BETCO FOREMAN 17DS Produkthandbuch

CREWMAN™17HD

CREWMAN™20HD

FOREMAN®17DS

FOREMAN®20DS

E83009-00

E83010-00

17”, 20"

Floor Machines

Operator and Parts

Manual

1001 Brown Avenue • Toledo, Ohio 43607-0127

Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.com

E83013-00

E83014-00

Specifications

Length – 24.25 in.

Width – 20. in.

Height – 48 in.

Weight – 85.5 Lbs.

Speed 175 Std, Two Speed 185/330

Pad Diameter 17 or 20 in. Drivers 16” & 19”

Drive motor – 1.5 HP, 120v, 12A, 60 Hz

-1 HP, 120v, 12A, 60 Hz

Two Speed – 1.5 HP, 12 A, 60 Hz

Cord – 14-3 ST, 50 ft.

Hour meter – 0.1 hr resolution

Safety

Read and understand the manual

before operating this machine.

Do not operate in explosive areas or use near

flammable liquids or gases or dust.

Attach only to properly grounded outlet.

Do not expose to rain, store indoors.

Do not operate the machine with a damaged

cord or plug.

Do not block or disconnect the safety lever.

Do not leave the machine plugged in while

unattended.

Unplug the machine before servicing.

Do not put fingers under the pad or pad holder.

Unplug the machine before installing or

removing the pad.

Use only with Suitable Pads or Brushes.

Operating Instructions

Check machine for damage to cord or plug.

Use suitable pads or brushes.

To install or change the pad:

1. Unplug the machine.

2. Tip the machine back on the wheels.

3. Install brush or pad driver.

4. Center the pad on the pad driver.

To operate the machine:

1. Plug into a grounded outlet.

2. Release the handle and lower it.

3. The handle should be locked into a

comfortable position for the operator.

4. Press the safety lever and squeeze the

trigger to start the machine.

5. Do not operate in one place as damage to

the floor or finish could result.

6. Do not operate the machine with the handle

in the upright position.

7. Remove the pad after every use.

8. Store the machine with the pad or brush

removed.

9. Use only new or clean pads and reverse

them as needed.

Maintenance

To maintain appearance – wipe the machine

with a damp cloth after use.

Warning – Unplug the machine before

servicing

This machine is equipped with an hour meter

to signal maintenance intervals of 250 hours. It

will begin flashing at 245 hrs and stop at 255

hrs to signal the operator to check the

following:

1. Check the motor brushes for wear or

excessive arcing on the two speed

machine.

2. Check the cord and electrical system.

3. Check the safety lockout on the trigger.

4. Check the wheels.

Motor Motor

Micro

Switch

Micro

Switch

Rocker

Switch

Spd

Cntrl

Power Cord

Handle Cord Handle Cord

White

Green

Two Speed Machines

Standard Machines

ELECTRICAL

Black

Green

White

Black

11 15

13 7

30/30A

CREWMAN HD

HANDLE ASSEMBLY

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81063

Nyloc Hex Nut 5/16-18 Zinc

E81064

Hex Bolt 1/4-20 x 0.75 Lg Zinc

E81065

Hex Hd Bolt, 1/4-20 x 1-3/4 Lg, Zinc

E81070 Thin Nyloc Nut, 1/4-20, Zinc

E81077

Shoulder Screw, 5/16-18, 3/8 x 1

E81105

Plate, Switch

E81180

Serial Decal

E81379

Spring Washer, 0.375 Crescent

E81713

Flat Washer 0.250 Zinc

E82717

Handle Socket

E82749

Handle Trigger Switchbox

E82750

Switch Box, Handle, Black

E82751

Cover, Switchbox

E83127

Handle Grip 7/8 ID

E83129

Safety Lock

E83130

Spring, Extension

E83132

Handle Cord 14-3

E83137

Handle Lock Cord Hook

E83270

Spring Clip

E83426

Round Screw, 1/4-20 x 1.750 Lg

E83427

Screw 6-32 x 1.00 Lg

E83451

Handle Grip Tube

E83519

Grommet, 1/8 W x 5/8 Groove

E83520

Nyloc Hex Nut 1/4-20 Zinc

E83521

Green Ground Wire, Swing Machine

E83522

Wire Nut, Yellow

E83523

Cable Tie 4.125 Lg x 0.125 W

E83691

Decal, Warning

E83711

Main Handle Tube

30/30A E83723

Decal, Betco Crewman 20HD

E83789

Strain Relief Nut, Metal

E83790

Cord, 14-3 x 50 ft STW Yellow

E85032

Switch, 25 AMP, 1/5 HP, 125 VAC

E89602

Cord Strain Relief, Metal

CREWMAN HD HANDLE PARTS

EP50064 - CAM LOCK ASSEMBLY

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81063

Nyloc Hex Nut 5/16-18 Zinc

E81064

Hex Bolt 1/4-20 x 0.75 Lg Zinc

E81065

Hex Hd Bolt, 1/4-20 x 1-3/4 Lg, Zinc

E81070 Thin Nyloc Nut, 1/4-20, Zinc

E81077

Shoulder Screw, 5/16-18, 3/8 x 1

E81105

Plate, Switch

E81180

Serial Decal

E81379

Spring Washer, 0.375 Crescent

E81713

Flat Washer 0.250 Zinc

E82717

Handle Socket

E82749

Handle Trigger Switchbox

E82750

Switch Box, Handle, Black

E82751

Cover, Switchbox

E83127

Handle Grip 7/8 ID

E83129

Safety Lock

E83130

Spring, Extension

E83132

Handle Cord 14-3

E83137

Handle Lock Cord Hook

E83270

Spring Clip

E83426

Round Screw, 1/4-20 x 1.750 Lg

E83427

Screw 6-32 x 1.00 Lg 2

E83451

Handle Grip Tube

E83519

Grommet, 1/8 W x 5/8 Groove

E83520

Nyloc Hex Nut 1/4-20 Zinc

E83521

Green Ground Wire, Swing Machine

E83522

Wire Nut, Yellow

E83523

Cable Tie 4.125 Lg x 0.125 W

E83691

Decal, Warning

E83711

Main Handle Tube

E83723

Decal, Betco Crewman 20HD 1

E83789

Strain Relief Nut, Metal

E83790

Cord, 14-3 x 50 ft STW Yellow

E85032

Switch, 25 AMP, 1/5 HP, 125 VAC

E89602

Cord Strain Relief, Metal

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81063

Nyloc Hex Nut

5/16-18 Zinc 1

E83133

Cam Lock Handle

E83135

Oval Washer

E83145

Nylon Washer 1/2

ID x 1.25 OD

E83269

Spring Washer

1/2 ID

FOREMAN DS HANDLE ASSEMBLY

34/34A

ITEM NO.

PART NUMBER

DESCRIPTION

Default/Q

TY.

E81063

Nyloc Hex Nut 5/16-18 Zinc

E81064

Hex Bolt 1/4-20 x 0.75 Lg Zinc

E81065

Hex Hd Bolt, 1/4-20 x 1-3/4 Lg, Zinc

E81070 Thin Nyloc Nut, 1/4-20, Zinc

E81077

Shoulder Screw, 5/16-18, 3/8 x 1

E81105

Plate, Switch

E81139

Wire, 16 AWG, Black, 4.00" L, 1

Female QD

E81180

Serial Decal

E81379

Spring Washer, 0.375 Crescent

E81713

Flat Washer 0.250 Zinc

E82717

Handle Socket

E82749

Handle Trigger Switchbox

E82750

Switch Box, Handle, Black

E82751

Cover, Switchbox

E83127

Handle Grip 7/8 ID

E83129

Safety Lock

E83130

Spring, Extension

E83132

Handle Cord 14-3

E83137

Handle Lock Cord Hook

E83270

Spring Clip

E83426

Round Screw, 1/4-20 x 1.750 Lg

E83427

Screw 6-32 x 1.00 Lg 2

E83451

Handle Grip Tube

E83519

Grommet, 1/8 W x 5/8 Groove

E83520

Nyloc Hex Nut 1/4-20 Zinc

E83521

Green Ground Wire, Swing Machine

E83522

Wire Nut, Yellow

E83523

Cable Tie 4.125 Lg x 0.125 W

E83608

DS Rocker Switch, Dual Speed

E83652

DS Heat Sink Rod

E83662

Speed Control, Dual Speed Machine

E83691

Decal, Warning

E83711

Main Handle Tube

34/34A E83747

Decal, Betco Foreman 20DS

E83789

Strain Relief Nut, Metal

E83790

Cord, 14-3 x 50 ft STW Yellow

E85032

Switch, 25 AMP, 1/5 HP, 125 VAC

E89602

Cord Strain Relief, Metal

FOREMAN DS HANDLE PARTS

EP50064 - CAM LOCK ASSEMBLY

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81063

Nyloc Hex Nut

5/16-18 Zinc

E83133

Cam Lock Handle

E83135

Oval Washer

E83145

Nylon Washer 1/2

ID x 1.25 OD

E83269

Spring Washer

1/2 ID

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81063

Nyloc Hex Nut 5/16-18 Zinc

E81064

Hex Bolt 1/4-20 x 0.75 Lg Zinc

E81065

Hex Hd Bolt, 1/4-20 x 1-3/4 Lg, Zinc

E81070 Thin Nyloc Nut, 1/4-20, Zinc

E81077

Shoulder Screw, 5/16-18, 3/8 x 1

E81105

Plate, Switch

E81139

Wire, 16 AWG, Black, 4.00" L, 1 Female QD

E81180

Serial Decal

E81379

Spring Washer, 0.375 Crescent

E81713

Flat Washer 0.250 Zinc

E82717

Handle Socket

E82749

Handle Trigger Switchbox

EP50301

Switchbox Cover, Dual Speed

E82751

Cover, Switchbox

E83127

Handle Grip 7/8 ID

E83129

Safety Lock

E83130

Spring, Extension

E83132

Handle Cord 14-3

E83137

Handle Lock Cord Hook

E83270

Spring Clip

E83426

Round Screw, 1/4-20 x 1.750 Lg

E83427

Screw 6-32 x 1.00 Lg

E83451

Handle Grip Tube

E83519

Grommet, 1/8 W x 5/8 Groove

E83520

Nyloc Hex Nut 1/4-20 Zinc

E83521

Green Ground Wire, Swing Machine

E83522

Wire Nut, Yellow

E83523

Cable Tie 4.125 Lg x 0.125 W

E83608

DS Rocker Switch, Dual Speed

E83652

DS Heat Sink Rod

E83662

Speed Control, Dual Speed Machine

E83691

Decal, Warning

E83711

Main Handle Tube

E83747

Decal, Betco Foreman 20DS

E83789

Strain Relief Nut, Metal

E83790

Cord, 14-3 x 50 ft STW Yellow

E85032

Switch, 25 AMP, 1/5 HP, 125 VAC

E89602

Cord Strain Relief, Metal

11/11A

14 3

6/6A

BASE ASSEMBLY

ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

E81062

Flat Washer 5/16 USS, Zinc

E81067

Lock Washer 5/16 Zinc

E81068

Washer, Fender 1/4 Zinc

E81071

Nylon Rivet, Ribbed Shank 0.281

E81124

Wheel, 5.00 OD x 3/4 ID

6/6A

E81129

Base, 20 in, Low Speed

E83136

Bracket, Flat Handle

E83141

Bumper 3.5 ft

E83143

Axle Cap 1/2 in

E83145

Nylon Washer 1/2 ID x 1.25 OD

11/11A E83191

Motor, 1.5 HP, AC

E83269

Spring Washer 1/2 ID

E83379

Axle, 0.5 x 13.875

E83425

Truss Head Screw, 1/4-20 x 3/4 Lg

E83452

Axle, 0.500 OD x 12.375 Lg, Zinc

E83641

Hex Hd Bolt, 5/16-18 x 1-1/2 Lg, Zinc

E83773

Decal, Betco Equipment (for

Crewman only)

E81127

Base, 17 in, Low Speed

E81106

Motor, 1.5HP-2 Speed Floor Machine

BASE PARTS

FOREMAN DS COVER

CREWMAN HD COVER

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81062

Flat Washer 5/16 USS, Zinc

E81067

Lock Washer 5/16 Zinc

E81068

Washer, Fender 1/4 Zinc

E81071

Nylon Rivet, Ribbed Shank 0.281

E81124

Wheel, 5.00 OD x 3/4 ID

E81129

Base, 20 in, Low Speed

E81127

Base, 17 in, Low Speed

E83136

Bracket, Flat Handle

E83141

Bumper 3.5 ft

E83143

Axle Cap 1/2 in

E83145

Nylon Washer 1/2 ID x 1.25 OD

E83191

Motor, 1.5 HP, AC

11A

E81106

Motor, 1.5HP-2 Speed Floor Machine

E83269

Spring Washer 1/2 ID

E83379

Axle, 0.5 x 13.875

E83425

Truss Head Screw, 1/4-20 x 3/4 Lg

E83452 Axle, 0.500 OD x 12.375 Lg, Zinc

E83641

Hex Hd Bolt, 5/16-18 x 1-1/2 Lg, Zinc

E83773

Decal, Betco Equipment (for Crewman only)

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81078

Lock Washer 0.250 Zinc

E81713

Flat Washer 0.250 Zinc

E83147

Hour Meter

E83570

Pan Head Screw 1/4-20 x

1.0 Lg 4

E83642

Cover, Motor, Red, Low

Speed

ITEM

NO.

PART

NUMBER

DESCRIPTION

QTY.

E81140

Cover, Motor, 9 OD x 1.65

E81526

Screw 10-32 x 1/2, Phillips

Trust Head 18-8

Andere Handbücher für FOREMAN 17DS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere BETCO Bodenreinigungsmaschine Handbücher

BETCO

BETCO CREWMAN DC2000 Produkthandbuch

BETCO

BETCO Stealth ASD26BT Produkthandbuch

BETCO

BETCO ex13100 Bedienungsanleitung

BETCO

BETCO PB21-11 Bedienungsanleitung

BETCO

BETCO XT3 27 Bedienungsanleitung

BETCO

BETCO GENIE APS Bedienungsanleitung

BETCO

BETCO MOTOMOP Produkthandbuch

BETCO

BETCO CRETE Rx CP30 Produkthandbuch

BETCO

BETCO OPTIMA XR Series Produkthandbuch

BETCO

BETCO FOREMAN 20 HD Bedienungsanleitung

BETCO

BETCO WS24 Bedienungsanleitung

BETCO

BETCO CREWMAN AS20B Bedienungsanleitung

BETCO

BETCO E12327-00 BIG BERTHA XSM30 Produkthandbuch

BETCO

BETCO Crewman DC200 Bedienungsanleitung

BETCO

BETCO B20TR Bedienungsanleitung

BETCO

BETCO Optima QT E12317-00 Bedienungsanleitung

BETCO

BETCO PREDATOR SERIESE Produkthandbuch

BETCO

BETCO PB24 Bedienungsanleitung

BETCO

BETCO Pourman 25 Bedienungsanleitung

BETCO

BETCO Big Bertha Bedienungsanleitung

BETCO

BETCO xt3-27 Bedienungsanleitung

BETCO

BETCO STEALTH ASD20B Produkthandbuch

BETCO

BETCO Foreman 1600 Bedienungsanleitung

BETCO

BETCO STEALTH ASD20B Produkthandbuch

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch