Berger & Schroter SG880MK-8mHD Bedienungsanleitung

User’s Manual

Infrared Mobile Digital S outing Camera

SG880MK-8mHD

Item No. 31484

Inhaltsverzei hnis

1 Instru tion 23

1.1 General Des ription 23

1.2 Camera Body Interfa es 23

1.3 Remote Control 24

1.3.1 Navigating 25

1.3.2 Chara ters 25

1.4 Shooting Information Display 25-26

1.5 MMS/GPRS fun tion 26

2 Cautions 27

3 Qui k Start Guide 27

3.1 Power Supply 27

3.2 Insert the SD ard and the SIM ard 28

3.3 Do the Camera Settings 28

3.4 Enter into the TEST Mode 28

3.4.1 Custom Settings 29

3.4.2 Manual Capturing 29

3.4.3 Send MMS 29

3.5 Power on and Enter into the ON Mode 29

3.6 SMS Control 29

3.7 SMS Command List 30

3.8 Power Off 31

4 Advan ed Operations 31

4.1 Settings Menu 31-35

4.2 Default Setting 36

4.3 Playba k 37

4.3.1 View Photo 37

4.3.2 Delete Photo or Video 37

4.4 Laser Pointer 37

4.5 File Numbering 37

Appendix I: PIR Dete tion Zone 38-39

Appendix II: Te hni al Spe ifi ations 40

Appendix III: Parts List 40

1 Instru tion

1.1 General Des ription

This camera, a digital scouting camera with black IR and MMS function,

is a digital infrared surveillance camera, triggered by any movement of

humans or animals monitored by a high sensitive Passive Infrared (PIR)

motion sensor, and then automatically captures high quality pictures (up

to 8M pixels) or records video clips (720P HD) according to default set-

tings or preset customer settings. It will then send the pictures instantly

to your mobile device or e-mail via GSM/GPRS network. You’ll be alerted

just when the camera is triggered or per custom settings.

It takes color pictures or videos under sufficient daylight. While at night,

the built-in 940nm IR LEDs take clear pictures or videos (monochrome).

It’s invisible to game. And this model has a new design of PIR and this

new PIR is patented.

There is a 1.5” color LCD display screen on the camera and a sound

recorder embedded in the camera. A laser pointer is used to help target

the photo area of the camera. It supports MMS/SMS/E-mail via

GSM/GPRS Network.

It is resistant against water and snow. The camera can also be used as

a portable digital camera.

1.2 Camera Body Interfa es

The camera has the following I/O interfaces: US connector, SD card

Slot, TV output and external DC power connector.

Take a few moments to familiarize yourself with the camera controls and

displays. It is helpful to bookmark this section and refer to it when rea-

ding through the rest of the manual.

1. ottom cover

2. TV-out connector

3. Power switch

4. SD-Card slot

5. Laser pointer

6. Lens

7. PIR

8. Antenna

9. LCD Display

10. Sound

recorder

11. Indication

LED

12. IR flash

13. SIM Card

slot

14. US

connector

15. Lock

16. attery depot

17. attery

depot handle

1.3 Remote Control

The remote control is the input device for the ca-

mera and is primarily used for customer settings

and password input. This is an infrared type wi-

reless remote control. The maximum remote di-

stance is 30 feet.

Fig. 1 Diagram of camera functional indicators

Fig. 2 Remote control

Note:

The remote will not work properly without the

antenna attached.

When power on the camera, allow approxi-

mately 10-20 seconds for the camera to ac-

quire a signal. The remote will not function

properly until the camera has acquired a si-

gnal. You can determine that the camera has

acquired a signal by locating the signal icon

on the LCD screen.

Select item (UP)

Increase value

Make

selection (OK)

Select option

(right)

Select item (down)

Decrase value

Display menus /Exit

(MENU)

Select option (LEFT)

1.3.2 Chara ters

When entering digits, letters or

punctuations into an input column,

there are some useful characters

that can be used by pressing the

button continuously:

: 1 . / : @ _ : 0 + -

Press the pun tuation “*” for

laser pointer.

Abb. 3 Place the remote

control in the camera

1.3.1 Navigating

Press UP or DOWN to select or highlight the menu item. Press LEFT or

RIGHT to select the option of each item and press OK to make a selec-

tion.

3. Image size

1.4 Shooting Information Display

When the camera is turned on (the power switch is slid to ON or TEST

position), the current settings will be displayed on screen.

2. Camera

mode

1. SIM card

4. Signal strength

5. atterylevel

6. Tlecom provide

7. Date (M;D;Y)

8. Time /H;M;S)

9. Available space

10. Number of images

1.5 MMS/GPRS fun tion

This camera can send pictures instantly to your mobile device via

GSM/GPRS network. You’ll be alerted just when a picture or video has

been taken. The camera sends MMS message through GPRS network,

so before using this function, you need to open GPRS service from your

service provider. It supports four bands ：850MHz, 900MHz, 1800MHz

and 1900MHz.

SIM card Icon：There are two SIM card icons which stand for different

installation situations. means the SIM card is inserted and it works

well. means the MMS function can’t work correctly because of loss

of signal or other communication issues.

There are 4 submenu settings within the MMS/GPRS function. They are

Send Mode, MMS Set, GPRS Set and Send to. Send Mode means to

choose a way to send MMS (refer to 4.1 table). MMS Set and GPRS

Set means to have the right MMS and GPRS setting parameters accor-

ding to your network. Send to means to input the phone number or

email address which you want to send to. All 4 submenus must be cor-

rectly set up.

Fig.4 Shooting

information display

2 Cautions

• Please install batteries according to shown polarity.

• Please unlock the write-protect before inserting the SD card.

• Please insert the SD card when the power switch is in the OFF

position before testing the camera. The camera has no internal

memory for saving images or videos. If no SD card is inserted, the

camera will shut down automatically after a continuous indication

sound.

• Please do not insert or take out the SD card when the power switch

is in the ON position.

• It is recommended to format the SD card by the camera when used

for the first time.

• The camera will be in US mode when connected to a US port of

a computer. In this case, the SD card function is as a removable disk.

• In the TEST mode, the camera will shut down automatically after 3

minutes if no operation is done. Please turn on the power again if you

want to continue to work with the remote.

• Please ensure there is sufficient power when having a firmware

upgrade, otherwise the upgrade process could be interrupted and

the camera may stop functioning properly

3 Qui k Start Guide

3.1 Power Supply

To supply power for the camera, four or eight size AA batteries are nee-

ded. The following batteries with 1.5V output can be used:

1. High-density and high-performance alkaline batteries

(Recommended)

2. Rechargeable alkaline batteries

3. Rechargeable NiMH batteries

There are four battery slots. Slot 1 and 2 form one group and is marked

“1”while slot 3 and 4 form the other group and is marked “2”. Only one

“group” of batteries is needed to supply power to the camera, but both

can be used and is recommended.

When in a low-battery state, the camera will be automatically shut down

after two indication sounds. Please change the batteries at this time. If

you have set the MMS function, it will send you a MMS/SMS or Email

to indicate the low battery situation.

Fig.5 attery install

Dear Customer! Please note! Depending

on battery regulations you are required to

used or defective batteries and accumula-

tors, at no cost to you, return it to us

Every consumer is legally obliged to dis-

pose of WEEE separately from the house-

hold waste and to dispose of at a collection

site of his community / City District for ex-

ample. Electric appliances are marked with

the crossed out dustbin, accepted there for

free.

Caution: Risk of explosion if battery is repla ed by an in orre t

type. Also dispose of used batteries a ording to the instru tions.

3.2 Insert the SD ard and the SIM ard

Open the bottom cover. Insert SD card and SIM card into the card slot.

Please note that the SD card is on the “write” (not locked) position ot-

herwise the camera will not function correctly.

3.3 Do the Camera Settings

Down load the camera set up software ( MC_config.zip) from our web-

site. The specified website is written in the last page of the manual.

3.4 Enter into the TEST Mode

Slide the power switch to the TEST position and enter into the TEST

mode. There are some functions in TEST mode: Custom settings, ma-

nual capture, preview or send MMS manually. The remote control is nee-

ded in this mode.

3.4.1 Custom Settings

Press MENU on the remote control to enter into the menu setting. The

camera can be adjusted to manually customize the camera settings

which display on the LCD screen on the camera. The detailed operations

will be described in the “Advanced Operations” chapter.

3.4.2 Manual Capturing

You can press RIGHT to manually capture photos or record a video and

again RIGHT to stop a video.

3.4.3 Send MMS

When the Send Mode is set as “Manual”, you can send the selected

photo to the preset address in TEST mode. ”Daily Report” and “Instant”

mode are used in the ON mode.

Please note that the images can only be sent and video cannot be sent.

If the SIM card is not inserted, the image cannot be sent as well.

3.5 Power on and Enter into the ON Mode

Slide the power switch to the ON position to power on the camera and

enter into the ON mode. efore entering into the ON mode, you can ad-

just the camera towards the target monitoring area by laser pointer.

After switching on the camera, the motion indication LED (red) light will

blink for about 10s. The 10s is a buffering time before automatically cap-

turing photos or videos, e.g. for closing and locking the bottom cover,

fixing the camera on a tree and walking away.

The camera has the sound recording function, so the sound will be em-

bedded in the video clip while capturing a video.

3.6 SMS Control

When the camera is in ON mode, you can send

text message “#T#” to your camera’s SIM card

number to get an on spot image or use our Android

application tools.

Down load the Android control software

( GTools.zip) from our website. The specified web-

site is written in the last page of the manual.

3.7 SMS Command List

elow is a SMS command list for example.

No Function SMS Command

1 Set Supper User #sg880#4321#Tel. no. administrator#

#mg882#4321#13800138000#

2 Set MMS-Parameters #m#http://mmsc.cingular.com#66.209.11.32#

8080#wap.cingular#account#password#

(The example parameters are for the carrier of AT&T)

3 Set GPRS-Parameters #s#bmctest123@163.com#bmc123#25#

cmnet#smtp.163.com#account#password#

4 Set Normal #n#13800138001#13800138002#13800138003#

Users Phone

5 Set Receive #r#[email protected]#[email protected]#

Email Address bmc3@[email protected]#

6 Get On Spot Photo #t# (Send MMS to phone)

#t#e# (Send picture to Email by GPRS)

7 Check Camera Settings #L#

8 Edit Work Parameters #e#cp#s5#fh#b1#v60#t#l10m#pn#i5s#

Hon08:30-20:30 (cp: camera mode, s5:photo

size fh: video size, b1:photoburst, V60: video-

length, t: set clock, l10m: time lapse, pn: PIR

trigger, i5s: PIR-intervall, mp: send to, Hon:

(work hour)

9 Format TF-Kart #F#

10 Set Administrator`s #P#0000#

Password

11 Help #H#

Inhaltsverzeichnis

Andere Berger & Schroter Wärmebildkamera Handbücher

Berger & Schroter

Berger & Schroter 31277 Bedienungsanleitung

Beliebte Wärmebildkamera Handbücher anderer Marken

Hikmicro

Hikmicro HM-TD3117T-1/Q Bedienungsanleitung

optris

optris PI 160 Bedienungsanleitung

Perfect Prime

Perfect Prime IR0001 Bedienungsanleitung

InfraTec

InfraTec InfraTec Bedienungsanleitung

FLIR

FLIR E4 Bedienungsanleitung

FLIR

FLIR T420-NIST Bedienungsanleitung

ICI

ICI 8000 Series Bedienungsanleitung

Hikmicro

Hikmicro BX20 Bedienungsanleitung

ICI

ICI SOUND DETECT Bedienungsanleitung

Perfect Prime

Perfect Prime IR0175 Bedienungsanleitung

HT THT80 Bedienungsanleitung

ICI

ICI TRACE IR 25 Series Bedienungsanleitung

Qvis

Qvis PX-SDH2010 Bedienungsanleitung

WORKSWELL

WORKSWELL GIS 320 Bedienungsanleitung

FLIR

FLIR Navigator II Bedienungsanleitung

InfraTec

InfraTec VarioCAM Bedienungsanleitung

FLIR

FLIR E6-XT Bedienungsanleitung

FLIR

FLIR Scout TS32r Pro Bedienungsanleitung