Best Office WS-M3P6 Bedienungsanleitung
ADULT ASSEMBLY REQUIRED
Read all instructions before assembly and use.
Due to the presence of small parts during assembly, keep
out of reach of children untill assembly is complete.
WS-M3P6
www.paylesshere.com
ASSEMBLY INSTRUCTION
4-Tire Wire Shelving Rack
!
BestOfficeR
A B C
D E1 E2
FGH
PARTS LIST
Please read the instruction manual carefully before using it.
Please assemble strictly in accordance with the instruction.
Please double check to the ensure that all parts of the package contents intact.
If you any parts are missing, broken, damaged or worn, stop using this products until
repairs are made and factory replacement parts are installed.
Maximum weight capacity per shelf is 350lbs when weight is equally distributed.
Maximum entire unit weight capacity is 500lbs when equally distributed on casters.
Failure to follow these instructions may result in serious injury or death of
yourself and people around you.
Some of the part are heavy and/or has shape edge, please install it carefully to
avoid hurt you and people around you.
Do not stand on or climb on the shelving unit.Place heavier items on lower shelves and
lighter ones on top shelves.
WARNING
Shelfx 4 x 32 +2 extra
Tapered Lock
x 4 Top Pole
(with pole cap and pole connector preassembled)
x 4 Bottom Pole
(with feet leveler preassembled)
Wheel
non-locking
(for mobile option)
x 2 Wheel
locking
(for mobile option)
x 2
x 1
Spanner
Feet Leveler
x 4 x 4 Pole Connector
(Prerequisites The
installation is complete)
1
2
3
Stationary Option: Screw each feet leveler (F) into the bottom of each bottom pole (D). Turn clock-
wise to screw in place.
Mobile Option: Screw each wheel (E1,E2) into the bottom of each bottom pole (D). Turn clock-wise to
screw in place.
MOBILE
STATIONARY
E2
F
D
D
OR
Attention: The wheel (E1,E2) must be
fully screwed to the botton pole
(D) by wrench
With the tapered end facing up, snap the two halves of a tapered lock (B) at the desired height on
bottom pole (D). Repeat for the remaining bottom poles (D), making sure the tapered locks (B) are
installed at the same grooved line on each bottom pole.
B
D
B
D
Attention：The tapered must be fixed to the groove on the pole, and make sure
the tapered does not slip before installing the shelf
Upward marker
Rest shelf (A) on its side, then insert the bottom poles (D) through the corner holes of the shelf (A).
Turn assembly upright and push the shelf (A) firmly onto the tapered locks (B). Note: Make sure the
lip of shelf (A) is facing down and the levelers (F) on bottom poles (D) are on the floor.
5
E1
D
A
A
E1
E1
E2
E2
4
5
6
MOBILE STATIONARY
Repeat steps 1-3 for the second shelf (A).
A
Screw top pole (C) onto bottom pole(D), hand tighten.
D
C
Repeat steps 1-3 for the remaining shelves.
A
Finish.
Inhaltsverzeichnis
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
