DE-20023 Bedienungsanleitung

Spectroline

Spectroline MAXIMA ML-3500 Series Bedienungsanleitung

Installation and Technical Information

BEGA

Replacement Parts

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

Pole top - indirect 88 309

Tools Required:

5mm hex key

6mm hex key

8mm hex key

Adjustable wrench

Protection Class: IP65

Weight: 50.0 lbs.

Dimensions

A: 39-3/8 “

B: 24-1/4 “

Relamping/Maintenance

No relamping required.

Lamp: 55.3W LED

88 309

10/9/2018

Page 1 of 2

Description

Lens

Lens gasket

Reector disc

Driver (120-277V)

LED Module (3000K)

LED Module (4000K)

Part No

140273

830647

710945

75976

LED-0721/830

LED-0721/840

Notice to Installer for 88 309:

1. For pole top applications only.

2. Slip ts 3” O.D. pole top or tenon.

3. Luminaire requires ballast mounted in minimum 5” butt hinge base pole. NOTE:

Lower pole before installing luminaire and ballast tray.

4. Luminaire requires at least 3-1/2” of straight diameter pole or tenon.

88 309 assembly:

1. Loosen the (2) 8mm hex screws at the top of the support rods and remove

screws and xing plates.

2. Attach the reector disk to the support rods by positioning the joint shells over

the joint bearings. Make sure the drip edges are oriented downwards.

3. Replace the xing plates and screws.

4. Tilt the reector to the desired orientation (0-30 degrees). Consult factory for

non-adjustability option.

5. Tighten the (2) 8mm screws to secure in place.

88 309 - installation:

1. Carefully hinge down pole, exposing bottom of pole.

2. Route the luminaire wiring through to the pole top base and slip luminaire over

the top of the pole.

3. Tighten the (8) 5mm set screws evenly to secure to pole.

4. Make wiring connections from luminaire wires to gear tray wires:

BLACK LUMINAIRE WIRE TO BLACK MARKED SOCKET WIRE

WHITE LUMINAIRE WIRE TO WHITE MARKED SOCKET WIRE

GREEN LUMINAIRE WIRE TO GREEN GROUND WIRE

5. Place the gear tray in the base of the pole and tighten the 5/16” hex bolt to

wedge inside pole and secure.

6. Make supply wiring connections to gear tray wires:

MAIN VOLTAGE SUPPLY WIRE TO BLACK DRIVER WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE DRIVER WIRE

GREEN GROUND WIRE TO GREEN DRIVER WIRE

7. Replace pole to upright position and secure by tightening (3) base bolts.

IMPORTANT: PLEASE NOTE THE WEIGHT OF LUMINAIRE HEAD ON

POLE AND TAKE CAUTION ACCORDINGLY DURING POLE TILT

Installation and Technical Information

BEGA

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Pole top - indirect 88 309

88 309

10/9/2018

Page 2 of 2

Product Safety Warnings:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

SUITABLE FOR WET LOCATIONS.

MIN 60°C SUPPLY CONDUCTORS.

CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT

BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.

CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 60°C MIN.