Beijer Electronics IFC MC Bedienungsanleitung

IFC MC

Manual

MA00281C 2001-12 English, Svenska

Foreword

Beijer Electronics

Manual IFC MC

Foreword

This manual describes the installation and functions of the memory expansion

card IFC MC.

The expansion card is used to connect a PCMCIA flash memory card to opera-

tor terminals with expansion slots.

IFC MC supports the flash memory cards 4MB (SM9AMD4M002) and

8 MB (SM9AMD8M002) from SMART Modular Technologies.

For information about the flash memory card, please contact the dealer.

Besides this manual, the manual for the operator terminals and the

programming tool for the operator terminals is also available.

 Beijer Electronics AB, MA00281C, 2001-12

All examples in this manual are used solely to promote understanding of how the equipment works and its

operation. Beijer Electronics AB takes no responsibility if these examples are used in real applications.

Because of the great many application areas for this equipment, the user himself must acquire the

appropriate knowledge needed to use the equipment correctly for particular applications.

Beijer Electronics AB absolves itself of all responsibilities for damage and injuries that may occur during

installation or use of this equipment.

Beijer Electronics AB absolves itself of all responsibilities for any type of modification made to the

equipment.

Beijer Electronics AB absolves itself of all responsibilities for damage caused to its products by other brands

of equipment linked to them.

Foreword

Beijer Electronics

Please fill this form out with any suggestions regarding the manual.

This page, or a copy of it, can be sent to us at the addresses below.

Name ....................................................................................

Company....................................................................................

Address ....................................................................................

City, Zip code.............................................................................

Country ....................................................................................

Telephone...............................Fax...............................................

E-mail ....................................................................................

Please fax this page to the Marketing epartment,

Beijer Electronics AB at +46-40-93 23 01,

or send it by conventional mail to

The Marketing epartment, Beijer Electronics AB

Box 426, SE-201 24 MALMÖ, Sweden.

Comments can also be sent to manual@beijer.se.

Comments regarding MA00281C Page

Safety precautions

Beijer Electronics

Safet precautions

General

– Check the delivery for transport damage. If damage is found, advise the

supplier.

– The product fulfils the requirements of article 4 of EMC directive

89/336/EEC.

– Do not use the product in an explosive environment.

– Modifications, changes and additions to the product are forbidden.

– Use only spare parts approved by Beijer Electronics AB.

– Read the user instructions carefully before use.

– The equipment should be operated by qualified personnel only.

At installation

– The product is constructed for stationary installation.

– Install the product according to the accompanying installation instructions.

– The product must be grounded according to the accompanying installation

instructions.

– The equipment must be installed by qualified personnel.

– Separate cables for high voltage, signals and supply.

– The product should not be mounted in direct sunlight.

In use

– Keep the equipment clean.

– Emergency stop and other safety functions should not be controlled from the

terminal.

– Do not touch the keys, displays, etc. with sharp objects.

Safety precautions

Beijer Electronics

Service and maintenance

–The agreed guarantee applies.

–Clean the display and face with a soft cloth and mild detergent.

–Repairs should be made by qualified personnel.

At disassembl and scrapping

–Local regulations apply concerning recycling of products or parts.

–Please note that the electrolyte condenser and display contain hazardous

substances.

Contents

Beijer Electronics

Contents

1Installation................................................................................................8

1.1 Installation of one expansion card................................................8

1.2 Installation of two expansion cards.............................................10

2 Settings in the programming tool...........................................................12

2.1 Define slot .................................................................................12

2.2 Transfer the settings...................................................................15

3 Functions for the memory card ..............................................................16

3.1 Backup.......................................................................................16

3.2 Memory expansion ....................................................................17

Contents

Beijer Electronics

Installation

Beijer Electronics 8

1 Installation

When the operator terminal is started with a formatted IFC MC card installed,

the system detects if the memory card is formatted as a memory expansion card

or as a backup card. The backup function makes it easy to, for example, copy

projects between different terminals.

The system program (operating system/firmware) in the operator terminals

must be of the same version if IFC MC is used as a backup card to copy projects

or files between different terminals.

The memory card can only be read and written to by the terminal, and not by a

personal computer.

This chapter describes how to mount the memory card in the terminal.

1.1 Installation of one expansion card

Perform the following steps to mount the IFC MC expansion card:

1. Switch the terminal power off.

2. Make sure that the ESD protection is good.

3. Remove the cover plate on the rear of the terminal, and the two expansion

plates on the short side. In terminals equipped with two expansion slots, the

slots are called Slot 1 and Slot 2. In terminals with one expansion slot, it is

called Slot 1.

Slot 1

Slot 2

Installation

9Beijer Electronics

4. Put the jumper J1 on the expansion card in the position SLOT 1 if the

expansion card is mounted in Slot 1, and in position SLOT 2 if the card is

mounted in Slot 2.

5. Mount the expansion cables with the components of the expansion card

placed upwards. One of the expansion cables is mounted between X1 on the

CPU card and X1 on the expansion card, and the other cable between X2

on the CPU card and X2 on the expansion card.

6. Fasten the card with the spacers or the screws. Use the screws if the expan-

sion card is mounted in Slot 1, and the spacers if the card is mounted in

Slot 2.

7. Check that the expansion cable is correctly mounted.

8. Mount the cover plates.

Installation

Beijer Electronics 10

1.2 Installation of two expansion cards

Two expansion cards can be mounted in some terminals. They are mounted in

parallel to the connector on the CPU card in the terminal. Two expansion cards

can be connected via one expansion cable since there is a parallel contact on the

cable. The connector in the middle is used for the expansion card placed in Slot

1 and the end connector is used for the expansion card placed in Slot 2. If only

one card is used either connector can be used.

The connector X1 on the expansion card in Slot 2 is connected to the connector

X1 and the CPU card in the terminal via the X1 connector on the expansion

card in Slot 1. If the X2 connector on the CPU card in the terminal is used by

any or both cards, this connector is connected to the X2 connector on the

expansion card.

When two expansion cards are mounted in the same terminal the card in Slot 1

is mounted with the distances and the card in Slot 2 with the screws in the dis-

tances.

Note!

Only one IFC MC can be used in the terminal.

Card in

Slot 2

Card in

Slot 1

Andere Handbücher für IFC MC

Inhaltsverzeichnis

Sprachen:

Andere Beijer Electronics Bedienfeld Handbücher

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

Beijer Electronics

Beijer Electronics iX Panel T60 Bedienungsanleitung

Beijer Electronics

Beijer Electronics EPC TA100 AM Bedienungsanleitung

Beijer Electronics

Beijer Electronics iX T15B Bedienungsanleitung

Beijer Electronics

Beijer Electronics T15B Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 web Bedienungsanleitung

Beijer Electronics

Beijer Electronics C2 base Bedienungsanleitung

Beijer Electronics

Beijer Electronics M70 Bedienungsanleitung

Beijer Electronics

Beijer Electronics QTERM-IV Bedienungsanleitung

Beijer Electronics

Beijer Electronics iX Panel TA70 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten