3. Programming Guide
3.1 Detailed Programming Guide：
3.2 To reset to Factory Programming Password（123456）
Step1、Turn off power and connect bin 2&3 of RST(S1)。
Step2、Turn on power and buzzer gives 3 long buzz with green light flash fast。
If need to set Manager Card, now read two empty cards first one as Manager Add Card and
Second one as Manager Delete Card with red light flashing and continuous short buzz .
Step3、Turn off power, disconnect bin2&3 and connect bin 1&2 of RST。
Step4、Turn on power again.
3.3 How to use Manager Card –MAC&MDC
To add a card user in standby mode: read MAC read new cards read MAC
To delete a card user in standby mode: read MDC read registered cards read MDC
To delete all users in standby mode: read MDC read MAC read MDC
Remark: User cards can be added or deleted continuously.
3.4 User ID No. explain
User ID is auto-generating 4-digit number started at 0001. The number increases with adding
user one by one and ignores deleting user. Common Access Password has no ID.
3.5 How to change PIN (When open mode: card+ PIN)
After reading card and input corresponding PIN to open the door, within 5 seconds, long press #
until the green lights flash fast. and then input new PIN # new PIN # , new PIN
changed successfully with a long buzz.
Change Programming Password
#Programming Password #0new Programming Password #
New Programming Password #
If Programming Password lost, perform 3.2 to reset to Factory Default (123456).
#Programming Password #1read card #
If add multiple cards, read cards continuously
Set Common Access Password
#Programming Password #21 new Common Access Password #
Can only enroll one Common Access Password. Open method: Password #
#Programming Password #40 0000 #
Delete all cards and PIN except Common Access Password
#Programming Password #41 read card #
If delete multi cards, read cards continuously
Add Private Access Password(PIN)
#Programming Password #22 PIN #
Can enroll more than 1 PIN, Unlock door method: PIN #
Add card by input card No.
#Programming Password #23 input card No. #
Card No. is 10-digit or 8-digit, machine auto-identify
Add multi-card by input card No. zone
#Programming Password #24 input start card No. card Qty #
Card Qty is 4-digit (If one-time add twenty cards, input 0020)
#Programming Password #3read card PIN #
Delete user by input User ID No.
#Programming Password #42 input User ID No. #
About User ID No. see 3.4
Delete user by input card No.
#Programming Password #43 input card No. #
Card No. is 10-digit or 8-digit, machine auto-identify
#Programming Password #44 input PIN #
#Programming Password #45 1111 #
Use to delete PIN users (Do not include Card users and Card +PIN users)
#Programming Password #5XX #
XX can be 2-digit, and the max. is 99. If input 00, the signal output time is 0.2 Secs.
#Programming Password #6XX #
XX can be 01(only card)/ 02(card or Access Password)/ 03(card+PIN)
Reader setting (Optional)
#Programming Password #604 #
The machine can be used for reader(W26 output)
Security function Setting
Anti-dismantle Alarm setting (Optional)
#Programming Password #7XX #
XX can be 01/ 02( Security function OFF/ON) and 03/04(Anti-dismantle alarm OFF/ON)
Remark: Security Function ON means System would be locked for 5 Minutes if continue to read illegal card or input wrong Access Password for 10 times.
Backlight setting(Optional)
#Programming Password #8XX #
XX can be 01/02/03 (Normal ON / Normal OFF / Auto)
#Programming Password #899 #
Except Programming Password and Manager Card
#Programming Password #91 read MAC read MDC #
First read card is Manager Add Card and Second read card is Manager Delete Card.
Programming Password Default: 123456, all password can be 3~6 digits
