Billion BiPAC 5200S Series Bedienungsanleitung

BiPAC 5200 series

5200S, 5200, 5200G-R4, 5200G-RA, and

5200N

ADSL2/2+ Modem/Routers

UK Quick Install Guide

LAn Auto Install CD is supplied

with this product to assist with

your connection. Please ensure

you follow the instructions closely

in this guide in order to minimize

problems. This guide covers only

the initial Internet set-up. Please

refer to the full User Manual on the

CD-ROM for more advanced

settings. This guide is based on the

Billion BiPAC 5200G ADSL2/2+

Modem/Router so be aware that for

other models in the 5200 series the

screen shots will vary slightly.

www.billion.uk.com

QUICK INSTALL GUIDE

Billion 5200G ADSL2/2+ Modem/Router Installation

1.1 Starting out:

Before you can establish an Internet connection through your Billion 5200G

ADSL2/2+ Modem/Router make sure you have the following:

1. A Computer or Notebook with an installed Network Adaptor (sometimes called

an Ethernet Adaptor, Network Card or NIC)

2. An ADSL or DSL service account and configuration information provided by

your Internet Service Provider (ISP). You should need only a User Name and

Password, but you can check with your ISP to see if you require any of the

other following configuration parameters to connect your Billion 5200G

ADSL2/2+ Modem/Router to the Internet :

a. ISP User Name and Password

b. VPI/VCI parameters

c. Multiplexing Method

d. Host and Domain Names

e. ISP Domain Name Server ( DNS ) Address

f. Fixed or Static IPAddress.

1.2 Steps for Connection:

The following are the steps to properly connect your Billion 5200G ADSL2/2+

Modem/Router:

1. Turn off your computer.

2. If you do not have an ADSL faceplate installed by your service provider, you

must ensure ADSL splitters (also called microfilters or filters) are fitted to all

telephone sockets in use.

3. Connect the supplied ADSL RJ-11 cable from the splitter/filter of your chosen

telephone socket (or ADSL faceplate if you have one) to the ADSL Port of your

Billion 5200G ADSL2/2+ Modem/Router (or LINE Port if you have no ADSL

Port)

4. Connect the Ethernet cable (RJ-45) from one of the Ethernet ports of your Billion

5200G ADSL2/2+ Modem/Router to the Network Adaptor in your computer.

5. Connect the Power adaptor to the Billion 5200G ADSL2/2+ Modem/Router and

plug the other end into a Power outlet. Power up the unit.

6. Turn on your computer. Please allow up to 45 seconds for your Network Adaptor

to locate the Router. Please wait for the ADSL light on the front of the router to

turn from slow flashing to rapid flashing or solid – this may take up to 1 minute

(see 3.1 Troubleshooting the connection).

7. You are now ready to configure the Billion 5200G ADSL2/2+ Modem/Router.

8. Please insert the supplied Configuration Utility CD into your computer’s

CD/DVD drive now, and follow the simple on-screen instructions to connect your

Billion 5200G ADSL2/2+ Modem/Router. This process may take up to 5 minutes.

All you need to do is to follow the instructions on screen and when prompted

enter your User Name and Password as supplied by your Service Provider and

set up your wireless security as required. No other changes should be necessary.

9. You should now be connected to your Service Provider. This completes the initial

connection and wireless configuration of the modem.

10. If you have not been supplied with a Configuration Utility CD or the supplied

CD is not working, please configure your Router manually by following the

instructions for Manual Configuration in section 2.1.

2.1 Manual Configuration:

1. Open Internet Explorer or your default web browser and type

http://192.168.1.254 on the address bar (where you would normally enter the

web site address) as per the illustration below.

2. You will be presented with a user name and password prompt.* Simply enter

user name as admin, password as admin and click OK.

* If the user name and password prompt box does not appear make sure

that any firewall or anti-virus such as Trend Micro or Norton is disabled.

Also ensure that your Internet settings are correct. (In Internet Explorer go

to Tools/Internet Options/Connections and make sure “Never dial a

Connection” is checked. Then Click on the LAN settings and ensure

“Automatically detect settings” is checked and all other fields are blank.

Then go to Tools/Internet Options/Security and return your Security

settings to “default”. )

3. This will take you to the modem’s Home Page and will show the modem’s

Status.

4. Click on Interface Setup to access the manual configuration fields. Under the

heading ATM VC ensure the Virtual Circuit is PVC0, Status is Activated, the

VPI setting is 0 and the VCI setting is 38. Under the heading Encapsulation

make sure PPPoE/PPPoA is checked.*

* Standard UK settings are VPI 0, VCI 38 and Encapsulation PPPoA VC-

Mux. A small number of Service Providers do however have their own

proprietary settings. In this case please contact your Service Provider to

confirm their configuration parameters.

5. Under the heading PPPoE/PPPoA enter your User Name and Password as

supplied by your Service Provider and check the Encapsulation is PPPoA VC-

Mux.

6. Click the Save button at the bottom of the page.

7. After the settings are saved you should be connected to you Service Provider.

8. Under Interface Setup you can click on Wireless should you wish to access

the advanced wireless configuration fields.

9. Confirm any changes you make to your wireless settings by clicking Save.

10. For further advanced configuration please access the full manual on the CD

provided.

3.1 Troubleshooting the connection:

1. Check that the ADSL light on the front of the router has turned to rapid

flashing or solid. This can take up to 1 minute after switching on. (If the

ADSL light continues to flash slowly then the router is not detecting an ADSL

signal and you should contact your Service Provider immediately)

2. Ensure your username and password are correct – your username should read

[email protected] (or something similar).

3. Ensure you have a filter attached to the master socket, and check there are no

phones connected to any extensions that do not have a filter.

If you still can’t get a connection after checking the above – disconnect all phones,

sky boxes, fax machines etc., double–check that all cables are correctly connected and

filters properly attached, restart the router, and try again.

If this still fails then we suggest you contact your Service Provider for further advice.

Telephone Support for Internet Access ONLY is available during office hours from

Mon-Fri 10am–5pm on 0870-8501528. If you are successfully connected to the

Internet and have a support query please visit www.billion.uk.com/esupport and

submit a ticket.

This symbol on the product or in the instructions means that your electrical and electronic

equipment should be disposed at the end of its life separately from your household waste.

There are separate collection systems for recycling in the EU.

For more information, please contact the local authority or your retailer where you purchased

the product.

Andere Handbücher für BiPAC 5200S Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Billion Netzwerk-Router Handbücher

Billion

Billion BiPAC 7202 Bedienungsanleitung

Billion

Billion BiPAC 8700VAX(L)-1600 Bedienungsanleitung

Billion

Billion Bipac 74 Series Bedienungsanleitung

Billion

Billion BiPAC 5200 Bedienungsanleitung

Billion

Billion BiPAC 7800(N) Bedienungsanleitung

Billion

Billion BiPAC 7800GZ(L) Bedienungsanleitung

Billion

Billion BiPAC 7401V(G)P R4 Bedienungsanleitung

Billion

Billion BIPAC-74x GE Series Bedienungsanleitung

Billion

Billion BiPAC 7820NZ Bedienungsanleitung

Billion

Billion BiPAC 8500/8520 Bedienungsanleitung

Billion

Billion BiPAC 7401V(G)PX Bedienungsanleitung

Billion

Billion BiPAC 7404VNOX Bedienungsanleitung

Billion

Billion BiPAC 7402R2 Bedienungsanleitung

Billion

Billion BiPAC 7404VNOX Bedienungsanleitung

Billion

Billion BiPAC 5200 Bedienungsanleitung

Billion

Billion BiPAC 7401V(G)PX Bedienungsanleitung

Billion

Billion BiPAC 9800 Bedienungsanleitung

Billion

Billion BiPAC 7800(N) Bedienungsanleitung

Billion

Billion BiPAC 8500 Bedienungsanleitung

Billion

Billion BiPAC 5200G Series Bedienungsanleitung

Billion

Billion BiPAC 7402R2 Bedienungsanleitung

Billion

Billion VoIP/(802.11g) ADSL2+ Router BiPAC 7300VGP Bedienungsanleitung

Billion

Billion BiPAC 7800 Bedienungsanleitung

Billion

Billion BiPAC 7401VP Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung