Belden Hirschmann IT MAMMUTHUS MTS26 Series Bedienungsanleitung

Installation MTS2600/2700/2800

Release 01

12/2021

Technical support

https://hirschmann-it-support.belden.com

User manual

Installation

MAMMUTHUS ACCESS LAYER & DISTRIBUTION LAYER

SWITCH

MTS2600/2700/2800 family

MAMMUTHUS POWER MODULE – MTM2700-PSU500/PSU120

MAMMUTHUS MEDIA MODULE – MTM2700-2X

MTS2624-4X-B

MTS2724-4X-FP-S

MTS2724-6X-MP-E

MTS2748-6X-MP-E

Installation MTS2600/2700/2800

Release 01

12/2021

Even if not specifically stated, the copyrighted trademark names in this manual shall not be deemed free of

charge in the sense of the trademark and trade name protection act and thus freely available to anyone.

shall be prohibited from being reproduced, copied, translated or converted into any electronic media or

machine-scannable form, except in the case that you make a copy of the software for your own use.

The performance characteristics described herein shall be binding only upon the express consent of the

parties at the time of signing the contract. This paper is produced by Belden within its capacity. Belden

reserves the right to change the contents of this manual without prior notice. Belden does not guarantee the

correctness or accuracy of the information in this manual.

Belden shall not be liable for damages caused by the use of network components or related operating

software. And the conditions of use specified in the license contract are referred to in this manual.

You may access the latest version of this manual at the product website of Hirschmann IT:

https://catalog.belden.com

Installation MTS2600/2700/2800

Release 01

12/2021

Contents

Safety instructions 7

About this manual 13

Key 14

1 Description 15

1.1 General device description 15

1.2 Device name and product code 20

1.2.1 Basic device 20

1.2.2 Power module 21

1.2.3 Media module 21

1.3 Device view 22

1.3.1 MTS2624-4X-B 22

1.3.2 MTS2724-4X-FP-S 23

1.3.3 MTS2724-6X-MP-E 24

1.3.4 MTS2748-6X-MP-E 25

1.3.5 MTS2824-4X-S 26

1.3.6 MTS2824-6X-E 27

1.3.7 MTS2824F-4X-S 28

1.3.8 MTS2832TF-4X-E 29

1.3.9 MTS2848-6X-E 30

1.3.10 MTS2848-6X-S 31

1.3.11 Power module 32

1.3.12 Media module 33

1.4 Power supply 34

1.5 Ethernet port 35

1.5.1 1000 Mbit/s F/O port 35

1.5.2 10 Gbit/s F/O port 35

1.5.3 10/100/1000 Mbit/s twisted pair port 35

1.5.4 PoE(+) support 35

1.5.5 Out-of-band management port 36

1.6 Display elements 37

1.6.1 Device status 37

1.6.2 Port Status 38

1.7 Management interface 39

1.7.1 DC0 interface (external management) 39

1.7.2 USB interface 39

2 Installation 40

4 Installation MTS2600/2700/2800

Release 01

12/2021

2.1 Checking the package contents 40

2.2 Installing the power module (optional) 40

2.2.1 Installing the power module 40

2.3 Installing and grounding the device 41

2.3.1 Installing the device in a switch cabinet 41

2.3.2 Installing the device on a vertical flat surface 44

2.3.3 Grounding the device 45

2.4 Installing the SFP transceiver (optional) 46

2.5 Operating the device 47

2.6 Connecting the data cables 47

2.7 Filling out the inscription Label 48

3 Making basic settings 49

4 Monitor ambient air temperature 50

5 Maintenance and repair 51

6 Disassembly 52

6.1 Removing the power module 52

6.2 Removing the media module 52

6.3 Removing the SFP transceiver 53

6.4 Removing the device 54

6.4.1 Removing the device from a vertical flat surface 54

6.4.2 Removing the device from the switch cabinet 54

7 Technical data 55

7.1 General technical data 55

7.2 Dimension drawing 57

7.3 EMC and immunity 70

7.4 Network range 73

7.5 Power consumption / power output 74

8 Scope of delivery, order number, and accessories 75

9 Underlying technical standards 77

A Further support 78

Installation MTS2600/2700/2800

Release 01

12/2021

DANGER draws attention to an immediately dangerous situation, which

will

inevitably

result in a serious or fatal accident if not observed.

DANGER

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION indicates a possible danger which, if not avoided, may result in

minor injuries.

Important Information

Note: Read these instructions carefully, and familiarize yourself with the

device before trying to install, operate, or maintain it. The following notes

may appear throughout this documentation or on the device. These notes

warn of potential hazards or call attention to information that clarifies or

simplifies a procedure.



Symbol explanation

This is a general warning symbol. This symbol alerts you to

potential personal injury hazards. Observe all safety notes that

follow this symbol to avoid possible injury or death.

If this symbol is displayed in addition to a safety instruction of

the type “Danger” or “Warning”, it means that there is a danger

of electric shock and failure to observe the instructions will

inevitably result in injury.

This symbol indicates the danger of hot surfaces on the

device. In connection with safety instructions, non-observance

of the instructions will inevitably result in injuries.

WARNING

CAUTION

6 Installation MTS2600/2700/2800

Release 01

12/2021

NOTICE provides information about procedures that do not involve the risk

of injury.

NOTICE

Installation MTS2600/2700/2800

Release 01

12/2021

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

device damage.

Safety instructions



General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.



Before connecting any cable, read this document, and the safety

instructions and warnings.



Operate the device with undamaged components exclusively.



The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann IT for inspection.



Qualification requirements for personnel



Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:



Qualified personnel are properly trained. Training as well as

practical knowledge and experience make up their qualifications.

This is the prerequisite for grounding and labeling circuits,

devices, and systems in accordance with current standards in

safety technology.



Qualified personnel are aware of the dangers that exist in their

work.



Qualified personnel are familiar with appropriate measures

against these hazards in order to reduce the risk for themselves

and others.

WARNING

8 Installation MTS2600/2700/2800

Release 01

12/2021

The following requirements apply without restrictions:



Qualified personnel receive training on a regular basis.



Correct usage

Only use the device for those purposes specified in the catalog and in

the technical description. Only operate the device with external devices

and components that are recommended and permitted by the

manufacturer. The proper and safe operation of this product depends

on proper handling during transport, proper storage, assembly and

installation, and conscientious operation and maintenance procedures.



National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.



Ensure the integrity and consistency

Check the bond on the packaging to assure it is sealed and not

tampered by unauthorized party.

Verify serial number of delivered products to make sure it is unified

with a hardcopy serial number list provided by manufacturer. If it is

necessary, please contact Belden representative to obtain a

softcopy serial number list from manufacturer for double check.



Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.



The electrical wires are voltage-free.



The cables used are permitted for the temperature range of the application case.



Connect the ground screw on the back of the device to the protective conductor before

setting up other connections. When to remove connections, the protective conductor is

the last to be removed.



Exclusively switch on the device when it is installed.



Relevant for North America:

Use 60 °C / 75 °C (140 °F / 167 °F) or 75 °C (167 °F) copper (Cu) wires only.

Table 1: Requirements for connecting electrical wires

Installation MTS2600/2700/2800

Release 01

12/2021

The following requirements apply without restrictions:



Requirements for connecting the supply voltage

All variants All of the following requirements are complied with:



The supply voltage corresponds to the voltage specified on the type

plate of the device.



The power supply conforms to overvoltage category I or II.



The power supply has an easily accessible disconnecting device (for

example a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.



When to connect a power supply voltage with a protective conductor:

first connect the protective conductor, and then the power supply

voltage. If the device contains such a second power supply voltage

connection module: first connect the protective conductor, and then

the power supply voltage.



Supply with DC voltage: The wire diameter of the power supply cable

is at least 1 mm² (North America: AWG16) on the supply voltage

input.



Supply with AC voltage: The wire diameter of the power supply cable

is at least 0.75 mm² (North America: AWG18) on the supply voltage

input.



The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.



The power supply cable is suitable for the voltage, the current and

the physical load.

Table 2: Requirements for connecting the supply voltage



Shield grounding

The overall shield of a connected shielded twisted pair cable is

connected to the grounding connector on the rear panel as a

conductor.

Beware of possible short circuits when connecting a cable section

with conductive shielding braiding.



Safe grounding

Make sure you ground the devices assembled in the switch cabinet

safely. In particular, check the supply voltage connections if they are

not connected directly to the supply cable (for example, when using

power strips).

10 Installation MTS2600/2700/2800

Release 01

12/2021



ESD guide

These modules are equipped with electrostatic sensitive

components.

If the connection is touched, these sensitive components may be

damaged or their service life shortened by electric field or charge

balance effects. You may find information about electrostatic hazard

components in DIN EN 61340-5-1 (2007-08) and DIN EN 61340-5-2

(2007-08).



Device casing

Only technicians authorized by the manufacturer are allowed to open

the enclosure.

Keep the cooling fins free to ensure good air circulation.

Verify that there is at least 10 cm (4 in) of space around the cooling

fins of the casing.

Do not touch the housing during operation or shortly after switching

off the device. Hot surfaces can cause injury.

Install the device horizontally in the cabinet or vertically on a flat

surface. Operating the device as a table unit is inadmissible.

See installing and grounding the device on Page 41.

Operate the device at the maximum ambient air temperature and in

stacking: when to install the device, confirm that there is at least

one available rack space that is approximately 5 cm (2 in) above the

device to allow heat to escape through the enclosure of the device.

If you operate the device in a 19ʺswitch cabinet: install the slide /

rails to support the weight of the device.



Installation site requirements

Operate the device at the specified ambient temperature (temperature

of the ambient air at a distance of 5 cm (2 in) from the device) and at

the specified relative humidity exclusively.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Increased ambient temperature: When you are operating the device

in a closed switch cabinet or together with other devices in a switch

cabinet, the ambient temperature in the switch cabinet can be

higher than the ambient temperature in the room. Only install the

device in an ambient temperature in line with the maximum ambient

temperature specified by the manufacturer: tmax.

Mechanical stress: Install the device in a switch cabinet in such a

way that rules out hazardous conditions due to severe mechanical

stress.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden grass valley GV FABRIC Bedienungsanleitung

Belden

Belden Thinklogical TLX48 Bedienungsanleitung

Belden

Belden HIRSCHMANN BRS20 Bedienungsanleitung

Belden

Belden Hirschmann MACH104-PoEP Series Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Belden

Belden Hirschmann MACH1040 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN PTN-CSM310-A Bedienungsanleitung

Belden

Belden HIRSCHMANN RSPE 30 Bedienungsanleitung

Belden

Belden HIRSCHMANN GRS105 Bedienungsanleitung

Belden

Belden MAMMUTHUS MTM2800-PSU120 Bedienungsanleitung

Belden

Belden HIRSCHMANN OCTOPUS OS24 Series Bedienungsanleitung

Belden

Belden Hirschmann RS20 U Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 4000 Series Bedienungsanleitung

Belden

Belden Hirschmann HiOS-2S Bedienungsanleitung

Belden

Belden Hirschmann RED25 Series Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden HIRSCHMANN OCTOPUS OS20 Series Bedienungsanleitung

Belden

Belden Hirschmann MACH1000 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH4002-48+4G Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Bedienungsanleitung

Belden

Belden Hirschmann SPIDER 8TX EEC Handbuch

Belden

Belden Hirschmann MACH104 Series Benutzerhandbuch

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch