Biamp VOLTERA A Series Montageanleitung

[email protected]

www.biamp.com

VOLTERA A Series

Installation and Setup Guide

Product Information Sources

•This guide covers installing and setting up the amplifier.

•Please see the product datasheets on Biamp.com for each Voltera amplifier’s

specifications.

•If you are installing the amplifier in an AV system managed by a Tesira DSP device,

you will need a copy of the Tesira Design Software. See page 17 for details.

Included in the Box

•0.3” euroblock connector plugs for the amplified outputs (yellow)

o2 plugs for the 2-channel amps. 4 plugs for the 4-channel amps.

•3.81mm audio input mating plugs

•Detachable IEC Power cord

•4 adhesive feet

•1 single device rack mounting bracket, 1 device rack mounting bracket, and 4

surface-mounting brackets.

A 300.2 A 600.2 A 300.4 A 600.4 Analog Amplifiers

2 Voltera Amplifiers Installation and Setup Guide

Installation Considerations

•Install the device away from heat sources, such as vents, radiators, heat registers, and

stoves.

•Do not exceed the maximum ambient operating temperature of 32° - 104° F (0° - 40° C).

•Avoid installing near water or steam.

Device Layout

Front Panel

Channels status display

(The number of channels varies by amplifier type.)

Amplifier type identifier

Power indicator

3 Voltera Amplifiers Installation and Setup Guide

Front Panel LED Indicators

Power Indicator

Off

The amplifier is off.

Green

The amplifier is powered.

Yellow

The amplifier is asleep.

Channel Status Indicators

Off

Green

Yellow

Red

temp

Channel within safe

temperature limits

N/A

Fan speed medium

Fan speed max

limit

Channel within safe

limits

N/A

Channel limiting

low to medium

Channel

limiting high

signal

No signal

Signal

present*

Signal 6 dB from

maximum output

Signal 1 dB

from max

output

mute

Channel unmuted

N/A

Mute active

*A minimum signal strength of -56 dBu is required to register as present.

Back Panel Channel Status Indicators

Signal present is indicated with green. Yellow and red indicate

the signal is strong enough to engage the limiter function.

These states are also shown on the channel’s front panel

signal and limit indicators. See the chart above.

4 Voltera Amplifiers Installation and Setup Guide

A 300.2 and A 600.2 Back Panels

The amplifiers share an identical panel layout.

A 300.4 and A 600.4 Back Panels

Limit / signal indicators

2, 3-pin input ports

Logic input / output connectors

Voltage control input

Attenuator and high pass filter switches

2 speaker output ports

Channel 2 gain control

Channel 1 gain control

Factory config port

(not for use)

Channels 3 and 4 gain controls

4, 3-pin input ports

Logic input / output connectors

Voltage control input

Attenuator and high pass filter switches

4 Speaker output ports

Channel 2 gain control

Channel 1 gain control

Factory config port

(not for use)

5 Voltera Amplifiers Installation and Setup Guide

Included Mounting Brackets

1 Single-Device Rack Mounting Bracket

1 Device Rack Mounting Bracket

4 Surface Mounting Brackets

6 Voltera Amplifiers Installation and Setup Guide

Installation and Setup Overview

Installation

Perform the procedures described in the Installation chapter to install the amplifier on a flat

horizontal surface or in an AV equipment rack.

✓Install in a location.

•Freestanding, page 7

•Surface mount, page 8

•A single amplifier in a 19-inch rack, page 9

•Dual amplifiers in a 19-inch rack, page 10

19-inch rack installation configurations using the included mounting brackets

✓Connect the amplifier.

•Connect to its input, output, and other relevant devices in the system, page 12.

oThis section includes a description of the port functions and technical details.

oOptional: Adjust the output gain levels.

oSet the output power modes on each channel and set the High Pass Filter to on

or off.

•Attach and plug in the power cord, page 16.

Amplifier Setup

Perform the procedures in the Setup chapter to configure the amplifier for use in a Tesira

software-administered AV system.

✓Configure the amplifier.

•Download the Tesira Design Software, page 17.

•Add the amplifier to the Tesira system and select its output speaker types, page 18.

7 Voltera Amplifiers Installation and Setup Guide

Installation

Install Option: Freestanding

Place the amplifier on a flat horizontal surface.

1. Verify the surface is flat and level, and that the amplifier's power cord and connections

will be safely out of the way to avoid snagging, yanking, or crushing.

2. Attach the 4 included adhesive feet to the bottom of the amplifier. The 4 feet should be

attached near the 4 corners.

3. Place the amplifier on the surface.

Advance to the connect the amplifier procedure on page 12.

8 Voltera Amplifiers Installation and Setup Guide

Install Option: Surface Mount

Secure the amplifier to a flat surface using the surface mount brackets.

8x - M3x5mm screws

1. Verify the surface is flat and level, and that the amplifier’s power cord and connections

will be safely out of the way to avoid snagging, yanking, or crushing.

2. Use the included screws to fasten the 4 surface mounting brackets to the 4 attachment

points on the bottom of the amplifier.

Note: Use only the provided M3 x 5mm screws. Using incorrect screws may damage the

device.

3. Place the amplifier on the surface and fasten the mounting brackets to the surface.

Advance to the connect the amplifier procedure on page 12.

9 Voltera Amplifiers Installation and Setup Guide

Install Option: A single amplifier in a 19-inch AV rack

Install a single amplifier by itself in an AV equipment rack using the included single-device

mounting bracket and the device mounting bracket.

4x –M4 x 8mm screws

1. Verify the installation rack space meets the temperature and spacing requirements in

the Installation Considerations section on page 2.

2. Attach the single-unit mounting bracket to the left or right side of the amplifier.

3. Attach the device mounting bracket to the opposite side of the amplifier.

4. Place the amplifier in the rack and use 2 of the included screws to secure the mounting

plate to the rack.

Advance to the Connect the Amplifier procedure on page 12.

10 Voltera Amplifiers Installation and Setup Guide

Option: Dual devices in a 19-inch rack

Install two amplifiers side by side in a standard AV rack using the device mounting bracket

included with each unit and two of the included surface mounting brackets.

1. Verify the installation rack space meets the temperature and spacing requirements in

the Installation Considerations section on page 2.

2. Place both amplifiers side by side on their tops, with the bottom facing up. You are

about to fasten the amplifiers together for installation, so their front panels must face in

the same direction.

Note: Use only the provided M3 x 5mm screws. Using incorrect screws may damage the

device.

8x - M3 x 5mm screws

3. Attach 2 of the surface mounting brackets to the bottom of the 2 amplifiers on the

surface-mount attachment points where the amplifiers meet. Each bracket should cover

the adjoining mount points on both amplifiers.

Andere Handbücher für VOLTERA A Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Biamp Verstärker Handbücher

Biamp

Biamp VOCIA VA-8600 Bedienungsanleitung

Biamp

Biamp VOCIA VA-8600 Bedienungsanleitung

Biamp

Biamp Vocia VA-2060 Bedienungsanleitung

Biamp

Biamp Tesira AMP-4175R Bedienungsanleitung

Biamp

Biamp 1200 Bedienungsanleitung

Biamp

Biamp CPA 130 Bedienungsanleitung

Biamp

Biamp MCA SERIES Bedienungsanleitung

Biamp

Biamp 2500 Bedienungsanleitung

Biamp

Biamp AMP-A460H Bedienungsanleitung

Biamp

Biamp VOLTERA A Series Montageanleitung

Biamp

Biamp AUDIAFUSION Bedienungsanleitung

Biamp

Biamp Tesira AMP-450P Bedienungsanleitung

Biamp

Biamp CPA650 Bedienungsanleitung

Biamp

Biamp Xa Series Bedienungsanleitung

Biamp

Biamp CMA Series Bedienungsanleitung

Biamp

Biamp Tesira SERVER Bedienungsanleitung

Biamp

Biamp Vocia VA-8150CV Bedienungsanleitung

Biamp

Biamp PREZONE2 Original Betriebsanleitung

Biamp

Biamp Vocia VFOM-1 Bedienungsanleitung

Biamp

Biamp Vocia VFOM-1 Bedienungsanleitung

Biamp

Biamp T Series Bedienungsanleitung

Biamp

Biamp CPA650 Bedienungsanleitung

Biamp

Biamp VOCIA VA-8600 Bedienungsanleitung

Biamp

Biamp TesiraXEL 1200.2 Original Betriebsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung