Bend-Pak HDSO-14AX Bedienungsanleitung

INSTALLATION AND OPERATION MANUAL

FOUR-POST OPEN FRONT ALIGNMENT LIFTS

COMMERCIAL GRADE

14,000 LBS. CAPACITY

Models:

• HDSO-14P Version A

• HDSO-14AX Version A

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO

INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION

AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND AND

COMPREHEND THE FULL CONTENTS OF THIS MANUAL. FORWARD THIS

MANUAL TO ALL OPERATORS. FAILURE TO OPERATE THIS EQUIPMENT AS

DIRECTED MAY CAUSE INJURY OR DEATH.

Revision A6 – December 2018

Part Number 5900001

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

Fax: 1-805-933-9160

www.bendpak.com

Keep this operation manual near the

machine at all times. Make sure that

ALL USERS read this manual.

RECEIVING

The shipment should be thoroughly inspected as soon as it is

received. The signed Bill of Lading is acknowledgement by

the shipping carrier as receipt of this product as listed in your

invoice as being in a good condition of shipment. If any of

these goods listed on this Bill of Lading are missing or dam-

aged, do not accept goods until the shipping carrier makes a

notation on the freight bill of the missing or damaged goods.

Do this for your own protection.

BE SAFE

Your new lift was designed and built with safety in mind.

However, your overall safety can be increased with proper

training and thoughtful operation on the part of the operator.

DO NOT operate or repair this equipment without reading this

manual and the important safety instructions shown inside.

Keep this operation manual near the lift at all times. Make sure

that ALL USERS read and understand this manual.

400V 50Hz SUPPLY DETAILS ARE

INCLUDED WITH ELECTRICAL

CONTROL BOX. DISREGARD SUPPLY

WIRING DETAILS IN THIS MANUAL

EUROPEAN USERS

ORIGINAL INSTRUCTIONS IN

ENGLISH LANGUAGE

14,000 POUND CAPACITY, COMMERCIAL GRADE

FOUR POST OPEN FRONT ALIGNMENT AUTO / TRUCK LIFT

This instruction manual has been prepared especially for you.

Your new lift is the product of over 40 years of continuous research, testing and development;

it is the most technically advanced lift on the market today.

READ THIS ENTIRE MANUAL BEFORE

INSTALLATION & OPERATION BEGINS.

RECORD HERE THE LIFT AND

POWER UNIT INFORMATION WHICH IS LOCATED

ON THE SERIAL NUMBER DATA PLATES ON THE LIFT

AND ON THE POWER UNIT

Power Unit Model # _____________

Power Unit Date Of Mfg. _____________

Power Unit Serial # _____________

Maximum Operating

Hydraulic Pressure 2,950 PSI

This information is required when

calling for parts or warranty issues.

PRODUCT WARRANTY

Our comprehensive product warranty means more than a commitment to you; it’s also a commitment to the value of your

new BendPak lift. For full warranty details and to register your new lift contact your nearest BendPak dealer or visit:

http:/ /www.bendpak.com/support/warranty/

NOTE:

Every effort has been taken to ensure complete and accurate instructions have been included in this manual, however, possible product

updates, revisions and or changes may have occurred since this printing. BendPak Ranger reserves the right to change speciﬁcations

without incurring any obligation for equipment previously or subsequently sold. Not responsible for typographical errors.

IMPORTANT NOTICE

Do not attempt to install this lift if you have never been

trained on basic automotive lift installation procedures.

Never attempt to lift components without proper lifting

tools such as forklift or cranes. Stay clear of any

moving parts that can fall and cause injury. These

instructions must be followed to ensure proper installa-

tion and operation of your lift. Failure to comply with these

instructions can result in serious bodily harm and void

product warranty. Manufacturer will assume no liability for

loss or damage of any kind, expressed or implied resulting

from improper installation or use of this product.

PLEASE READ ENTIRE MANUAL

PRIOR TO INSTALLATION.

DEFINITIONS OF

HAZARD LEVELS

Identify the hazard levels used in this manual with the

following definitions and signal words:

Watch for this symbol: It means immediate hazards which

will result in severe personal injury or death.

Watch for this symbol: It means hazards or unsafe

practices which could result in severe personal

injury or death.

Watch for this symbol: It means hazards or unsafe

practices which may result in minor personal injury, prod-

uct or property damage.

OWNER’S RESPONSIBILITY

To maintain the lift and user safety, the responsibility of the

owner is to read and follow these instructions:

tFollow all installation and operation instructions.

tMake sure installation conforms to all applicable Local,

State, and Federal Codes, Rules, and Regulations;

such as State and Federal OSHA Regulations and

Electrical Codes.

tCarefully check the lift for correct initial function.

tRead and follow the safety instructions. Keep them

readily available for machine operators.

tMake certain all operators are properly trained, know

how to safely and correctly operate the unit, and are

properly supervised.

tAllow unit operation only with all parts in place and

operating safely.

tCarefully inspect the unit on a regular basis and

perform all maintenance as required.

tService and maintain the unit only with authorized or

approved replacement parts.

tKeep all instructions permanently with the unit and

all decals on the unit clean and visible.

BEFORE YOU BEGIN

Receiving:

The shipment should be thoroughly inspected as soon as it is

received. The signed bill of lading is acknowledgement by the

carrier of receipt in good condition of shipment covered by

your invoice. If any of the goods called for on this bill of lading

are shorted or damaged, do not accept them until the carrier

makes a notation on the freight bill of the shorted or damaged

goods. Do this for your own protection.

NOTIFY THE CARRIER AT ONCE if any hidden loss or

damage is discovered after receipt and request the carrier

to make an inspection. If the carrier will not do so, prepare

a signed statement to the effect that you have notified the

carrier (on a specific date) and that the carrier has failed to

comply with your request.

IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE

AFTER YOU HAVE GIVEN THE CARRIER A CLEAR

RECEIPT. File your claim with the carrier promptly. Support

your claim with copies of the bill of lading, freight bill, invoice,

and photographs, if available. Our willingness to assist in

helping you process your claim does not make BendPak

responsible for collection of claims or replacement of lost or

damaged materials.

TABLE OF CONTENTS

Warranty / Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Definitions of Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Owner’s Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installers / Operators Agreement / Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Safety / Warning Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Step 1 / Selecting Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Step 2 / Floor Requirements / Concrete Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Assembly View / Description of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Floor Plan / Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Power Unit Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Step 3 / Column and Cross Tube Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13

Step 4 / Anchoring The Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14

Step 5 / Raising the Cross Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Step 6 / Powerside Runway Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Step 7 / Offside Runway Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Step 8 / Cable Sheave Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Step 9 / Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-18

Step 10 / Power Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Step 11 / Routing Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-21

Step 12 / Routing Air Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22

Step 13 / Power Unit Hook Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-25

Step 14 / Inspecting Slack Safety Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Step 15 / Lift Start Up / Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26

Step 16 / Attaching Approach Ramps / Tire stops.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

Step 17 / Leveling/Synchronizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Step 18 / Adding Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Step 19 / Bleeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Optional Equipment Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29-30

Step 19 / Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Step 20 / Lift Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-33

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34 & 43

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-42

Maintenance Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Installation Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Part Number Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-55

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

INSTALLER / OPERATOR

PLEASE READ AND FULLY

UNDERSTAND.

BY PROCEEDING YOU AGREE TO

THE FOLLOWING.

tI have visually inspected the site where the lift is to be

installed and verified the concrete to be in good condi-

tion and free of cracks or other defects. I understand that

installing a lift on cracked or defective concrete could

cause lift failure resulting in personal injury or death.

tI understand that a level floor is required for proper

installation and level lifting.

tI understand that I am responsible if my floor is of

questionable slope and that I will be responsible for all

charges related to pouring a new level concrete slab if

required and any charges.

tI understand that BendPak lifts are supplied with

concrete fasteners meeting the criteria of the

American National Standard “Automotive Lifts -

Safety Requirements for Construction, Testing, and

Validation” ANSI/ALI ALCTV-2011, and that I will

be responsible for all charges related to any special

regional structural and/or seismic anch oring require-

ments specified by any other agencies and/or codes

such as the Uniform Building Code (UBC) and/or

International Building Code (IBC).

tI assume full responsibility for the concrete floor and

condition thereof, now or later, where the above

equipment model(s) are to be installed. Failure to fol-

low danger, warning, and caution instructions may

lead to serious personal injury or death to operator or

bystander or damage to property.

tI understand that Bendpak lifts are designed to be

installed in indoor locations only. Failure to follow

installation instructions may lead to serious personal

injury or death to operator or bystander or damage to

property or lift.

Failure to follow danger, warning, and caution instructions

may lead to serious personal injury or death to operator or

bystander or damage to property.

Please read entire manual prior to installation.

Do not operate this machine until you read and understand

all the dangers, warnings and cautions in this manual.

For additional copies or further information, contact:

BendPak Inc. / Ranger Products

1645 Lemonwood Dr.

Santa Paula, CA. 93060

1-805-933-9970

www.bendpak.com

INSTALLER / OPERATOR

PROTECTIVE EQUIPMENT

Personal protective equipment helps makes installation

and operation safer, however, it does not take the place

of safe operating practices. Always wear durable work

clothing during any installation and/or service activity. Shop

aprons or shop coats may also be worn, however loose

fitting clothing should be avoided. Tight fitting leather

gloves are recommended to protect technician hands

when handling parts. Sturdy leather work shoes with steel

toes and oil resistant soles should be used by all service

personnel to help prevent injury during typical

installation and operation activities.

Eye protection is essential during installation

and operation activities. Safety glasses with

side shields, goggles, or face shields are

acceptable. Back belts provide support dur-

ing lifting activities and are also helpful in

providing worker protection. Consideration

should also be given to the use of hearing protection if

service activity is performed in an enclosed area, or if noise

levels are high.

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED

COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OR YOURSELF AND OTHERS

AND CAN CAUSE PERSONAL INJURY OR DEATH. READ AND FOLLOW ALL INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

1. Carefully remove the crating and packing

materials. CAUTION! Be careful when cutting steel

banding material as items may become loose and fall caus-

ing personal harm or injury.

2. Check the voltage, phase and proper amperage

requirements for the motor shown on the motor plate.

Wiring should be performed by a certified electrician only.

IMPORTANT SAFETY INSTRUCTIONS

Read these safety instructions entirely!

IMPORTANT NOTICE

Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures.

Never attempt to lift components without proper lifting tools such as forklift or cranes.

Stay clear of any moving parts that can fall and cause injury.

INTRODUCTION

1. READ AND UNDERSTAND all safety warning proce-

dures before operating lift.

2. KEEP HANDS AND FEET CLEAR. Remove hands and

feet from any moving parts. Keep feet clear of lift when lowering.

Avoid pinch points.

3. KEEP WORK AREA CLEAN. Cluttered work areas invite

injuries.

4. Consider work area environment. Do not expose equip-

ment to rain. DO NOT use in damp or wet locations. Keep area

well lighted.

5. ONLY TRAINED OPERATORS should operate this lift.

All non-trained personnel should be kept away from work area.

Never let non-trained personnel come in contact with, or oper-

ate lift.

6. USE LIFT CORRECTLY. Use lift in the proper manner.

Never use lifting adapters other than what is approved by the

manufacturer.

7. DO NOT override self-closing lift controls.

8. REMAIN CLEAR of lift when raising or lowering vehicle.

9. CLEAR AREA if vehicle is in danger of falling.

10. ALWAYS ENSURE that the safeties are engaged before

any attempt is made to work on or near vehicle.

11. DRESS PROPERLY. Non-skid steel-toe footwear is

recommended when operating lift.

12. GUARD AGAINST ELECTRIC

SHOCK. This lift must be grounded while

in use to protect the operator from electric

shock. Never connect the green power cord

wire to a live terminal. This is for ground only.

13. DANGER! The power unit used on this lift contains high

voltage. Disconnect power at the recep-

tacle before performing any electrical repairs.

Secure plug so that it cannot be accidentally

plugged in during service.

14. WARNING! RISK OF EXPLOSION. This equipment has

internal arcing or sparking parts which should not

be exposed to flammable vapors. This machine

should not be located in a recessed area or

below floor level.

15. MAINTAIN WITH CARE. Keep lift clean for better and

safer performance. Follow manual for proper lubrication and

maintenance instructions. Keep control handles and/or buttons

dry, clean and free from grease and oil.

16. STAY ALERT. Watch what you are doing. Use common

sense. Be aware.

17. CHECK FOR DAMAGED PARTS. Check for alignment

of moving parts, breakage of parts or any condition that may

affect its operation. Do not use lift if any component is broken

or damaged.

18. NEVER remove safety related components from the lift.

Do not use lift if safety related components are damaged or

missing.

19. Keep hair, loose clothing, fingers, and all parts of body

away from moving parts

20. Use only as described in this manual. Use only manu-

facturer’s recommended attachments

21. ALWAYS WEAR SAFETY GLASSES. Everyday

eyeglasses only have impact resistant lenses, they are not

safety glasses

22. SAVE THESE INSTRUCTIONS.

STEP 1

(Selecting Site)

Before installing your new lift, check the following.

1. LIFT LOCATION: Always use architects plans when

available. Check layout dimension against floor plan

requirements making sure that adequate space is available.

2. OVERHEAD OBSTRUCTIONS: The area where the lift

will be located should be free of overhead obstructions such

as heaters, building supports, electrical lines etc.

3. DEFECTIVE FLOOR: Visually inspect the site where

the lift is to be installed and check for cracked or defective

concrete.

4. Lift is designed for INDOOR INSTALLATION ONLY.

Outdoor use is prohibited. Always follow warnings illustrated

on equipment labels.

STEP 2

(Floor Requirements)

This lift must be installed on a solid level concrete floor.

A level floor is suggested for proper use and installation

and level lifting. If a floor is of questionable slope, consider

a survey of the site and/or the possibility of pouring a new

level concrete slab.

tDO NOT install or use this lift on any asphalt surface

or any surface other than concrete.

tDO NOT install or use this lift on expansion seams

or on cracked or defective concrete.

tDO NOT install or use this lift on a second / elevated

floor without first consulting a building architect.

tRefer to ANSI/ALI ALIS Standard (R2015) Safety

Requirements for Installation and Service for more informa-

tion about safely installing your Lift.

CONCRETE SPECIFICATIONS

LIFT MODEL CONCRETE REQUIREMENTS

HDSO-14P 4” Min. Thickness / 3,000 PSI

HDSO-14AX 4” Min. Thickness / 3,000 PSI

All models MUST be installed on 3000 PSI concrete only

conforming to the minimum requirements shown above.

New concrete must be adequately cured by at least

28 days minimum.

IMPORTANT NOTICE

These instructions must be followed to ensure proper installation and operation of your lift.

Failure to comply with these instructions can result in serious bodily harm and void product warranty.

Manufacturer will assume no liability for loss or damage of any kind, expressed or implied resulting from

improper installation or use of this product.

PLEASE READ ENTIRE MANUAL PRIOR TO INSTALLATION

tRotary Hammer Drill or Similar

t3/4” Masonry Bit

tHammer

t4 Foot Level

tOpen-End Wrench Set: SAE/Metric

tSocket And Ratchet Set: SAE/Metric

tHex-Key / Allen Wrench Set

tLarge Crescent Wrench

tLarge Pipe Wrench

tCrow Bar

tChalk Line

tMedium Flat Screwdriver

tTape Measure: 25 Foot Minimum

tNeedle Nose Pliers

TOOLS REQUIRED

NOTE:

An air supply (30 PSI Min / 3 CFM Min) will be required for the safety-lock mechanisms. See page 19, Step 11.

IMPORTANT NOTE:

BendPak lifts are supplied with installation instructions and concrete fasteners meeting the criteria as prescribed

by the American National Standard "Automotive Lifts - Safety Requirements for Construction, Testing, and

Validation" ANSI/ALI ALCTV-2011. Lift buyers are responsible for any special regional structural and/or seismic

anchoring requirements specied by any other agencies and/or codes such as the

Uniform Building Code (UBC) and/or International Building Code (IBC).

IMPORTANT NOTE:

The power unit must be installed as shown above. It is important to locate the

POWER-SIDE runway (with cylinder) on the SAME SIDE as the power unit.

Rolling Jack / Utility rails on the side of each runway MUST be installed to the inside.

When removing the lift from shipping angles pay close attention as the

runways can slide and can cause injury. Prior to removing the bolts make sure the runways are

held securely by a fork lift or some other heavy lifting device.

Small Window

Large Window

Cross Tube

Small Window

Carriage

Power Side

Runway

Power Unit

Mounting Plate

Off Side

Runway

FLOOR PLAN

* IMPORTANT NOTE *

Check diagonal measurements to confirm square layout; diagonal measurements must be equal.

Model HDSO-14P HDSO-14AX

Lifting Capacity 14,000 lbs / 6350 kg 14,000 lbs / 6350 kg

A - Overall Width / Front 143” / 3638 mm 143” / 3638 mm

A - Overall Width / Rear 130” / 3304 mm 130” / 3304 mm

B - Outside Length 215 ½” / 5472 mm 215 ½” / 5472 mm

C - Overall Length 244” / 6195 mm 244” / 6191 mm

D - Height of Columns / Front 103” / 2623 mm 103” / 2623 mm

D - Height of Columns / Rear 92” / 2338 mm 92” / 2338 mm

E - Min. Runway Height 7-5/8" / 192 mm 7-5/8" / 192 mm

F - Max. Rise 70” / 1778 mm 70” / 1778 mm

G - Max Lifting Height 77 ½” / 1970 mm 77 ½” / 1970 mm

H - Width Between Columns / Front 113” / 2800 mm 113” / 2800 mm

H - Width Between Columns / Rear 110” / 2796 mm 110” / 2796 mm

I - Runway Width 20” / 508 mm 20” / 520 mm

J - Width Between Runways(*) 45” / 1146 mm 45” / 1146 mm

K - Length of Runways 199” / 5054 mm 199” / 5054 mm

L - Min. 4- Wheel Alignment (**) 72” / 1828 mm 89” / 2261 mm

M - Max 4 Wheel Alignment (**) 135” / 3428 mm 156” / 3962 mm

N - Max 2 Wheel Alignment (**) 174” / 4420 mm 182” / 4623 mm

Min. Wheelbase @ Rated Capacity 140” / 3556 mm 140” / 3556 mm

Min. Wheelbase 75% Rated Capacity 120” / 3048 mm 120” / 3048 mm

Min. Wheelbase 50% Rated Capacity 100” / 2540 mm 100” / 2540 mm

Min. Wheelbase 75% Rated Capacity 80” / 2032 mm 80” / 2032 mm

Locking Positions 13 13

Lock Spacing Every 4” / 102 mm Every 4” / 102 mm

Lifting Time 60 Seconds 60 Seconds

Standard Motor 220 VAC / 60Hz 1 Ph. 220 VAC / 60Hz 1 Ph.

Emission sound pressure at Operator Position < 70 dB(A)

* This dimension may be limited with the addition of rolling jacks. See Rolling Jack Speciﬁcations on Separate

page.

** For CE compliant countries see errata sheet included with control panel.

The design, material and speciﬁcations are subject to change without notice.

CLEARANCES

1. Lift Location: Use architects plan and Engineers

automatic level (transit) when available to locate lift. The

above shows clearances of a typical bay layout. Lift ﬂoor

area should be level.

2. Ceiling or overhead clearance must be 80” plus height of

tallest vehicle.

3. Estimating Column Shim requirements:

In the following section, the terms “highest” and “low-

est” refer to elevation of ﬂoor.

a. Mark locations where lift columns will be posi-

tioned in bay.

b. Place target on ﬂoor at column positions (NOT on

column base plates) and record readings.

c. Find the highest of the four locations. Find the

difference between the readings at each of the

remaining three columns and the highest reading.

d. The difference is the estimated amount of shim

thickness needed at each column.

Note: Maximum shim thickness is 1/2” per column using

shims and anchors provided with lift.

If no transit is available, ﬂoor slope can be determined by

using a chalk line and level.

Andere Handbücher für HDSO-14AX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bend-Pak Hebesystem Handbücher

Bend-Pak

Bend-Pak xpR-10C-168 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-12SS-B Bedienungsanleitung

Bend-Pak

Bend-Pak HD-75BXT Bedienungsanleitung

Bend-Pak

Bend-Pak EV2400SL Bedienungsanleitung

Bend-Pak

Bend-Pak PL-6KDT Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9FS Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-181 Bedienungsanleitung

Bend-Pak

Bend-Pak P-9000LTF Bedienungsanleitung

Bend-Pak

Bend-Pak HDSO-14P Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10T Bedienungsanleitung

Bend-Pak

Bend-Pak XP-10CX Bedienungsanleitung

Bend-Pak

Bend-Pak LR-60P Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9 Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-27 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-LP Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AXLS-LP Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9SWX Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-18CL-192 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-7W Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9 Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-14 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-14SS Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9D Series Bedienungsanleitung

Bend-Pak

Bend-Pak GP-9XLT Package Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung