Belkin F5U111 Bedienungsanleitung

DECLARATION OF CONFORMITY WITH FCC RULES FOR

ELECTROMAGNETIC COMPATIBILITY

We, Belkin Components, of 501 West Walnut Street, Compton

CA 90220, declare under our sole responsibility that the product:

Belkin Components F5U111

to which this declaration relates:

Complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

CE Declaration of Conformity

We, Belkin Components, declare under our sole responsibility

that the Belkin Components F5U111

to which this declaration relates, is in conformity with General

Emissions Standard EN50081-1 and with Generic Immunity

Standard EN50082-1 1992.

Belkin Components

501 West Walnut

Compton • CA • 90220-5221

Phone 800.2BELKIN (223.5546)

310.898.1100

Fax 310.898.1111

Belkin Components, Ltd.

13 Gatelodge Close

Round Spinney • Northampton • NN3 8RX

Phone +44 (0) 1604678300

Fax +44 (0) 1604678330

www.belkin.com

usb.belkin.com

USB Ethernet Adapter

User Manual

F5U111

P73311

WARRANTY AND LICENSE

Belkin Components warrants this product to be free from defects in

material, content, and workmanship for life. If a defect is discovered,

Belkin will, at its option, repair or replace the product at no charge.

Proof of purchase may be required.

The CATC software is licensed for use on a single PC. The software

may be copied for backup purposes only.

This warranty covers all defects in material or workmanship. It does not

cover accidents, misuse, neglect, unauthorized product modification, or

acts of nature. Belkin Components shall not be liable for damage to

other property caused by any defects in this product, damages based

upon inconvenience, loss of use of the product, loss of time or data,

commercial loss, or any other damages, whether incidental,

consequential, or otherwise.

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. If this equipment does cause

harmful interference to radio or television reception, the user will be

responsible to correct the interference at his own expense.

Note 1: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Note 2: Shielded interface cables must be used in order to comply with

the emissions limits.

Contacting Belkin Components:

Sales 310.898.1100

Technical Support 310.898.1100 ext.2263

Web Site www.belkin.com

E-mail [email protected]

[email protected]

copied, photocopied, reproduced, translated, or reduced to electronic medium or machine-readable

form without prior written consent from Belkin Components.

Warranty and License

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. USB Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2.1. Ethernet Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2.2. Supplied Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.3. System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.4. Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3. Installation (SETUP.EXE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.1 Automatic Installation for Win®98 . . . . . . . . . . . . . . . . . . . . .7

4. Specifying the TCP/IP Parameters . . . . . . . . . . . . . . . . . . . . . . .8

5. To Unintall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

6. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

7. Warranty and License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Table of Contents

Thank you for purchasing the Belkin Components USB Ethernet

Adapter. Now, you can easily connect any USB-equipped notebook,

portable, or desktop computer to an Ethernet local area network.

Windows®applications that communicate via an Ethernet card will also

work with the Belkin USB Ethernet Adapter. It offers a Plug-and-Play

solution for network connectivity, eliminating the need to insert cards or

shut down the system at connection time.

Our adapter conforms to both USB and Ethernet specifications, and

functions as a full-speed USB device. The unit requires no external

power supply; it is powered directly by the Universal Serial Bus.

The provided software supports the Windows®98 operating system

environments. This manual explains how to connect and use the Belkin

USB Ethernet Adapter hardware and software with your PC and

network environment.

1. Introduction

Consult the appropriate Windows

documentation, or contact your System

Administrator.

Remove and reinstall the USB support

component of the operating system.

Use the Windows

Find Computer option.

Be patient when reconnecting a USB device.

Wait at least 20 seconds between

disconnecting and connecting devices.

Be patient when Windows

is installing the

Adapter (or any other USB device).

Plug-and-Play operations in Windows

can

sometimes take up to 30 seconds or so

between apparent activities.

You require additional information about

adding or removing network drivers.

The system does not respond when

connecting the Adapter (for example, the

hourglass cursor remains on the screen).

You cannot find the other computer (on the

Ethernet side of the network connection).

When reconnecting the USB device, the

system seems to take a long time.

The system installation appears to be slow.

6. Troubleshooting

You replaced the Ethernet Adapter with a

new Ethernet Adapter and it does not work.

The installation procedure produces the

message: Hardware and software support

for USB was not found.

The LED is off.

The LED is blinking.

Each Belkin USB Ethernet Adapter has a

unique encoded Ethernet identifier.

Unplugging the adapter from the Windows

machine, and plugging a different adapter

into the same port, will cause a problem in

the protocol software. The original device

should first be completely uninstalled.

The program detected that your computer is

not configured for proper USB support. There

are four main conditions to check:

1. You do not have a USB connection on the

motherboard. The solution is to upgrade your

motherboard or add a USB controller card.

2. It is possible that you do have the proper

OS, but there is no connection between the

motherboard and the USB connectors on the

bracket.

3. It is possible that you do have the proper

OS, but the controller on the motherboard is

malfunctioning.

There are two main possibilities:

1. The host computer might be in standby

mode, and not supplying full power to its

devices.

2. The Ethernet Adapter did not properly

enumerate. Enumerate is a USB term

meaning the system has identified and

configured the device and given it a unique

address.

The Ethernet port connection might be

inoperable. Check the Ethernet connection.

Replace the Ethernet cable.

2.1. Ethernet Adapter

Package

Dimensions: 4.25 X 3.75 X 1.25

Connector (Ethernet): RJ45

Connector (USB): Series B

Weight: 3.9 oz.

Power Requirements:

5 V, 200 mA (powered via the USB connection)

Data Transfer Rate

Can exceed 6 Mbits/s (depending on the computer, operating

system, and communication protocol)

Environmental Conditions

Operating Range: 0 to 55 °C (32 to 131 °F)

Storage Range: -20 to 80 °C (-4 to 176 °F)

Humidity: 10 to 90%, non-condensing

LED

Flashes when the USB connection is operational.

Remains steady on when both the USB and Ethernet

connections are active.

Memory Size

32K ( 8-bit SRAM for IN and OUT data buffers

1024-bit non-volatile configuration storage

Certification

FCC, Class B

CE Mark

Software Compatibility

The Belkin Ethernet Adapter works with any standard Ethernet

protocol. The supplied drivers for Microsoft Windows®98 and

Windows®95 (OSR2.1) support the following protocols: TCP,

IPX, and NetBEUI.

2. USB Specifications

2.2 Supplied Components

The following components are included:

• Belkin USB Ethernet Adapter device

(Specifications are outlined in Section 7)

• Belkin USB cable, 6'

• Software installation diskette

• Belkin USB Ethernet Adapter User Manual

2.3 System Setup

The USB cable is provided; you provide the network cable.

Caution: If you choose to use a USB hub, the hub must be

externally powered. You cannot use a bus-powered hub.

In order to use the adapter, you must install drivers in the USB host

PC, as described in the following sections. In addition, you need to

configure the network parameters.

You will need a network (Ethernet) cable, and your original

Windows®98 CD.

2.4 Cable Connections

Figure 2-1 illustrates the provided USB cable connection from the

PC (A connector) to the adapter (B connector), and a standard

10Base-T Ethernet cable connection from the RJ45 connector on

the adapter to an Ethernet port. When prompted in the installation

procedure follow any of the following connections:

USB Specifications

than one network interface is installed).

2. Click Properties.

3. Select Specify an IP Address.

Note: If you are connecting to an existing network, please see your

system administrator for this information. If you are setting up a new

network, we recommend the following:

Suggested IP Address = 194 . 168 . 0 . "X"

(where "X" is greater than 0 and less than 255).

Suggested Subnet Mask = 255 . 255 . 255 . 0

4. Enter a valid IP Address and Subnet Mask.

5. Click OK.

6. Select the Identification tab and verify / modify the computer

name and workgroup.

7. Click OK. You will see the option to restart your computer if you

made changes.

8. Remove any diskette that might be in the floppy drive.

9. Click Yes to restart the computer.

5. TO UNINSTALL

If you wish to remove the Belkin USB Ethernet Adapter component

from your computer, do the following:

1. Disconnect the USB cable from the adapter.

2. Select My Computer/Control Panel/Add/Remove Programs.

3. In the Install/Uninstall tab, select USB Ethernet Adapter.

4. Click Add/Remove.

5. Click Yes.

The software program will be automatically removed by Windows®.

6. TROUBLESHOOTING

PROBLEM SUGGESTED SOLUTION / COMMENTS

5. Uninstall

Inhaltsverzeichnis

Andere Belkin Adapter Handbücher

Belkin

Belkin F5D8073 Bedienungsanleitung

Belkin

Belkin F1PG200ENau Bedienungsanleitung

Belkin

Belkin VideoBus II F5U208-MAC Bedienungsanleitung

Belkin

Belkin Headphone Adapter Bedienungsanleitung

Belkin

Belkin USB Wireless Adapter Bedienungsanleitung

Belkin

Belkin Bluetooth USB Adapter F8T012 Bedienungsanleitung

Belkin

Belkin USB/SCSI Adapter F5U115-UNV Bedienungsanleitung

Belkin

Belkin F8T001 Bedienungsanleitung

Belkin

Belkin F6D6050v1 Bedienungsanleitung

Belkin

Belkin AC Wi-Fi Bedienungsanleitung

Belkin

Belkin SURF N300 Bedienungsanleitung

Belkin

Belkin F5U109 Bedienungsanleitung

Belkin

Belkin F5D4072 Bedienungsanleitung

Belkin

Belkin F5D4075 - Powerline AV+ Starter Bedienungsanleitung

Belkin

Belkin F5D6050 Referenzhandbuch

Belkin

Belkin F5D8051 Bedienungsanleitung

Belkin

Belkin SOUNDFORM CONNECT AUZ002 Bedienungsanleitung

Belkin

Belkin F5L014 Bedienungsanleitung

Belkin

Belkin Gigabit Powerline HD Networking Adapter Bedienungsanleitung

Belkin

Belkin F5L043-DL Bedienungsanleitung

Belkin

Belkin F7D4555 Bedienungsanleitung

Belkin

Belkin F5U120-PC Bedienungsanleitung

Belkin

Belkin F5D7330 Montage- und Wartungsanleitung

Belkin

Belkin F5D7051 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung