BFT RIGEL 5 Bedienungsanleitung

Rigel 5 v1.7 QRG

Quick reference guides are not a replacement for the supplied instructions, they are supplementary

Read and understand the installer warnings in the main instruction document first

Always apply good, safe, state of the art engineering and electrical installation principles

Safety of the completed installation is the ultimate responsibility of the installer

This product is not suitable for DIY use and should only be installed and maintained by a trained, skilled, professional installer

www.metalines.com

[email protected]

Menu System

www.metalines.com

[email protected]

Parameters;

Adjustable numeric settings (formerly on pots)

Logic;

Function ON/OFF settings (formerly on dip switches)

Radio;

Transmitter storage

Language;

Panel language selection

Default;

Restore panel Parameter and Logic settings to factory

default

Menu Layout

www.metalines.com

[email protected]

Essential Parameters

No. of down

button presses

For more options and detail see main instructions

www.metalines.com

[email protected]

Essential Logics

No. of down

button presses

For more options and detail see main instructions

The 12v dc lock output can

accommodate 1 x 0.5A magnetic

lock or 1 x 2A impulse lock

www.metalines.com

[email protected]

Essential Radio and Language

“Hidden Button”

www.metalines.com

[email protected]

•Set the motors in place on the correct geometry

(plumb with top hinge for under ground or A = B for rams)

•Install any gate stops to be used (mandatory for hydraulics-except Lux FC)

•Manual release and set limit switch positions (Igea only)

•Set the gates at 45° (half open/shut) and close the manual releases

•Connect up the motor and supply cables

(Single motor systems use only motor 2 connections)

•Do not connect any accessories at this stage and leave all jumpers in place

•Run the Quick menu – press OK once

•Run the motors (1 sec. link 30/31) – check that both are opening and not closing

•Swap terminals 5&6 or 8&9 if either gate moves in the close direction

•Close both gates on manual & close the manual releases

•Run the gates through several cycles and check settings

•run the traditional menu to make adjustments – press OK twice rapidly

•Add accessories one at a time and test each one before moving on

Method

www.metalines.com

[email protected]

Typical

Wiring

Example

www.metalines.com

[email protected]

Wiring Connections

www.metalines.com

[email protected]

Machine Directive Compliance

Hydraulic & Electromechanical;

1. Adjust parameter to enable M1 to close 600mm before M2

Hydraulic;

2. Adjust the force at the leading edge with the CLOSE pressure screw to give

under 400N in the last 500mm of closing (utilise hydraulic slow down if available)

Electromechanical;

2. Adjust parameter to give 600mm of slow space

3. Adjust parameter to give under 400N during slow down

Hydraulic & Electromechanical;

Fit a safe edge to the leading edge of M2

Run a full set of tests and address all other risks as appropriate

Set Logics

www.metalines.com

[email protected]

Andere Handbücher für RIGEL 5

Inhaltsverzeichnis

Andere BFT Bedienfeld Handbücher

BFT

BFT TLB Bedienungsanleitung

BFT

BFT THALIA BT A80 Bedienungsanleitung

BFT

BFT SHYRA AC SL Bedienungsanleitung

BFT

BFT LIBRA-C-LX Bedienungsanleitung

BFT

BFT LEO MV D Bedienungsanleitung

BFT

BFT VENTIMIGLIA NS Bedienungsanleitung

BFT

BFT Rigel 6 QRG Bedienungsanleitung

BFT

BFT SHYRA AC F SL Bedienungsanleitung

BFT

BFT ALCOR N Bedienungsanleitung

BFT

BFT NETTUNO B Bedienungsanleitung

BFT

BFT Q.BO PAD Bedienungsanleitung

BFT

BFT SHYRA AC SL Bedienungsanleitung

BFT

BFT THALIA L Montage- und Bedienungsanleitung

BFT

BFT ALTAIR-P Bedienungsanleitung

BFT

BFT THALIA P Bedienungsanleitung

BFT

BFT LUNA AC B Bedienungsanleitung

BFT

BFT RIGEL 6 Bedienungsanleitung

BFT

BFT HYDRA Bedienungsanleitung

BFT

BFT LIBRA-C-MA Bedienungsanleitung

BFT

BFT SIRIO CBA 230 INV Bedienungsanleitung

BFT

BFT ALCOR AC A Bedienungsanleitung

BFT

BFT THALIA P Bedienungsanleitung

BFT

BFT LEO B CBB DL2 3 230 L02 Bedienungsanleitung

BFT

BFT HYDRA-R Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten