Belden Hirschmann BAT867-F Bedienungsanleitung

Installation BAT867-F

Release

12/2019

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Access-Point / Client / Access-Bridge

BAT867-F

2019-12-18 Installation BAT867-F

Release

12/2019

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation BAT867-F

Release

12/2019 3

Contents

Safety instructions 5

About this manual 15

Key 16

1 Description 17

1.1 General description 17

1.2 Device name and product code 18

1.3 Device view 20

1.4 Power supply 20

1.4.1 Supply voltage with the characteristic value W

(24 V DC) 20

1.4.2 Supply voltage with the characteristic value P (Power

supply only through PoE) 21

1.5 Ethernet port 21

1.5.1 10/100/1000 Mbit/s PoE port 21

1.5.2 Pin assignments 22

1.6 Connections for antennas 23

1.7 Display elements 23

1.7.1 Device state 23

1.8 Reset button 24

2 Installation 25

2.1 Checking the package contents 25

2.2 Installing and grounding the device 25

2.2 Mounting the device 25

2.2.2 Grounding the device 26

2.3 Installing the antennas 27

2.4 Connecting the power supply 27

2.5 Operating the device 28

2.6 Connecting data cables 28

3 Making basic settings 30

4Installation BAT867-F

Release

12/2019

4 First login (Password change) 31

5 Obtain compliance for operation in the European

Union 32

6 Configuring the transmit power 35

7 Monitoring the ambient air temperature 37

8 Maintenance and service 38

9Disassembly 39

10 Technical data 40

10.1 General technical data 40

10.2 Dimension drawings 41

10.3 Radio technology 42

10.4 Roaming 42

10.5 Receiving sensitivity, transmit power and data rate 43

10.5.1 IEEE 802.11b 43

10.5.2 IEEE 802.11g 43

10.5.3 IEEE 802.11a 44

10.5.4 IEEE 802.11n 44

10.5.5 IEEE 802.11ac 46

10.6 EMC and immunity 47

10.7 Network range 48

10.8 Power consumption/power output 48

11 Scope of delivery, order numbers and

accessories 49

12 Underlying technical standards 51

A Further support 52

Installation BAT867-F

Release

12/2019 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 40.

Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

6Installation BAT867-F

Release

12/2019

Installation site requirements

Use the device only indoors.

Restricted access location:

The location is outside the operator access area.

The location is accessible to the service personnel even when the

device is switched on.

Indoor operator access area:

The location is accessible without tools.

The person responsible for the area has provided access for the

operator intentionally.

The operator knows of the access possibilities, regardless of whether

they need a tool.

Relevant for Europe:

Supply only 24 V DC to the device and use a fuse.

Regarding the properties of this fuse: See “General technical data”

on page 40.

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 40.

Mount the device in the vertical position.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Installation BAT867-F

Release

12/2019 7

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

When installing antennas, observe the regulations of the country in

which you are operating the WLAN device with regard to the general

operating permission and the maximum emission levels.

Install and operate this equipment with a minimum distance of

19.7 inches (50 cm) between the antenna and your body.

Grounding the device

For the functional earth (FE), there is a separate functional earth screw on

top of the device. The functional earth is electrically connected to the

circuit ground and the metal housing of the device.

Shielding ground

The overall shield of a connected shielded twisted pair cable is connected

to the grounding connector on the front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

8Installation BAT867-F

Release

12/2019

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

The connected voltage complies with the requirements for a safety extra-low voltage

(SELV) or ES1 as per IEC/EN 62368-1.

Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Table 1: Requirements for connecting electrical wires

Installation BAT867-F

Release

12/2019 9

Requirements for connecting the supply voltage

The supply voltage is connected to the device casing through protective

elements exclusively.

The following requirements apply without restrictions:

All of the following requirements are complied with:

The supply voltage corresponds to the voltage specified on the type plate of the

device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (for example a

switch or a plug). This disconnecting device is clearly identified. So in the case of an

emergency, it is clear which disconnecting device belongs to which power supply

cable.

The power supply cable is suitable for the voltage, the current and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm² (AWG20 up to

AWG18).

The cross-section of the ground conductor is the same size as or bigger than the

cross-section of the power supply cables.

The following requirements apply alternatively:

Alternative 1 The power supply complies with the requirements for a limited power

source (LPS) as per IEC/EN 60950-1 or IEC/EN 62368-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements according to

NEC Class 2.

Alternative 3 All of the following requirements are complied with:

The power supply complies with the requirements for a safety extra-

low voltage (SELV) or ES1 as per IEC/EN 62368-1.

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is also

located in the minus conductor.

Regarding the properties of this fuse:

See “Technical data” on page 40.

Table 2: Requirements for connecting the supply voltage

10 Installation BAT867-F

Release

12/2019

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/53/EU (RED)

Directive of the European Parliament and of the council on the

harmonization of the laws of the Member States relating to the making

available on the market of radio equipment.

This product may be operated in all EU (European Union)

countries under the condition that it has been configured correctly.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be available to the relevant authorities at the following

address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The product can be used in residential areas (residential, commercial and

light-industrial environments) and in industrial areas.

Interference immunity: EN 61000-6-1

Emitted interference: EN 55032

Safety: EN 62368-1

You find more information on technical standards here:

“Underlying technical standards” on page 51

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

Inhaltsverzeichnis

Andere Belden Drahtloser Zugangspunkt Handbücher

Belden

Belden Hirschmann BAT-F Series Bedienungsanleitung

Belden

Belden HIRSCHMANN BAT450-F Bedienungsanleitung

Belden

Belden HIRSCHMANN IT Dragonfly Series Bedienungsanleitung

Belden

Belden Hirschmann BAT-F Bedienungsanleitung

Belden

Belden Hirschmann BAT867-R Bedienungsanleitung

Belden

Belden HIRSCHMANN IT Dragonfly DAP620 Bedienungsanleitung

Belden

Belden Hirschmann OpenBAT BAT-R Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung