Beko METPOINT CID Bedienungsanleitung

METPOINT® CID

10-403

Quick Start Guide

Table of contents

1. Safety instructions...........................................................................................................................4

1.1 About this document ...................................................................................................................................4

1.2 General safety instructions ........................................................................................................................4

1.3 Using Class 2 lasers ...................................................................................................................................... 4

1.4 Environmental protection........................................................................................................................... 4

2. Intended use.....................................................................................................................................5

3. Technical data ..................................................................................................................................5

4. Marking ............................................................................................................................................6

4.1 Type plate........................................................................................................................................................6

4.2 Laser warning label.......................................................................................................................................6

4.3 Label locations...............................................................................................................................................6

4.3.1 The METPOINT®CID (standard and laser distance module) ................................................. 6

4.3.2 Parabolic mirror.................................................................................................................................6

5. Device components and controls....................................................................................................7

6. Preparing the device........................................................................................................................8

6.1 Changing the language................................................................................................................................8

6.2 Checking the current rmware and updating the rmware ...............................................................8

6.3 Conguration...............................................................................................................................................10

6.3.1 Conguring parameters.................................................................................................................11

6.3.2 Conguring the measuring point................................................................................................11

7. Commissioning / use..................................................................................................................... 12

7.1 Switching on the device ............................................................................................................................12

7.2 Headphone volume up / down ................................................................................................................12

7.3 Laser ON / OFF............................................................................................................................................12

8. Automatic distance measurement............................................................................................... 13

9. Pinpointing leaks .......................................................................................................................... 16

9.1 Leak pinpointing process ..........................................................................................................................16

9.2 Possible causes of leaks.............................................................................................................................17

9.3 Supercial leak detection.........................................................................................................................17

9.4 Choosing accessories.................................................................................................................................18

9.4.1 Horn (standard attachment) ........................................................................................................18

9.4.2 Focus tube.........................................................................................................................................19

9.4.3 Gooseneck ........................................................................................................................................19

9.4.4 Parabolic mirror...............................................................................................................................20

METPOINT®CID Quick Start Guide

2 | 28

9.5 Selecting sensitivity levels........................................................................................................................21

9.5.1 Sensitivity adjustment button .....................................................................................................21

9.5.2 Auto function (standard)...............................................................................................................22

9.5.3 Manually adjusting the sensitivity..............................................................................................22

9.5.4 Pinpointing leaks.............................................................................................................................22

9.6 Other problems that can make the measurement more dicult....................................................23

9.7 Documenting leaks.....................................................................................................................................25

9.8 Exporting leakage data ..............................................................................................................................26

10. Using the BEKO Leak Management software............................................................................ 26

11. Operation manual....................................................................................................................... 26

12. Notes ........................................................................................................................................... 27

Quick Start Guide METPOINT®CID

3 | 28

1. Safety instructions

1.1 About this document

Carefully read this documentation and familiarize yourself with the product before using it. Observe

all safety instructions and warnings in particular so as to prevent injury and damage to the product.

Keep this documentation within reach so that you will be able to consult it if necessary.

Pass on this documentation to later users of the product.

1.2 General safety instructions

• Use the product properly and exclusively as intended and within the

parameters specied in the technical data. Do not use force.

• Do not, under any circumstance, use the device to measure on or close to live

parts!

• When detecting leaks on electrical systems, please make sure to maintain a

safe distance so as to avoid dangerous electric shock!

• Avoid direct contact with hot or rotating parts.

• Always switch the device on before connecting the headphones! The volume

can be high when the signal levels are high (headphone bars in red range).

1.3 Using Class 2 lasers

• Do not, under any circumstance, point the integrated laser directly at your or

someone else’s eyes! Do not, under any circumstance, hit a person’s or animal’s

eyes with the laser beam!

• Laser module: Conforms to DIN EN 60825-1: 2015-07 Class 2 (< 1 mW)

• Observe the specied storage and operating temperatures.

• Using the device improperly or trying to use force on it will void the warranty.

• Tampering of any kind that is not in conformity with the intended and

described processes will void the warranty and exclude all liability.

• The device is intended exclusively for the purpose described.

1.4 Environmental protection

• Dispose of faulty rechargeable batteries and dead batteries in compliance with

all applicable regulations.

• After this product reaches the end of its service life, dispose of it as

e-waste (in compliance with all local regulations) or return the product to

BEKO TECHNOLOGIES for disposal.

METPOINT®CID Quick Start Guide

4 | 28

2. Intended use

The METPOINT®CID is a leak detection device used to quickly and reliably detect leaks in

compressed air systems.

The METPOINT®CID leak detection device analyses the ultrasonic waves produced by a leak as a

function of distance and pressure.

It is designed exclusively for the intended purpose described here and may only be used accordingly.

The operator must check whether the device is suitable for the use chosen.

The technical data listed on the data sheet are binding.

Inappropriate handling and operation outside the technical specications is not permitted.

Claims of any kind due to non-intended use are excluded.

3. Technical data

Handheld housing dimensions 263 x 96 x 280 mm (11.55 x 3.78 x 11.02 in) with preamplier

and horn

Weight 0.55 kg (1.21 lb) with preamplier and horn.

Approx. 3.0 kg (6.61 lb) for the complete kit in its case

Operating frequency 40 kHz (+/-2 kHz)

Power supply, internal 7.2 V internal lithium-ion battery

Power supply, external 12 VDC 1 A external power supply unit (included)

Operating time > 9 h (continuous operation)

Charging time Max. 4 h

Laser 645 … 660 nm wavelength, output power < 1 mW (Class 2 laser)

Connections 3.5 mm headphone jack for headphones.

Power supply connector for connecting an external charger.

USB port

Colour display Transmissive TFT 3.5” touch panel

Interface USB for importing / exporting data, SW updates, etc.

Data logger 16 GB memory card (Class 4 microSD)

Intended area for use Indoors

Operating temperature -5 °C … +50 °C (+23 … +122 °F)

Storage temperature -20 °C … +60 °C (-4 … +140 °F)

Altitude Up to 4000 m (13,123 ft) above sea level

Max. air humidity < 95% RH, non-condensing

Permissible pollution degree 2

Degree of protection IP20

Quick Start Guide METPOINT®CID

5 | 28

4. Marking

4.1 Type plate

METPOINT®CID

Lithium-Ion-battery: 7,2 V

Power Supply: 12V DC / 1A

Degree of Protection: IP 20

Operating Temperature: -5 … +50°C / +23 ... +122°F

P/N: 4055748

S/N: 42227631

www.beko-technologies.com

4.2 Laser warning label

4.3 Label locations

4.3.1 The METPOINT®CID (standard and laser distance module)

4.3.2 Parabolic mirror

METPOINT®CID

Parabolspiegel / Parabolic mirror

www.beko-technologies.com

P/N: 0530.0106

S/N:

BEKO TECHNOLOGIES GmbH

Im Taubental 7, D - 41468 Neuss

METPOINT®CID Quick Start Guide

6 | 28

5. Device components and controls

Position number Description / Explanation

[1] Release button for preamplier module

[2] 3.5” TFT colour display with touch panel

[3] Membrane keypad (four keys)

[4] ON / OFF button

[5] Volume (+/-)

[6] “Save” key

[7] Connector for power supply unit (battery charging connector)

[8] USB port

[9] Preamplier module

[10] Camera

[11] Horn

Quick Start Guide METPOINT®CID

7 | 28

6. Preparing the device

Before starting the leak detection process, you will need to congure the device. To access the

navigation screens, tap the “Home” button.

6.1 Changing the language

Home -> Settings -> Device Settings -> Set Language -> English

6.2 Checking the current rmware and updating the rmware

Please visit the BEKO TECHNOLOGIES homepage on a regular basis to see if a new rmware version

is available. We are continuously making enhancements and improvements to the product, and

keeping the rmware up to date will ensure that you are using the latest software version and have

access to all available functionalities.

1. Check the rmware version on the homepage and download it from the

following URL: https://www.beko-technologies.com

2. Check the rmware on the METPOINT®CID

Path: Home -> Settings -> About METPOINT®CID -> Software Version

3. If the rmware is outdated, download the new version from the

BEKO TECHNOLOGIES homepage

4. Unzip the ZIP le

5. Copy the unzipped DEV0004 folder to a USB drive

METPOINT®CID Quick Start Guide

8 | 28

The folder structure must look as follows:

6. Plug the USB drive into the METPOINT®CID and connect the power

supply unit

7. Run the system update in:

Path: Home -> Settings -> Device settings -> Update System

8. Tap the “Check USB Stick for new Software updates” button

9. The available update will appear

10. Tap “force all” to run the update

11. Restart the device and update the channels

The device is now updated.

Quick Start Guide METPOINT®CID

9 | 28

6.3 Conguration

Home -> Conguration

You can use the conguration settings to select the system of

units you want and enter the parameters needed in order to

calculate annual leakage costs.

• Select either the ISO or US system of units

• To dene the costs, tap the “Cost / 1000 m3” text eld

• Enter the operating hours per year

(during which the compressed air system is operated

actively)

There are two dierent mode options available for dening

the costs:

• Standard Mode: Cost per 1000 units of volume. The cost

and the currency will need to be entered directly. Default

value:

19 € / 1,000 m³ (0.58 € / 1,000 cf)

• Expert Mode: Can be used to dene the electricity

cost / kWh and the system’s specic power in detail.

The specic power describes the eciency of the compressor

system, i.e., how much electric power (kWh) is required in

order to produce one cubic meter of compressed air (m³).

There are three predened system values for it, as well as a

custom input eld that you can use to enter a dierent value.

In addition, the type of cost can be set in Expert mode. “Electricity cost (70%)” is caused by the

“electric power consumed by” the compressed air system, which typically corresponds to 70% of the

total costs. Meanwhile, “Total Cost (100%)” includes the investment and maintenance costs incurred

in addition to the electricity costs over the compressor’s entire service life.

METPOINT®CID Quick Start Guide

10 | 28

Andere Handbücher für METPOINT CID

Inhaltsverzeichnis

Andere Beko Sicherheitssensor Handbücher

Beko

Beko METPOINT CID Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung