Bend-Pak GP-7 Bedienungsanleitung

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (800) 253-2363

Telephone: (805) 933-9970

bendpak.com

GrandPrix Two-Post Lifts

Installation and Operation Manual

Manual Revision C2 — August 2018 — Manual P/N 5900209

Models:

•GP-7

•GP-7LC

•GP-7LCS

Model GP-7 shown.

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠DANGER

Read the entire contents of this manual before using this product.

Failure to follow the instructions and safety precautions in this

manual can result in serious injury or death. Make sure all other

operators also read this manual. Keep the manual near the product

for future reference. By proceeding with setup and operation, you

agree that you fully understand the contents of this manual.

Manual. GrandPrix Series Two-Post Lifts, Installation and Operation Manual, Manual P/N 5900209, Manual

Revision C2, Released August 2018.

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain

any rights to this content, and you will not use the copies for commercial purposes.

Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. The GrandPrix logo is

a trademark of BendPak Inc. All other company, product, and service names are used for identification only. All

trademarks and registered trademarks mentioned in this manual are the property of their respective owners.

Limitations. Every effort has been made to ensure complete and accurate instructions are included in this

manual. However, product updates, revisions, and/or changes may have occurred since this manual was

published. BendPak reserves the right to change any information in this manual without incurring any obligation for

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual.

Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of

your new product. Contact your nearest BendPak dealer or visit www.bendpak.com/support/warranty for

full warranty details. Go to bendpak.com/support/register-your-product/ and fill out the online form to register

your product (be sure to click Submit).

Safety.Your new product was designed and manufactured with safety in mind. Your safety also depends on

proper training and thoughtful operation. Do not set up, operate, maintain, or repair the unit without reading and

understanding this manual and the labels on the unit.

Owner Responsibility. In order to maintain your product properly and to ensure operator safety, it is the

responsibility of the product owner to read and follow these instructions:

• Follow all installation, operation, and maintenance instructions.

• Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,

such as state and federal OSHA regulations and electrical codes.

• Read and follow all safety instructions. Keep them readily available for operators.

• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.

• Do not operate the product until you are certain that all parts are in place and operating correctly.

• Carefully inspect the product on a regular basis and perform all maintenance as required.

• Service and maintain the unit only with approved replacement parts.

• Keep the manual with the product and make sure all labels are clean and visible.

Unit Information. Enter the Model Number, Serial

Number, and the Date of Manufacture from the label

on your unit. This information is required for part or

warranty issues.

Model:

Serial:

Date of Manufacture:

GrandPrix (GP-7 Series) Two-Post Lifts 3P/N 5900209 — August 2018 — Rev. C2

Table of Contents

Introduction 3 Installation 13

Shipping Information 3 Operation 47

Safety Considerations 4 Maintenance 50

FAQ 6 Troubleshooting 52

Specifications 7 Wiring Diagram 58

Components 10 Parts Diagrams 53

Installation Checklist 12 Labels 59

Introduction

This manual describes the GrandPrix (GP-7 Series) two-post lifts from BendPak:

•GP-7. Two-post lift, 7,000 lb. capacity, 78 inch lifting height, requires a 13-foot ceiling.

•GP-7LC. Two-post lift, 7,000 lb. capacity, 68 inch lifting height, needs only a 10-foot ceiling.

•GP-7LCS. Two-post lift, 7,000 lb. capacity, 58 inch lifting height, needs only a 9-foot ceiling.

More information about the full line of BendPak products is available at bendpak.com.

This manual is mandatory reading for all users

of GP-7 Series lifts, including anyone who

installs, operates, maintains, or repairs them.

⚠DANGER Be very careful when installing, operating, maintaining, or repairing this equipment;

failure to do so could result in property damage, product damage, injury, or (in very

rare cases) death. Make sure only authorized personnel operate this equipment. All

repairs must be performed by an authorized technician. Do not make modifications

to the unit; this voids the warranty and increases the chances of injury or property

damage. Make sure to read and follow the instructions on the labels on the unit.

Keep this manual on or near the equipment so that anyone who uses or services it can read it.

If you are having issues, refer to the Troubleshooting section of this manual for assistance.

Technical support and service is available from your dealer, on the Web at bendpak.com/support,

by email at techsupport@bendpak.com, or by phone at (800) 253-2363, extension 196.

You may also contact BendPak for parts replacement information (please have the model and serial

number of your unit available) at (800) 253-2363, extension 191.

GrandPrix (GP-7 Series) Two-Post Lifts 4P/N 5900209 — August 2018 — Rev. C2

Shipping Information

Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect

the shipment

before

you sign to acknowledge that you received it.

When you sign the bill of lading, it tells the carrier that the items on the invoice were received in good

condition.

Do not sign the bill of lading until

after

you have inspected the shipment.

If any of the

items listed on the bill of lading are missing or damaged, do not accept the shipment until the carrier

makes a notation on the bill of lading that lists the missing or damaged goods.

If you discover missing or damaged goods

after

you receive the shipment and have signed the bill of

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not

make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a

specific date) and that the carrier has failed to comply with your request.

It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this

happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of

lading, freight bill, invoice, and photographs, if available. Our willingness to assist in helping you

process your claim does not make us responsible for collection of claims or replacement of lost or

damaged materials.

Safety Considerations

Read this manual carefully before using your new product.

Do not install or operate the

product until you are familiar with all operating instructions and warnings. Do not allow anyone else to

operate the product until they are also familiar with all operating instructions and warnings.

Safety Information

Please note the following:

•GP-7 Series lifts are two-post lifts.

Use them only for their intended purpose.

If you are

looking for a

parking

lift, visit the Bendpak website.

•Only operate your lift between temperatures of 41°F to 104°F (5°C to 40°C).

•The product should only be operated by authorized personnel. Keep children and untrained

personnel away from the product.

•Do not use the product while tired or under the influence of drugs, alcohol, or medication.

•Do not make any modifications to the product; this voids the warranty and increases the chances

of injury or property damage.

•Make sure all operators read and understand the Installation and Operation Manual. Keep the

manual near the device at all times.

•Make a visual inspection of the product before using it. Do not use the product if you find any

missing or damaged parts. Instead, contact an authorized repair facility, your distributor, or

BendPak at (805) 933-9970 or techsupport@bendpak.com.

•BendPak recommends making a

thorough

inspection of the product at least once a year.

Replace any damaged or severely worn parts, decals, or warning labels.

GrandPrix (GP-7 Series) Two-Post Lifts 5P/N 5900209 — August 2018 — Rev. C2

Symbols

Following are the symbols used in this manual:

⚠DANGER Calls attention to a hazard that will result in death or injury.

⚠WARNING Calls attention to a hazard or unsafe practice that could result in death or injury.

⚠CAUTION Calls attention to a hazard or unsafe practice that could result in personal injury,

product damage, or property damage.

Tip Calls attention to information that can help you use your unit better.

Liability Information

BendPak assumes no liability for damages resulting from:

• Use of the equipment for purposes other than those described in this manual.

• Modifications to the equipment without prior, written permission from BendPak Inc.

• Damage to the equipment from external influences.

• Incorrect operation of the equipment.

Electrical Information

⚠DANGER All wiring

must

be performed by a licensed, certified electrician. Do not perform

any maintenance until main electrical power has been disconnected from the lift

and cannot be re-energized until all procedures are complete.

Important electrical information:

•Improper electrical installation can damage the Power Unit motor;

this damage is not covered by

the warranty

•Use a separate circuit breaker for each Power Unit.

•Protect each circuit with a time delay fuse or circuit breaker:

–For a 208 to 230 VAC,

single phase

circuit, use a 25 amp fuse.

–For a 208 to 230 VAC,

three phase

circuit, use a 20 amp fuse.

–For a 380 to 440 VAC,

three phase

circuit, use a 15 amp fuse.

Concrete Information

The concrete floor where you want to install your lift must meet the following requirements:

•The floor must be a flat, concrete floor; it must be level; do not install the lift on a the surface with

more than three degrees of slope.

•Do not install the lift on cracked or defective concrete.

•Make sure the concrete is at least 4.25 inches thick, 3,000 PSI, and cured for 28 days minimum.

•Check the floor for the possibility of it being a post tension slab. In this case, contact the building

architect before drilling. Using ground penetrating radar may help you find the tensioned steel.

GrandPrix (GP-7 Series) Two-Post Lifts 6P/N 5900209 — August 2018 — Rev. C2

Frequently Asked Questions

Question: What kinds of vehicles can I lift on my GP-7 Series lift?

Answer: Cars, light trucks, and SUVs; up to 7,000 lbs (3,175 kg) each.

Q: How long will it take to raise or lower my vehicle?

A: About 45 seconds, depending on what locking position you use.

Q: Does the lift have to be anchored in place?

A: Yes. Two-post lift posts must be anchored. Your lift comes with high-quality, Automotive Lift

Institute-certified Anchor Bolts; use only the Anchor Bolts that came with your lift.

Q: How thick does my concrete have to be?

A: Concrete specifications are: 4.25 inches thick, 3,000 PSI, cured for a minimum of 28 days. Do not

install the lift on cracked or defective concrete. Do not install the lift on asphalt or any surface other

than concrete.

Q: Can I install my lift outside?

A: No. GP-7 Series lifts are approved for indoor installation and use only. Outdoor installation is

prohibited.

Q: Which end is the front of the lift?

A: To determine the front of your lift, drive a vehicle in straight and stop. The front of the vehicle is

where the front of the lift is.

Q: Does it matter if I drive my vehicles in front first or back them in?

A: No. Most people drive their vehicles in front first, which makes it easier to open the vehicle doors.

Other than that, you can drive your vehicles in whichever way you want; the lift works great either way.

Q: How long can I leave a vehicle up?

A: Basically as long as you want, as long as the lift is on a Safety Lock. The locking system is based

on gravity and smart engineering. Once a Safety Lock is engaged, gravity holds the lift in position, so a

loss of power has no effect; your vehicle is going to stay exactly where you left it. Always leave your lift

either on the ground or on a Safety Lock.

Q: How many Safety Lock positions does my lift have?

A: Eleven, spaced every 4 inches.

GrandPrix (GP-7 Series) Two-Post Lifts 7P/N 5900209 — August 2018 — Rev. C2

Specifications

GrandPrix (GP-7 Series) Two-Post Lifts 8P/N 5900209 — August 2018 — Rev. C2

GrandPrix (GP-7 Series) Two-Post Lifts 9P/N 5900209 — August 2018 — Rev. C2

Model GP-7LCS GP-7LC GP-7

Lifting capacity 7,000 lbs / 3,175 kg

E– Height overall 106.5" / 2,703 mm 118.5" / 3,008 mm 150" / 3,814 mm

F– Width overall 124.7" / 3,168 mm

G- Outside posts 119.5" / 3,034 mm

J- Floor to Trip Stop Tube 97.5" / 2,479 mm 109.5" / 2,784 141.25" / 3,590 mm

H– Inside posts 110.1" / 2,798 mm

K- Reach (front arm min) 27" / 688 mm

K- Reach (front arm max) 44.6" / 1,133 mm

L- Reach (rear arm min) 28" / 711 mm

L- Reach (rear arm max) 47" / 1,194 mm

D- Minimum pad height 4.5" / 113 mm

A– Rise 53.25" / 1,350 mm 63.25" / 1,604 mm 73.5" / 1,864.5 mm

B– Rise + pad 57.5" / 1,463 mm 67.5" / 1,717 mm 77.75" / 1,977.5 mm

C– Rise + pad + adapter 65.75" / 1,673 mm 75.75" / 1,927 mm 86.25" / 2,190.6 mm

I- Drive-thru width 89.5" / 2,273 mm

Top Trough width 119.4" / 3,034 mm

Motor 220 VAC, 60 Hz, 1Ph

Time to full rise ~45 seconds

Maximum operating

hydraulic pressure

2,940 PSI

Sound 70 dB

GrandPrix (GP-7 Series) Two-Post Lifts 10 P/N 5900209 — August 2018 — Rev. C2

Components

GP-7 Series lift components include:

•Powerside Post: The Powerside Post holds the Power Unit, the Safety Lock Release Handle,

the Lowering Handle, and the Power Disconnect Switch. You can use either post as the Powerside

Post and the Powerside Post can be on either side of the lift.

•Offside Post: The other post. Identical to the Powerside Post, but when you select a Powerside

Post, the other post automatically becomes the Offside Post.

•Power Unit: Provides hydraulic power to the lift. Connects to a 220 VAC power source. Includes

the button that raises the lift and an Hydraulic Fluid reservoir that must be filled before use.

•Safety Locks: Hold the Lift Arms while they are raised. Multiple Safety Locks let you select the

best Lift Arm height for your needs. Safety Locks use gravity and intelligent engineering to hold the

Lift Arms up once they are on a Safety Lock; even if the lift loses power, the Lift Arms will stay right

where they are if they were left on a Safety Lock. Only leave your GP-7 Series lift on the

ground or on a Safety Lock.

•Safety Lock Release Handle: Releases the lift from its current Safety Lock. To lower a vehicle

from a raised position, hold down the Safety Lock Release Handle and then press down the

Lowering Handle.

•Lowering Handle: Lowers a vehicle from a raised position when used with the Safety Lock

Release Handle.

•Lift Pads: Rubber pads that contact the lifting points of the vehicles you lift. Also included with

your lift are three sets of extensions (short, medium, and tall) that can be used with the Lift Pads.

•Lift Arms: Extendable steel arms that attach to the Lift Heads. Lift Arms hold the Lift Pads; after a

vehicle is moved into place, the Lift Arms are moved so that the rubber pads contact the lifting

points on the vehicle. The Lift Arms are one of the components that actually holds a vehicle up.

•Lift Heads: Sometimes called carriages. Lift Heads move up and down in the posts. They

connect to the Lift Arms, so when the Lift Heads move up, the Lift Arms also move up, thus raising

the vehicle.

•Top Trough: The beam across the top of the lift; it supports the lift’s structure and holds the

Hydraulic Cylinder and the Lifting Cables.

•Trip Stop Tube: Located on the underside of the Top Trough, the Trip Stop Tube stops upward

movement of the lift. If you are raising a vehicle and it hits the Trip Stop Tube, the lift immediately

stops moving up.

•Power Disconnect Switch: Immediately interrupts main electrical power to the lift. Used for

electrical circuit faults, emergency situations, or when lift is undergoing service or maintenance.

Andere Handbücher für GP-7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bend-Pak Hebesystem Handbücher

Bend-Pak

Bend-Pak MDS-6EXT Bedienungsanleitung

Bend-Pak

Bend-Pak P-9000LT Bedienungsanleitung

Bend-Pak

Bend-Pak XP Series Bedienungsanleitung

Bend-Pak

Bend-Pak Clearfloor 10AP-168 Bedienungsanleitung

Bend-Pak

Bend-Pak EXCEL Series Bedienungsanleitung

Bend-Pak

Bend-Pak GP-7LCS Bedienungsanleitung

Bend-Pak

Bend-Pak HD-14SS Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9XW Bedienungsanleitung

Bend-Pak

Bend-Pak PL-6KDT Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10A Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-181 Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-14X Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10S Bedienungsanleitung

Bend-Pak

Bend-Pak HD-12LS Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10T Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10-168 Bedienungsanleitung

Bend-Pak

Bend-Pak HDSO-14AX Bedienungsanleitung

Bend-Pak

Bend-Pak XP-10CX Bedienungsanleitung

Bend-Pak

Bend-Pak GP-7 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-7P Bedienungsanleitung

Bend-Pak

Bend-Pak P-9000LTF Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-27 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10 Series Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9XL Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung