Bellman & Symfon BE9026 Bedienungsanleitung

Buttons and connections

Visit telephone transmitter

Test / program buttons

2.5 mm ext. trig.

Pre-mounted telephone cord

BE9251 Mobile phone sensor

Doorbell push button

3.5 mm ext. trig. BE9023 Magnetic switchBE9026 Contact matLED lights

BE9253

BE1431

In the box

BE1431 Visit telephone transmitter

2

¯1.5 V AA alkaline batteries

Telephone cord and adapter

Screw and wall plug

Power and battery

Battery power

2¯1.5 V AA lithium or alkaline

type batteries

Power consumption

Active < 70 mA

Idle position < 15 μA

Operation time

Alkaline batteries ~ 5 years

Lithium batteries ~ 10 years

Accessories

BE9251 Mobile phone sensor

BE9023 Magnetic switch

BE9026 Contact mat

BE9253 Ext. trig. cable, 3.5 mm

Inputs

RJ11 analogue telephone input

2.5 mm external trigger input

3.5 mm external trigger input

Frequency and coverage

Frequency: 314.91 MHz, 433.92 MHz

or 868.30 MHz, depending on region

Coverage: 50 - 250 m, 55 - 273 yd.

depending on the radio frequency

and the building’s characteristics

Dimensions and weight

Height: 100 mm, 4.0"

Width: 65 mm, 2.6"

Depth: 27 mm, 1.1"

Weight: 120 g, 4.2 oz. incl. batteries

Activation

The test buttons

A landline telephone

A smartphone or tablet via the

mobile phone sensor

A contact mat or magnetic switch

A doorbell connected to the ext trig

Environment

For indoor use only

Technical specications

Using a mobile phone

1 Use for instance a mobile phone to call the landline

telephone. The top LED on the transmitter lights up in

green to show that an incoming call is detected.

2 The yellow Visit LED on the receiver lights up to show

that the radio signal was received. In addition, it starts to

sound, ash or vibrate depending on the receiver.

Note: If you have changed the signal pattern, it will react

in accordance with the table on the following spread.

Setting up the transmitter

1Remove the battery pull tab to start the unit.

Clean the wall with the wet wipe and remove the protective lm from the Velcro.

2Mount the transmitter on the wall. You can also use the supplied screw and plug.

3Connect the telephone adapter as shown below.

Note: The appearance of the adapter may dier with territory.

1 2

Testing the connection

Using the test button

1 Press both test buttons simultaneously on the telephone

transmitter. The top LED lights up in green to show that

a radio signal is being transmitted.

2 The yellow Visit LED on the receiver lights up to show

that the signal was received. In addition, it starts to

sound, ash or vibrate depending on the receiver.

Note: If you have changed the signal pattern, it will react

in accordance with the table on the following spread.

1 2 1 2

Visit telephone transmitter

Default signal pattern

When the telephone transmitter is activated by an incoming call or a triggered accessory, the following happens:

1The LED on the transmitter lights up to show that it’s signalling the receiver.

2The Visit LED on the receiver lights up and it starts to sound, ash or vibrate with a certain pace, called signal pattern.

The transmitter and the connected accessories determine the signal pattern. The default is as follows:

Transmitter Receiver signal pattern

Source LED LED Sound Vibration Flash

Landline phone Green, top Yellow light 1¯ring signal, low Medium Yes

Mobile phone sensor Green, top Yellow blinks 2¯ring signal, high Medium Yes

Other accessory Green, bottom Green light 1¯door chime, low Slow Yes

Changing the signal pattern

The transmitter controls the signal pattern. Open the transmitter front cover and move the

signal switches according to the table below to change it:

Transmitter Receiver signal pattern

Switch Source LED Sound Vibration Flash

Landline phone / test button Yellow light 1¯ring signal, low Medium Yes

Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes

Other accessory Green light 1¯door chime, low Slow Yes

Landline phone / test button Yellow light 1¯ring signal, low Medium Yes

Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes

Other accessory 2¯green blinks 2¯door chime, low Slow Yes

Landline phone / test button Yellow light 1¯ring signal, low Medium Yes

Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes

Other accessory 3¯yellow blinks 1¯ring signal, high Medium Yes

Landline phone / test button Yellow light 1¯ring signal, low Medium Yes

Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes

Other accessory 2¯orange blinks Baby melody Fast Yes

Landline phone / test button 2¯yellow blinks 2¯ring signal, low Fast Yes

Mobile phone sensor Yellow light 1¯ring signal, low Medium Yes

Other accessory 3¯orange blinks Baby melody Fast Yes

Landline phone / test button 2¯yellow blinks 2¯ring signal, low Medium Yes

Mobile phone sensor Orange blinks Baby melody Fast Yes

Other accessory Green blinks 2¯door chime, high Slow Yes

Landline phone / test button Orange blinks Baby melody Medium Yes

Mobile phone sensor 3¯yellow blinks 1¯ring signal, high Medium Yes

Other accessory 2¯green blinks 2¯door chime, low Slow Yes

Landline phone / test button 3¯yellow blinks 1¯ring signal, high Medium Yes

Mobile phone sensor 2¯yellow blinks 2¯ring signal, low Medium Yes

Other accessory Green blinks 2¯door chime, high Slow Yes

O

Changing the radio key

If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio

interference you need to change the radio key on all units. The radio key switches are located under the transmitter cover.

Here is how you change the radio key:

1Open the transmitter front cover and move any radio key switch to the up (on position) to

change the radio key. By default, all radio key switches are positioned down (o).

2Press and hold the test/function button on the receiver until the green and yellow Visit LEDs

blink alternately. Release the button.

3Press both test buttons simultaneously on the transmitter within 30 seconds to send the new radio key.

4All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. It then returns to normal mode.

Note: All Visit units must be set to the same radio key in order to operate as a group.

°5

Troubleshooting

O

If Try this

The LEDs blink in orange every minute Replace the batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries.

The transmitter LED lights up in green

but the receiver doesn’t respond

Check the the transmitter batteries and the receiver batteries and connections.

Move the receiver closer to the transmitter to make sure it’s within radio range.

Check that the units are set to the same radio key, see Changing the radio key.

The transmitter LED doesn’t light up

when the phone rings or when an

accessory is triggered

Press the test buttons on the transmitter. If the LED lights up in green, check all

connections. If the LED doesn’t light up in green, replace the batteries. Only use

1.5 V AA (LR6) lithium or alkaline batteries.

The transmitter LED doesn’t light up

when I press the test buttons

Replace the batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries. If the

LED still doesn’t light up, contact your retailer for service information.

The receiver is activated for no

apparent reason

There is probably another Visit system installed nearby that triggers your

system. Change the radio key on all units, see Changing the radio key.

1 2 4

RADIO KEY

O

Visit telephone transmitter

Andere Bellman & Symfon Sender Handbücher

Bellman & Symfon

Bellman & Symfon Visit BE1282 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon Bellman Visit BE1023 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon VISIT BE1420 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1210 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1411 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1431 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1411-CO Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1431 Montageanleitung

Bellman & Symfon

Bellman & Symfon BE1411 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon 2APAKBE1240 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1431 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1411 Montageanleitung

Bellman & Symfon

Bellman & Symfon BE1431 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon Bellman Visit BE1023 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1411 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1431 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon VISIT BE1420 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1520 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon Bellman Visit BE1123 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1411 Anwendungshandbuch

Bellman & Symfon

Bellman & Symfon BE1490 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1411 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon Bellman Visit 868 Bedienungsanleitung

Bellman & Symfon

Bellman & Symfon BE1431 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung