Belkin F5U011 Bedienungsanleitung

P52784

USB

Ethernet Adapter

User Manual

F5U011

USB

Ethernet Adapter

WARRANTY AND LICENSE

Belkin Components warrants this product to be free from defects in material,

content, and workmanship for life. If a defect is discovered, Belkin will, at its option,

repair or replace the product at no charge. Proof of purchase may be required.

The CATC software is licensed for use on a single PC. The software may be copied

for backup purposes only.

This warranty covers all defects in material or workmanship. It does not cover

accidents, misuse, neglect, unautho-rized product modification, or acts of nature.

Belkin Components shall not be liable for damage to other property caused by any

defects in this product, damages based upon inconvenience, loss of use of the

product, loss of time or data, commercial loss, or any other damages, whether

incidental, consequential, or otherwise.

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. If this equipment does cause harmful

interference to radio or television reception, the user will be responsible to correct

the interference at his own expense.

Note 1: Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Note 2: Shielded interface cables must be used in order to comply with the emissions

limits.

Contactng Belkin Components

Sales 310.898.1100

Technical Support 310.898.1100 ext.2263

Web Site www.belkin.com

E-mail [email protected]

[email protected]

manual may be copied, photocopied, reproduced, translated, or reduced to electronic

medium or machine-readable form without prior written consent from Belkin

Components.

TABLE OF CONTENTS

1. Introduction 1

2. USB Ethernet Adapter 2

2.1 Supplied Components 2

2.2 System Setup 2

2.3 In addition… 2

2.4 Supplied Software

2.5 Cable Connections 2

3. Installation (SETUP.EXE) 5

3.1 Automatic Installation

For Windows®98 System 6

4. Specifying the TCP/IP Parameters 7

5. Uninstalling Procedures 8

6. Troubleshooting 8

7. Specifications 10

1. INTRODUCTION

Thank you for purchasing Belkin Components' USB Ethernet Adapter. Now, you can

easily connect any USB-equipped notebook, portable, or desktop computer to an Ethernet

local area network. The product consists of a small plastic enclosure incorporating both

USB and 10Base-T (RJ45 TP) Ethernet ports, plus the associated software.

Windows®applications that communicate via an Ethernet card will also work with the

Belkin USB Ethernet Adapter. It offers a Plug-and-Play solution for network connectivity,

eliminating the need to insert cards or shut down the system at connection time.

Our adapter conforms to both USB and Ethernet specifications, and functions as a full-

speed USB device. In addition, the hardware includes an Ethernet controller, appropriate

memory buffers, and on-board non-volatile memory for network configuration. The unit

requires no external power supply; it is powered directly by the Universal Serial Bus.

The provided software supports the Windows®98 operating system environments. The

CATC software drivers provide a bridge between the existing network layer protocols and

the USB protocol stack, hiding the details of the USB interface from the application

programs. This manual explains how to connect and use the Belkin USB Ethernet Adapter

hardware and software with your PC and network environment.

USB

Ethernet Adapter

2. BELKIN USB ETHERNET ADAPTER

2.1 Supplied Components

The following components are included:

• Belkin USB Ethernet Adapter device

(Specifications are outlined in Section 7.)

• Belkin USB cable, 6'

• Software installation diskette

• Belkin USB Ethernet Adapter User Manual (this manual)

2.2 System Setup

Our adapter works with any computer that has a standard USB port. The USB

line powers the adapter directly; an additional power supply is not required.

The USB cable is provided; you provide the network cable.

Caution: If you choose to use a USB hub, the hub must be externally powered.

You cannot use a bus-powered hub.

In order to use the adapter, you must install drivers in the USB host PC, as

described in the following sections. In addition, you need to configure the

network parameters.

2.3 In addition...

You will need a network (Ethernet) cable, and your original Windows®98 CD.

You should be familiar with using Microsoft Windows®folders, dialogs, and

forms. If you need to review this information, consult your Microsoft Windows®

documentation.

You should be familiar with your required network configuration procedures

and how to specify valid IP addresses and Subnet Masks.

2.4 Supplied Software

The software installation diskette contains all of the installation and utility files

required for the USB Ethernet Adapter.

2.5 Cable Connections

Figure 2-1 illustrates the provided USB cable connection from the PC

(rectangular Series A connector) to the adapter (square Series B connector), and

a standard 10Base-T Ethernet cable connection from the RJ45 connector on the

adapter to an Ethernet port. Make connections as illustrated below, when

requested in the installation procedure.

Figure 2-1. Basic PC-to-Ethernet Port Connections

This document makes several references to an Ethernet port, used to connect the

adapter to an Ethernet environment. Such a port might be an Ethernet hub,

network wall socket, peripheral device, etc.

USB Ethernet Adapter

Figures 2-2, 2-3, and 2-4 illustrate sample applications for the Belkin USB

Ethernet Adapter.

Figure 2-2. PC-to-PC Direct Connections

Ethernet Cross Cable

Ethernet Hub

Figure 2-3. PC-to-Ethernet Network Connections

USB Ethernet Adapter

3. INSTALLATION (SETUP.EXE)

This section outlines the quick and easy, automatic installation procedure for the

USB Ethernet Adapter drivers.

Note: The installation program automatically detects if your computer is

properly configured and initialized for USB installation. If the installation

program aborts, see the Troubleshooting section. You may need to upgrade your

computer. Make connections when requested in the installation procedure,

illustrated in Figure 2-1.

Your particular environment may require drive letters or folder names different

than those mentioned here. You may be asked to specify file locations on the

Windows®CD, or on the software installation diskette. For example:

– Windows®might look on the A:\ drive for a file that is on the Windows®98

CD. In this case, you would specify a search such as D:\WIN98\SETUP.

ASYNC

RESET

POWER

CABLE

Modem

Figure 2-4. PC-to-Cable Modem Connections

Cable

USB Ethernet Adapter

3.1 Automatic Installation For Windows®98 System

The installation procedure assumes that this is a new driver installation on a

Windows®system. The installation program automatically recognizes if your

operating system is Windows®98.

1. Close any Windows®applications that may be running on your computer.

2. Insert the software installation diskette in the appropriate drive.

3. Connect the USB cable to your computer. Do not connect the USB cable to the

adapter.

4. Connect the network cable to the network port and to the Ethernet Adapter.

5. From the Windows®Taskbar, select Start / Run.

6. In the Run dialog, type A:\SETUP.

7. Click OK.

The system displays Setup and Welcome screens.

8. Click Next.

9. Read the on-screen messages. Make the connection as requested.

10. A New Hardware Found form appears with the message: USB Ethernet Adapter.

The system builds the driver information database and completes the installation.

During this process, you may be asked to load the Microsoft Windows®98 CD, and

to reload the software installation diskette, as necessary. When complying with these

instructions, you can safely close any auto-display window that appears following a

CD insertion.

11. Click Finish.

12. Read, then close, the Notepad message confirming the installation. It describes the

requirements for configuring the appropriate Ethernet connections and specifying

the TCP/IP (or other) protocol parameters. Turn to Section 4 in this manual for

additional information.

4. SPECIFYING THE TCP/IP PARAMETERS

This configuration procedure is identical to that of other network interfaces, for

example, an Ethernet card. The following sections describe two basic setups

using the TCP/IP protocol.

A. When the Belkin USB Ethernet Adapter is the only installed network interface.

Select My Computer / Control Panel / Network.

The Network Configuration form appears. In this form, the USB Ethernet

Adapter icon should be visible.

Additionally, a new protocol icon with the title TCP/IP should be visible. To

specify the TCP/IP parameters, use the procedures described in section C below.

B. When another network interface is already installed in the system.

Select My Computer / Control Panel / Network.

The Network Configuration form appears. In this form, the USB Ethernet

Adapter icon should be visible.

If the TCP/IP protocol was previously installed, a network connection icon with

the title TCP/IP -> USB Ethernet Adapter should also be visible. To specify the

TCP/IP parameters, use the procedures described in sections C below.

C. To specify the TCP/IP parameters for New Networks:

1.Select TCP/IP, (or TCP/IP -> USB Ethernet Adapter, if more than one network

interface is installed).

2.Click Properties.

3.Select Specify an IP Address.

Note: If you are connecting to an existing network, please see your system administrator for

this information. If you are setting up a new network, we recommend the following:

Suggested IP Address = 194 . 168 . 0 . "X"

(where "X" is greater than 0 and less than 255).

Suggested Subnet Mask = 255 . 255 . 255 . 0

4.Enter a valid IP Address and Subnet Mask.

5.Click OK.

6.Select the Identification tab and verify / modify the computer name and

workgroup.

7.Click OK.

You will see the option to restart your computer if you made changes.

8.Remove any diskette that might be in the floppy drive.

9.Click Yes to restart the computer.

Inhaltsverzeichnis

Andere Belkin Adapter Handbücher

Belkin

Belkin F7D2102 Bedienungsanleitung

Belkin

Belkin 802.11g Wireless Ethernet Bridge Bedienungsanleitung

Belkin

Belkin F8T031 - Bluetooth Wireless USB Printer Adapter Print... Bedienungsanleitung

Belkin

Belkin F8Z452ea Bedienungsanleitung

Belkin

Belkin F8T008 Bedienungsanleitung

Belkin

Belkin F6D4050 Bedienungsanleitung

Belkin

Belkin F4U047-RS Bedienungsanleitung

Belkin

Belkin Powerline AV Networking Adapters Bedienungsanleitung

Belkin

Belkin F5U003 Bedienungsanleitung

Belkin

Belkin F5U512-MAC Bedienungsanleitung

Belkin

Belkin F5U122-PC Bedienungsanleitung

Belkin

Belkin F5U104 Bedienungsanleitung

Belkin

Belkin F8T001 Bedienungsanleitung

Belkin

Belkin MIRACAST VIDEO ADAPTER Bedienungsanleitung

Belkin

Belkin F9L1101 Bedienungsanleitung

Belkin

Belkin F8T001 Bedienungsanleitung

Belkin

Belkin Wireless Gplus Notebook Card Bedienungsanleitung

Belkin

Belkin F5D4075 - Powerline AV+ Starter Bedienungsanleitung

Belkin

Belkin F5D7051 Bedienungsanleitung

Belkin

Belkin F5U002 Leitfaden

Belkin

Belkin USB/SCSI Adapter F5U115-UNV Bedienungsanleitung

Belkin

Belkin F5D4078 Bedienungsanleitung

Belkin

Belkin F5D4073 Bedienungsanleitung

Belkin

Belkin F8Z452ea Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung