Billy Goat LB351 Bedienungsanleitung

Part No 901014 Form No F072111C

LB Owner’s Manual

BILLY GOAT LB VACUUM

Owner's Manual

LB351, LB61

Optional Accessories

HOSE KIT

4"(102mm) x

7' (3.05m)

For

vacuuming in

hard to reach

areas.

HOSE

CONNECTOR

KIT

P/N 900460

To connect two

lengths of 4”

hose (hose not

included).

P/N 890045

BAG SUPPORT

KIT

Extends bag life

by keeping bag

from dragging

ground.

P/N 900645

STANDARD

FELT DEBRIS

BAG

For use in

dusty

conditions.

P/N 900719

OPTIONAL

TURF DEBRIS

BAG

For use in

leaves and

grass in non-

dusty

conditions.

P/N 90072

Part No 901014 Form No F072111C

LB Owner’s Manual

CONTENTS

SPECIFICATIONS AND SOUND/ VIBRATION 3

INSTRUCTIONLABELS 4

PACKING CHECKLIST & ASSEMBLY 5

OPERATION _6

MAINTENANCE AND TROUBLESHOOTING 7

ILLUSTRATED PARTS & PARTS LISTS 8-9

Part No 901014 Form No F072111C

LB Owner’s Manual

Specifications

LB61 LB351

Engine: cc 190cc 158cc

Engine: Type B & S QUANTUM B & S 500 series

Engine: Model 112K020124E1 10T502 9305 14

Engine: Fuel Capacity 1.5 qt. (1.4 L) .9 qt (.85 L)

Engine: Oil Capacity 0.63 qt. (0.6 L) 18 to 20 oz. (.54-.59L)

Total Unit Weight: 63# (28.58 kg) 57# (25.85 kg)

Overall Length 47” (1.19 m) 47” (1.19 m)

Overall Width 21.5” (0.55 m) 21.5” (0.55 m)

Overall Height 40.5” (1.02 m) 40.5” (1.02 m)

Max. operating slope 200200

Sound in accordance with

2000/14/EEC standards 105dBa 105dBa

Sound at operators ear 85dBa 85dBa

Vibration at operator

position 1.06g (10.4m/s2) 1.06g (10.4m/s2)

SOUND

SOUND LEVEL 85 dB(a) at Operator Ear

Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 12-12-2002 under the conditions listed below.

Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for the sound

power level for your model.

VIBRATION DATA

VIBRATION LEVEL 1.06g (10.4m/s2)

Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test

equipment. Tests were performed on 12-12-06 under the conditions listed below.

General Conditions: Sunny

Temperature: 57oF (14.3oC)

Wind Speed: 12 mph (19.3 kmh)

Wind Direction: Southeast

Humidity: 46.4%

Barometric Pressure: 30.10”H

(

764.6 mm H

General Conditions: Sunny

Temperature: 57oF (14.3oC)

Wind Speed: 12 mph (19.3 kmh)

Wind Direction: Southeast

Humidity: 46.4%

Barometric Pressure: 30.10”Hg (764.6 mm Hg)

105 dB

Part No 901014 Form No F072111C

LB Owner’s Manual

INSTRUCTION LABELS

The labels shown below were installed on your BILLY GOAT ®LB Vacuum. If any labels are damaged or missing, replace them before operating

this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The

correct position for each label may be determined by referring to the Figure and Item numbers shown.

LABEL DANGER KEEP HANDS LABEL EAR EYE BREATHING ITEM #23 DANGER FLYING DEBRIS

AND FEET AWAY P/N 890254 ITEM # 73 P/N 810736

ITEM #67 P/N 400424

LABEL READ MANUAL LABEL EXPLOSIVE FUEL DEBRIS BAG LABEL

ITEM #76 P/N 430363 ITEM # 75 P/N 400268 ITEM #10

ENGINE CONTROLS & LABELS

Throttle Control

Choke Control

BRIGGS & STRATTON

Briggs engines have a primer

button carburetor rather than

choke type carburetor.

Part No 901014 Form No F072111C

LB Owner’s Manual

PACKING CHECKLIST

Your Billy Goat LB Vacuum is shipped from the factory in one carton, completely assembled except for the

upper handle, debris bag.

PUT OIL IN ENGINE BEFORE STARTING

ASSEMBLY

READ all safety instructions before assembling unit.

TAKE CAUTION when removing the unit from the box the Handle Assembly is attached by

cables and folded over

Your Billy Goat is shipped from the factory in one carton, completely assembled except for the debris bag.

1. ROTATE upper handle into upward position and securely tighten knobs. Machine can be stored with handle

folded in down position.

2. UNFOLD the debris bag (item 10) and fasten bag neck onto exhaust discharge opening.

3. ATTACH bag hanger straps to loops (item 38), preassembled to upper handle.

4. CONNECT spark plug wire.

Boxing Parts

Checklist

Debris Bag

P/N-900718

Literature Assy

P/N-901008

Briggs & Stratton

6.0 HP Quantum

Briggs & Stratton

500 Series

PARTS BAG &

LITERATURE ASSY

Warranty card P/N- 400972, Owner’s Manual P/N-901014, General Safety and Warnings Manual P/N-

rmi

N-

900

atu

LB A

ccesso

900

714.

Part No 901014 Form No F072111C

LB Owner’s Manual

OPERATION

VACUUMING OPERATION

VACUUM NOZZLE HEIGHT ADJUSTMENT:is raised and lowered by adjusting front wheel height control.

FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle. NOTE:

Never bury nozzle into debris.

CLEARING A CLOGGED NOZZLE & EXHAUST:Turn engine off and wait for impeller to stop completely

and disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp

materials. Reconnect spark plug wire.

DEBRIS BAG

Debris bags are normal replaceable wear items.

Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.

An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional

Accessories shown on page 1).

DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition

new bag. Your new bag requires a break-in period to condition the pores of the material against premature blockage.

The entire bag surface serves as a filter, and must be able to breath to have good vacuum performance.

Be sure engine has come to a complete stop before removing or emptying bag.

This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings

page 2 & 3).

However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas.

Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your

machine's ability to vacuum in dusty conditions:

•Run machine at idle to quarter throttle.

•The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup

performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake

bag free-of-dust.

•Machine or pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before

use.

Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned.

•DO NOT leave debris in bag while in storage.

COMPOST

Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to

provide enriched soil for later use as fertilizer in gardens and flower beds

NOTE: Allow green chips to dry before spreading around living plants.

Part No 901014 Form No F072111C

LB Owner’s Manual

MAINTENANCE

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation Every Use (daily) Every 5 hrs (daily)

Inspect for loose, worn or damaged parts. z

Clean Debris bag z

Check bag strap tightness z

Engine (See Engine Manual)

Check for excessive vibration z

Troubleshooting

Problem Possible Cause Solution

Abnormal vibration. · Loose or out of balance impeller or

loose engine · Check impeller and replace if required.

Check engine

Will not vacuum or has poor

vacuum performance · Dirty debris bag. Nozzle height set too

high or low. Hose kit cap missing.

Clogged nozzle or exhaust. Excessive

quantity of debris.

· Clean debris bag. Shake bag clean or

wash. Adjust nozzle height. Check for

hose kit cap. Unclog nozzle or exhaust.

Allow air to feed with debris

Engine will not start. · Throttle in off position. Out of gasoline.

Bad or old gasoline. Sparkplug wire

disconnected. Dirty air cleaner

· Check throttle, Connect spark plug wire.

Clean or replace air filter. Or contact a

qualified service person.

Engine is locked, will not pull

over. · Debris locked in impeller. Engine

problem. · See page 10. Contact a engine service

dealer for engine problems

Nozzle scrapes ground in

lowest height setting. Nozzle height out of adjustment Adjust nozzle height (See Nozzle height

fine adjustment for hard surfaces on

page 10

IMPELLER REMOVAL

1. Wait for engine to cool and disconnect spark plug.

2. Drain fuel and oil from engine.

3. Remove bag and remove upper handle.

4. Invert and support machine without engine touching to prevent damage to recoil starter.

5. Remove rear wheels (item 7), and bolt axle bracket (item 48), [one each side, closest to middle inlet

plate (item 3)], washer (item 57) and nut (item 49).

6. Remove intake wrapper (item 2), assembly and middle inlet plate (item 3), eight screws and eight nuts.

7. Remove impeller bolt (item 37) and lock washer (item 36).

8. Lift impeller free of engine.

9. If impeller does not remove easily, obtain a 1" (25.4mm) longer bolt of the same diameter and thread

type as the impeller bolt. Thread longer bolt by hand into crankshaft until bolt bottoms. Using a suitable

gear or wheel puller against the bolt head and impeller back-plate (near the blades), remove impeller from

shaft.

10. Reinstall new impeller, impeller bolt and lock washer in reverse order. Torque impeller bolt to 33-38

ft-lbs (45-52 N.m).

Part No 901014 Form No F072111C

LB Owner’s Manual

PARTS DRAWING LB

Part No 901014 Form No F072111C

LB Owner’s Manual

PARTS LIST

ITEM LB612 LB351

NO. Part No. Part No.

1 HOUSING ASSY 900590-04 1 900590-04 1

2 WRA PPER-INTAKE A SSY 900607-04 1 900607-04 1

3 PLATEMIDDLEINLET 900418 1 900418 1

4 PLATEWRAPPER 900413 2 900413 2

5 HANDLELOWER 900483 2 900483 2

6 PLATEBACKUP 900484 2 900484 2

7 WHEEL REAR 10" 900817 2 900817 2

8 AXLESHAFT 900818 1 900818 1

9 NUT LOCK 1/2 -13 THINHT. 8161044 2 8161044 2

10 BAG DEBRIS 900719 1 900719 1

11 WHEEL FRONT 8" 900816 2 900816 2

12 SPACER 900384 2 900384 2

13 PLATE- HT ADJ. 900414 2 900414 2

14 AXLEARM- HT. ADJ. 900416 2 900416 2

15 ARM ASSY - HT ADJ. 900417 2 900417 2

16 TIP-HT. ADJ. 900459 2 900459 2

17 SCREWCAP3/8-16 X 2 1/2" 8041056 2 8041056 2

18 HANDLE- UPPERASSY 900777 1 900777 1

19 HT. ADJ. ASSY 900820 2 900820 2

20 SPACER FRONT WHEEL 900819 2 900819 2

21 PLUG 900146-01 1 900146-01 1

22 ENGINE6.0 H.P. BRIGGS 890622 1 - -

ENGINEBRIGGS 500 SERIES - - 901012 1

23 LABEL EAR/EYEBREATHING 890254 1 890254 1

24 LABEL LOGO SMALL FRAME 441152 1 441152 1

25 WASHER 1/4 SAE 8172007 13 8172007 13

26 SCREWCAP5/16-16 X 1 1/4 8041029 1 8041029 1

30 WASHER 1/2" FLAT KD WHEEL MTG 900230 4 900230 4

32 KNOB-FOLDING HANDLE 900456 2 900456 2

33 IMPELLERASSY 900421 1 900421 1

35 KEY-3/16 SQ. X 1 1/4" 9201080 1 9201080 1

36 WASHER LOCK 3/8 S/T MED 8177012 1 - -

WASHER LOCK 7/16 S/T MED - - 8177013 1

37 SCREWCAP3/8-24 X 1" GR. 8 TORQUE33-38 FT. LBS (45-52.N.m.) 900154 1 - -

SCREWCAP7/16-20 X 1" HCS GR. 8 W/PATCH - - 510213 1

38 BAG LOOP 800178 2 800178 2

39 SCREW CAP1/4-20 X 1 1/4" 8041007 2 8041007 2

41 BOLT CARRIAGE5/16-18x2 1/4" 900466 2 900466 2

43 NUT LOCK 1/4 - 20 HEX ZP 8160001 5 8160001 5

44 SCREWCAP1/4 -20 X 1" 8041006 2 8041006 2

45 SCREWCAP1/4-20 X 3/4" 8041004 13 8041004 13

46 NUT LOCK WASHER 1/4-20 900453 10 900453 10

48 SCREWCAP5/16-18 X 1 1/4" 8041029 4 8041029 4

49 NUT LOCK 5/16-18 HEX ZP 8160002 3 8160002 3

50 WASHER FLAT 1/2 SAE(17/32 X 1 1/16 X 3/32) 8172011 4 8172011 4

52 SCREWCAP3/8-16 X 1 1/2" 8041052 2 8041052 2

53 WASHER LOCK 3/8 S/T MED 8177012 2 8177012 2

55 WASHER FLAT 3/8 SAE(13/32 X 13/16/ X 1/16) 8172009 2 8172009 2

56 SCREW CAP5/16-18 X 1 1/4 8041030 3 8041030 3

57 WASHER 5/16 SAE(11/32 X 11/16 X 1/16) 8172008 2 8172008 2

61 NUT LOCK 5/16-18 8160002 5 8160002 5

62 NUT LOCK 1/4-20 8160001 2 8160001 2

64 BRACKET AXLE 900487 2 900487 2

65 SPACER1/2 X 5/8 900231 2 900231 2

67 LABEL DANGER KEEP HANDS AND FEET AWAY 400424 2 400424 2

71 SCREW SELF-TAPPING 10-24 X 1/2 8123086 1 8123086 1

72 WASHER 5/16 FLAT CUT 8171003 3 8171003 3

73 LABEL FLYING DEBRIS 810736 1 810736 1

76 LABEL READ MANUAL 430363 1 430363 1

80 LABEL MADEINU.S.A. 520116 1 520116 1

DESCRIPTION QTY QTY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Billy Goat Rasen- und Gartengeräte Handbücher

Billy Goat

Billy Goat KD505SPQ Montageanleitung

Billy Goat

Billy Goat HTR1602V Montageanleitung

Billy Goat

Billy Goat KVSP Bedienungsanleitung

Billy Goat

Billy Goat DL2500SMM Bedienungsanleitung

Billy Goat

Billy Goat GZ401H Montageanleitung

Billy Goat

Billy Goat CR550HC Montageanleitung

Billy Goat

Billy Goat SC18OH Bedienungsanleitung

Billy Goat

Billy Goat CR550HC Bedienungsanleitung

Billy Goat

Billy Goat HTR1803V Montageanleitung

Billy Goat

Billy Goat AE1300HEU Bedienungsanleitung

Billy Goat

Billy Goat SC181H Bedienungsanleitung

Billy Goat

Billy Goat QV550HSP Bedienungsanleitung

Billy Goat

Billy Goat AE401V Bedienungsanleitung

Billy Goat

Billy Goat AEH Series Bedienungsanleitung

Billy Goat

Billy Goat SC121H Kurzanleitung

Billy Goat

Billy Goat F012507A Bedienungsanleitung

Billy Goat

Billy Goat DL1201L Bedienungsanleitung

Billy Goat

Billy Goat KD502SPQ Montageanleitung

Billy Goat

Billy Goat SC181H Bedienungsanleitung

Billy Goat

Billy Goat F042508A Bedienungsanleitung

Billy Goat

Billy Goat QL2000VE Montageanleitung

Billy Goat

Billy Goat PL1801H Bedienungsanleitung

Billy Goat

Billy Goat SC181HEU Bedienungsanleitung

Billy Goat

Billy Goat HTR1803VEU Montageanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung