BESAFE IZi Combi x2 Bedienungsanleitung

Instruction Manual

BeSafe iZi Combi is approved in accordance with ECE R in groups 0 and I, rearward-facing, from 0-18 kg (approx.

0-4 years), and in group 1 forward-facing, from 9-18 kg (approx. 1-4 years), recommended from approx. 2.5-4 years.

BeSafe iZi Combi is installed using the car’s 3-point/2-point seat belt and anchor belts in the rearward-facing position.

In the forward-facing position, it is mounted using the car's 3-point belt.

Before doing anything else, carefully read page 17 under the heading: important!

Sequence for rearward-facing installation:

For fitting the anchor belts in rearward facing position, see page 2.

For mounting in the front seat in rearward facing position, see page 4.

For mounting in the back seat in rearward facing position, see page 8.

Forward-facing:

For mounting in the forward-facing position, see page 13

For placing the child in the seat, see page 15.

NB BeSafe iZi Combi must never be mounted in front

passenger seats with an active airbag. * read more on page 4

44 04

E5 04205E5 04204

Fitting of supplied anchor belts

Alternative A

1. Release the fixing bolts on the car seat’s two forward or rear fixing points.

2. The attachment fittings have to go underneath the slide rail on the car seat

chassis. Insert an attachment fitting on either side of the car seat's two forward

fixing points, see fig. 1b, and tighten hard. 1a. In certain cars, the attachment

fittings will have to be mounted diagonally or at right angles to the car seat slide

rails. See fig. 1a

3. Thread the belt loop on one anchor belt through the opening in one of the two

attachment fittings. Then bring the anchor belt locking device through the belt loop

and pull hard. See fig. 1a

4. Do the same on the opposite side, see fig. 1c

Fig. 1a Fig. 1b Fig. 1c

If the distance between the child seat and the attachment fittings is so

short that it is hard to tighten the anchor belts sufficiently, the fittings can

be moved to the rear/forward fixing points and the anchor belts attached

to these instead.

Alternative B

Secure the two anchor belts round

the car seat's legs/slide rails

1. Secure an anchor belt round each of

the car seat’s rear or front legs by

bringing the locking device of the

anchor belt through the belt loop.

Pull tight. See fig. 2

2. Cross the anchor belts under the

car seat and lock, click.

Fig. 2

R earward-facing

fitting of anchor belts .

R earward-facing

fitting of anchor belts .

Alternative C – Fitting in the front seat

1. Join the two anchor belts together to make

a single belt by putting the lock of belt 1

through the loop of belt 2 and then through

the loop of belt 1.

Pull tight. See fig. 3a

2. Put the middle part of the anchor belt Fig. 3a

Fig. 3a over the inner part of the car seat.

Cross the two ends of the anchor belt under

the car seat and bring them upwards towards

where the child seat is to go. See fig. 3b

3. As the child seat is on top of a soft car seat,

it will always be able to move slightly. In some

cars the child seat will be more stable using

Alternatives A or B.

This method can only be used when the

child seat is mounted on the front seat. Fig. 3b Fig. 3b

Alternative D – Fitting to the back seat

1. Insert the belt loop through the gap between the

seat cushion and the seat back on the front seat.

Then bring the locking device through the belt loop

and tighten. See fig. 4a

2. Do the same on the opposite side of the front seat.

3. When positioning the Fig. 4a

child seat on the car's back

seat, cross the anchor belts

behind before fixing them to

the child seat.

See fig. 4b

Fixing to the front seat

When positioning the child

seat in the car’s front seat,

use the same method for

fitting the belts but they must

cross under the seat as in fig.3b

Fig. 4b

Installation of BeSafe iZi Combi in car’s front seat:

NB Must never be fitted in the front seat

of cars with an active airbag in the

passenger seat.

In some cars the airbag on the

passenger side can be deactivated –

contact your dealer

1. Front brace

Adjust the front brace to the inmost

position, to the stop mark, using the

ratchet lever.

See fig. 5

Fig. 5

2. Mounting of support leg

Assemble the support leg.

See fig. 6

Important that

the belt goes

round the leg

Fig. 6

R earward-facing

in front s eat

3. Positioning in car

Position the BeSafe iZi Combi

in the front seat with the front

brace against the back of the

front seat and the baby seat

against the dashboard.

See fig. 7

For cars with leather interior, we

recommend BeSafe protective

cover to avoid wear or marks

on the leather.

Fig. 7

4. Bring the passenger seat forwards

so that BeSafe iZi Combi touches

the dashboard.

If you wish, put a protective cloth

between the dashboard and the seat.

6. Fitting of anchor belts

Anchor belts must be crossed over

and then brought up to the locking

tongues on the child's seat and

locked, click.

See fig. 9 do not tighten the anchor

belts until the mounting process is complete.

See also fitting alternative

C, page 3

Fig. 9

R earward-facing

in front s eat

Lock the safety leg at the

disired heigh using the

locking bolt.

Make sure the support leg is

in contact with the floor of the

car.

Rearward-facing

in front seat

7. Fitting the front seat belt

Pull out the 3-point belt

and place the hip belt

over the base of the child

seat and behind the

horns on each side.

Fasten the seat belt, click.

See fig. 10

The belt must cross over between the plastic horns.

Fig. 10

11a 11b 11c 11d

8. Pull out the shoulder belt and make it into a loop.

See fig. 11a

9. Thread the loop through the metal part of the red fitting.

See fig. 11b

10. Guide the belt loop into the red slit. See fig. 11c

11. Tighten the belt by pulling the top part down. See fig. 11d

T-0427 iZi COMBI X1 N F GB Mont 16-02-06 09:24 Side 6

12.Adjustment of front brace

Move the front brace outwards

by using the ratchet lever.

See fig. 12 so the front brace

presses tightly into the seat back.

See fig. 13. Adjust the ratchet to

tight/slack position using the knobs

at the top of the ratchet lever.

See red arrows on fig. 12a

Fig. 12 Fig. 12a

13.Moving the mechanism outwards

pushes the front brace in against

the seat back and tightens the

seat belt. See fig. 13

This also provides stable mounting

of the child seat.

Fig. 13

14.Tighten the anchor belts to their maximum.

15.Check that the child seat has

been correctly mounted and is

properly secured with pressure

against the dashboard.

If not, repeat the procedure.

Fig. 14

Rearward-facing

in front seat

T-0427 iZi COMBI X1 N F GB Mont 16-02-06 09:24 Side 7

Rearward-facing

on back seat

Mounting of BeSafe Combi in car back seat:

1. Front brace

Move the front brace to the inmost

position, to the stop mark, using the

ratchet lever.

See fig. 15, fig. 15a and

point 12 on page 7

Fig. 15a Fig. 15

2. Mounting the support leg

Assemble the support leg.

See fig. 16

Important that

the belt goes

round the leg.

Fig. 16

3. Positioning in car

Position the BeSafe iZi Combi on

the back seat of the car with the

front brace towards the back support

rear of the seat. Make sure that the

child seat has support against the

back of the car’s front seat, see fig. 17.

Adjust the support leg downwards so

it reaches the floor of the car.Pull the

safety leg outwards to its maximum

angle so the strap connecting the

seat and the safety leg is tensioned.

See fig. 16

Fig. 17

T-0427 iZi COMBI X1 N F GB Mont 16-02-06 09:24 Side 8

4. Fitting the anchor belts

Anchor belts must be crossed over to meet the locking tongues

on the child's seat and locked, click. See fig. 18. do not tighten the

belts until the mounting process is complete.

Fig. 18

Rearward-facing

on back seat

T-0427 iZi COMBI X1 N F GB Mont 16-02-06 09:24 Side 9

Rearward-facing

on back seat

Fitting of 3-point seat belt on back seat

5. Pull out the 3-point belt and place

the hip belt over the base of the

child seat and behind the horns

on each side.

See figs.19a and 19b

Fig. 19b Fig. 19a

6. Fasten the belt in the belt lock, click.

7. Pull the hip belt forwards and over

the metal hook on the seat base.

See fig. 19c. See green arrow.

8. Pull the shoulder/diagonal belt round

the horn on the side with the seat belt lock.

See fig. 19c with red arrows

Fitting of 2-point fixed seat belt.

Fit as shown in points 5, 6 and 7 Fig. 19c

tighten the 2-point belt.

9. Pull out the shoulder belt and make it into a loop.See fig. 20a

20a 20b 20c 20d

10.Thread the loop through the metal part of the red fitting.

See fig. 20b

11.Guide the belt loop into the red slit. See fig. 20c

12.Tighten the belt by pulling the top part down. See fig. 20d

T-0427 iZi COMBI X1 N F GB Mont 16-02-06 09:24 Side 10

Inhaltsverzeichnis

Andere BESAFE Autositz Handbücher

BESAFE

BESAFE iZi Go Modular Bedienungsanleitung

BESAFE

BESAFE IZI UP X2 STABILITY STRAP - V1.0 Bedienungsanleitung

BESAFE

BESAFE iZi Turn B i-Size Bedienungsanleitung

BESAFE

BESAFE IZI UP Bedienungsanleitung

BESAFE

BESAFE IZI COMFORT ISOFIX Bedienungsanleitung

BESAFE

BESAFE IZI COMFORT ISOFIX Bedienungsanleitung

BESAFE

BESAFE iZi Up FIX Bedienungsanleitung

BESAFE

BESAFE IZI COMFORT ISOFIX Bedienungsanleitung

BESAFE

BESAFE iZi Up X1 Handicap Bedienungsanleitung

BESAFE

BESAFE Handicap Bedienungsanleitung

BESAFE

BESAFE iZi Flex S FIX Bedienungsanleitung

BESAFE

BESAFE IZI UP X2 - V1.0 Bedienungsanleitung

BESAFE

BESAFE IZI COMFORT ISOFIX - CAR LIST 10-2009 Bedienungsanleitung

BESAFE

BESAFE IZI UP Bedienungsanleitung

BESAFE

BESAFE PAD+ Bedienungsanleitung

BESAFE

BESAFE iZi Plus Bedienungsanleitung

BESAFE

BESAFE iZi Twist i-Size Bedienungsanleitung

BESAFE

BESAFE iZi Kid i-Size Bedienungsanleitung

BESAFE

BESAFE iZi Modular i-Size Bedienungsanleitung

BESAFE

BESAFE iZi Kid i-Size Bedienungsanleitung

BESAFE

BESAFE iZi Combi Bedienungsanleitung

BESAFE

BESAFE iZi Go Modular i-Size Bedienungsanleitung

BESAFE

BESAFE iZi Comfort Bedienungsanleitung

BESAFE

BESAFE iZi Twist B i-Size Bedienungsanleitung

Beliebte Autositz Handbücher anderer Marken

Britax

Britax PARKWAY SGL Bedienungsanleitung

JANE

JANE nurse cruiser Bedienungsanleitung

Digicom

Digicom Tippy Pad Bedienungsanleitung

Giordani

Giordani orion 012 Bedienungsanleitung

BRIO

BRIO ZENTO Bedienungsanleitung

Combi

Combi Zeus Turn 8815 Series Bedienungsanleitung

Graco

Graco Car Booster Seat Bedienungsanleitung

Coccolle

Coccolle Atira Bedienungsanleitung

hifold

hifold HF01-GL Bedienungsanleitung

CYBEX

CYBEX SOLUTION X2-FIX Bedienungsanleitung

kiwy

kiwy SLF 123 Bedienungsanleitung

Safety 1st

Safety 1st Summit ISO 30 Bedienungsanleitung

Safety 1st

Safety 1st Grand 2-IN-1 Bedienungsanleitung

Graco

Graco NAUTILUS Bedienungsanleitung

Britax

Britax Multi-Tech BB0-702-00 Bedienungsanleitung

Grammer

Grammer MSG45/421 Betriebsanleitung

Nuna

Nuna REBL PLUS Bedienungsanleitung

Graco

Graco Child Restraint Bedienungsanleitung

BESAFE iZi Combi x2 Bedienungsanleitung

Beliebte Autositz Handbücher anderer Marken