Bernina BERNETTE 50 Bedienungsanleitung
Quick on your FEET
BERNINA
Walking
Foot #50
A Walk
in the Park
This quilt is done entirely with
Walking Foot #50. The blocks are
stitched individually, and then
seamed so that the raw edges are
to the front of the quilt. The edges
are covered with bias strips and
the quilt is finished with traditional
binding.
By Nina McVeigh
Draw diagonal lines
connecting the corners of
each block.
Construction
Attach the open-toe sole to Walking Foot #50;
this sole provides extra visibility. Attach Walking
Foot #50 to the sewing machine.
Insert a new #90/14
Embroidery needle into the
machine. Select an Isacord
thread color to complement
each of the 7 block fabrics.
Thread needle and bobbin
with the same thread color.
Select a decorative stitch
and quilt the block along
the diagonals. Choose open
stitches, avoiding satin-
based stitches.
Walking Foot #50 is a very helpful aid for working
with layers of fabric. It can be used with almost any
decorative stitch, making grid quilting much more
interesting! The ability to move the needle to any
position makes precision piecing a breeze. This quilt
is done entirely with Walking Foot #50. The blocks
are stitched individually, and then they are seam so
that the raw edges are to the front of the quilt. The
raw edges are covered with bias strips and the quilt
is finished with traditional binding.
Supplies
• ⅔yard of seven different fabrics
• 1¼ yards fabric for binding & strips between blocks
• 2¼ yards loft batting (or twin size batt)
• Isacord thread in eight colors to coordinate with
quilt fabrics (can use fewer colors if desired)
• Embroidery needle, size 90/14
• Denim needle, size 90/14
• Walking Foot #50 with Guides
• 1” Bias Tape Maker
• Water-soluble glue stick
• Spray starch
• Rotary cutting equipment
• 12½” square quilting ruler
• BERNINA Sewing Machine
Cutting Instructions
Using a rotary cutter, mat and ruler cut the 7 pieces
of fabric into 10¾” squares (8 from each piece).
Cut the batting into twenty-five 10¾” squares.
Preparation
Make 25 quilt sandwiches using the fabric and bat-
ting squares, layering the same print on the top and
bottom of each batting square.
You will have six extra fabric squares left over.
Attach the right hand
guide to Walking Foot
#50 and set it at 3”
from the needle.
Tighten the screw
to hold it in place.
Place the guide on
the previously stitched
line and sew the same
decorative stitch on
each side of the two
diagonal lines.
Stitch all blocks of
the same fabric with
the same thread,
choosing a different
decorative stitch for
each block. Choose
open decorative
stitches, avoiding the
satin-based stitches.
Repeat until you have stitched 25 blocks.
When all blocks are stitched, trim to 10” squares.
Arrange the blocks as desired in a 5 x 5 grid.
With wrong sides
(backs) together, sew
five blocks together in
a row. Guide the edges
with the ¼” seam mark
on the walking foot.
Make 5 rows.
Press seam allowances
open—they will be on
the right side of the quilt.
With wrong sides
(backs) together, stitch
the rows together to
make a square.
Press seam allowances
open.
Select a zigzag stitch
with length = 2mm,
width = 5mm. Zigzag
the seams open using
a thread that is comple-
mentary to all the blocks,
as it will show on the
back of the quilt.
Spray starch the binding fabric. To avoid seaming,
fold the fabric at a diagonal so that when you cut the
bias strips in the next step you will be cutting strips
as long as possible.
Cut eight 1¾”-wide bias strips that are at least 52”
long (seaming if necessary). Set aside the rest of the
fabric.
Load the bias tape
maker with a binding
strip. Pull the fabric
through the bias tape
maker and press as
the folded strip exits
the other end. (I found
that my strips were
more even and consistent when I pressed from the
top side of the fabric.)
Measure the width of
the pressed strip and
divide the measure-
ment in half. Measure
this distance out from
the seam and draw a
placement line for the
edge of the bias strip.
Position a folded bias strip over the seam, aligning
the edge with the marked line. Use a glue stick to
hold the strip in place.
Remove the guide from Walking Foot #50. Remove
the open-toe sole from the foot and attach the
standard sole. Since you will be stitching through
more layers of fabric you may want to change to a
#90/14 Denim needle.
Select a straight stitch
and move the needle
position 2 steps to the
right of center. Place
the quilt under the foot
with the edge of the
bias strip just inside
the right toe of the
foot. Stitch down the
side of the strip.
Repeat for the second
side of the strip.
Lay four strips in one
direction, then lay the
remaining four strips
in the other direction.
From the fabric left over from cutting the bias strips,
cut enough 2½”-wide bias strips to go around the
outer edge of the quilt—about 220”. Seam the bias
strips together. Press the long strip in half length-
wise, wrong sides together.
Place the folded bias
strip on the right side
of the quilt with the
raw edges even. Sew
the folded bias strip
to the quilt using a ⅜”
seam allowance. To
accomplish this, move
the needle position all
the way to the right and guide the raw edge of the
fabric along the outside edge of the foot.
When all of the binding is sewn to the front of the
quilt, press it out away from the quilt. Pull the binding
around to the back of the quilt and stitch along the
inner folded edge to hold the binding in place.
For additional information on Dual Sole
Walking Foot with Guides #50 and other
BERNINA presser feet, attachments, and
accessories, see Feetures, volumes 1-3.
Visit
www.berninausa.com
for additional projects and information.
Andere Bernina Nähmaschine Handbücher
Bernina
Bernina 555 QE Bedienungsanleitung
Bernina
Bernina Bernette 410 Bedienungsanleitung
Bernina
Bernina 950 Industrial Bedienungsanleitung
Bernina
Bernina Bernette 56 Bedienungsanleitung
Bernina
Bernina 570 QE Bedienungsanleitung
Bernina
Bernina 215 Bedienungsanleitung
Bernina
Bernina Q 24 Bedienungsanleitung
Bernina
Bernina B 330 Bedienungsanleitung
Bernina
Bernina Artista 730E Bedienungsanleitung
Bernina
Bernina TLC Bedienungsanleitung
Bernina
Bernina 590 Bedienungsanleitung
Bernina
Bernina deco 330 Fehlerbehebungshandbuch
Bernina
Bernina Artista 730E Bedienungsanleitung
Bernina
Bernina Sewing Machine Bedienungsanleitung
Bernina
Bernina B 780 Bedienungsanleitung
Bernina
Bernina 900 Bedienungsanleitung
Bernina
Bernina 530 Bedienungsanleitung
Bernina
Bernina Bernette 340 deco Bedienungsanleitung
Bernina
Bernina BERNINA 560 Bedienungsanleitung
Bernina
Bernina 820 Bedienungsanleitung
