Binary B-120-HDMATRIX-8x8 Bedienungsanleitung

Source | Mute | 2ch

(HDMI Out Audio)

INSTALLATION

MANUAL

HDMI MATRIX SWITCHER

B-120-HDMATRIX-8x8

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of re or electric shock, read and follow all instructions and warnings in this manual. Keep this

manual for future reference.

1. Do not expose this apparatus to rain or moisture. Do not expose this equipment to dripping or splashing, and

ensure that no objects lled with liquids, such as vases, are placed on the equipment. Do not use this apparatus

near water.

2. Do not remove cover. No user serviceable parts inside.

3. Clean only with a dry cloth.

4. Do not block any ventilation openings. Install according to manufacturer’s instructions.

5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including

ampliers) that produce heat.

6. Do not override the safety purpose of the polarized or grounding plug. A polarized plug has two blades, one

of which is wider than the other. A grounding plug has two matching blades and a third grounding prong. The

wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet,

consult an electrician for replacement of the obsolete outlet.

7. Protect the power cord from being walked on or pinched, particularly at the plug end and where the power

cord is attached to the apparatus.

8. Only use attachments and accessories specied by the manufacturer.

9. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged

in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled on or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, the apparatus does not operate

normally, or it has been dropped.

10. To completely disconnect this equipment from power, disconnect the power supply cord from the power

outlet.

LEGAL NOTICE

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK.

DO NOT REMOVE COVER. NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CONTENTS

1. Product Overview ................................................................................................................................................................................................. 4

2. Features ..................................................................................................................................................................................................................... 4

3. Package Contents................................................................................................................................................................................................... 4

4. Recommended for Installation.......................................................................................................................................................................... 5

5. Device Layout........................................................................................................................................................................................................... 5

5.1. Front Panel of the B-120-HDMATRIX-8x8 Switcher .................................................................................................................. 5

5.2. Rear Panel of the B-120-HDMATRIX-8x8 Switcher.................................................................................................................... 6

6. Installation & Setup................................................................................................................................................................................................ 6

6.1. Basic Installation Diagram ..................................................................................................................................................................... 6

6.2. Basic Instructions....................................................................................................................................................................................... 7

6.3. Installation Tips........................................................................................................................................................................................... 7

6.4. Switcher Location and Placement ....................................................................................................................................................... 8

6.4.1. Rack Installation ............................................................................................................................................................................. 8

6.5. HDMI Input Connections........................................................................................................................................................................ 8

6.6. HDMI Outputs............................................................................................................................................................................................. 8

6.7. Matrix Control Connections.................................................................................................................................................................. 8

6.7.1. RS-232 Control ............................................................................................................................................................................... 9

6.7.2. Ethernet/IP Control ...................................................................................................................................................................... 9

6.8. Matrix Switcher IR Connections ......................................................................................................................................................... 9

6.8.1. Matrix Switcher IR Port Conguration ................................................................................................................................. 9

7. EDID Conguration............................................................................................................................................................................................... 10

7.1. Source Setup ................................................................................................................................................................................................ 10

7.2. Display Setup ............................................................................................................................................................................................... 10

7.3. Auto EDID Conguration........................................................................................................................................................................ 10

7.3.1. How to Congure Auto EDID.................................................................................................................................................... 11

7.4. Embedded EDID Conguration............................................................................................................................................................ 11

7.4.1. Embedded EDID Chart ................................................................................................................................................................ 11

7.4.2. How to Set Embedded EDID for a Single Input................................................................................................................. 12

7.4.3. How to Set Embedded EDID for All Inputs.......................................................................................................................... 12

7.5. EDID Learning.............................................................................................................................................................................................. 12

7.5.1. How to Learn EDID to a Single Input...................................................................................................................................... 12

7.5.2. How to Learn EDID to All Input................................................................................................................................................ 12

7.6. Viewing Input EDID Status..................................................................................................................................................................... 13

8. Advanced Setup Using the Conguration Utility....................................................................................................................................... 13

8.1. IR Front Panel IR Enable.......................................................................................................................................................................... 13

8.2. Matrix Control from Room Enable...................................................................................................................................................... 13

8.3. Front Panel Power Button Active ........................................................................................................................................................ 14

9. Firmware Update.................................................................................................................................................................................................... 14

10. Operation and Control ...................................................................................................................................................................................... 14

10.1. IR Remote ................................................................................................................................................................................................... 14

10.1.1. Route Inputs to Outputs........................................................................................................................................................... 15

10.1.2. Turn Off (Mute) Outputs .......................................................................................................................................................... 15

10.1.3. Display Output Status ............................................................................................................................................................... 15

10.1.4. Resetting to Factory Defaults ................................................................................................................................................ 16

11. Troubleshooting ................................................................................................................................................................................................... 16

11.1. General Troubleshooting Guidelines............................................................................................................................................... 16

11.2. No Signal from Source to Any Display............................................................................................................................................. 16

11.3. No Signal from any Source to any Display ..................................................................................................................................... 17

11.4. Audio Issues............................................................................................................................................................................................... 17

12. System Layout Chart ......................................................................................................................................................................................... 18

13. Specications......................................................................................................................................................................................................... 19

14. Contacting Tech Support .................................................................................................................................................................................. 20

15. Warranty ................................................................................................................................................................................................................. 20

1. PRODUCT OVERVIEW

Welcome to Binary™. This product is engineered to provide years of exceptional reliability. We appreciate your

business, and we stand committed to providing our customers with the highest degree of quality and service in

the industry.

The B-120-HDMATRIX-8x8 is a state-of-the-art HDMI matrix switcher with HDMI outputs. It provides true matrix

routing for HDMI signals. With features such as HDMI 3D support, sophisticated EDID handling, and IR, RS-232

and Ethernet control, this product is ideal for residential and commercial media distribution systems.

Note: This manual covers installation and setup of the B-120-HDMATRIX-8x8 for most applications. Some

features must be congured using the Conguration Utility software. Go to the product page for the B-120-

HDMATRIX-8x8 at www.SnapAV.com and click on the Support tab to download the Conguration Utility and

manual.

2. FEATURES

• 8 HDMI inputs by 8 HDMI outputs

• Supports video resolutions up to1080p/60 36bit color

• Supports all HDMI audio formats

• Supports all HDMI 3D formats

• Sophisticated EDID handling including embedded, learned, and auto modes

• HDMI or DVI with adapter (not included)

• IR Control from integrated receiver or 3.5mm input

• Home Control via IR, RS-232 and Ethernet

• PC Setup and conguration using dedicated software

• HDCP 2.0 compliant

• CEC Passthrough

3. PACKAGE CONTENTS

• 1x B-120-HDMATRIX-8x8

• 2x rack ears for mounting

• 8x screws

• 1x IR remote control

• 1x Power supply 12VDC, 5A

• 1x Installation Manual

• 1x CD-ROM

4. RECOMMENDED FOR INSTALLATION

• Phillips screwdriver (for rack ear attachment)

• Binary high-speed HDMI cables to connect sources to B-120-HDMATRIX-8x8 HDMI inputs

• Control system to control operation of B-120-HDMATRIX-8x8

• Windows PC with Conguration Utility installed and RS-232 adapter

• Conguration Utility Manual

5. DEVICE LAYOUT

FIGURE 1: B-120-HDMATRIX-8x8 Switcher Layout (Front View)

5.1. Front Panel of the B-120-HDMATRIX-8x8 Switcher

A. Power On/Off Switch

Lights up blue when power is on and lights up red when in stand-by. Can be disabled from conguration utility

software

B. Source Status LEDs

Indicates that the selected source is On and transmitting an HDMI signal

C. Output Display

Displays the last output selected

D. IR Receiver Window

IR receiver for matrix to capture commands sent by IR remote

E. Input Display

Displays the last input selected

A EDCB

5.2. Rear Panel of the B-120-HDMATRIX-8x8 Switcher

FIGURE 2: B-120-HDMATRIX-8x8 Switcher Layout (Rear View)

A. Power Jack

+12V DC, 5A power supply connection

B. System IR In

To connect a control system with 3.5mm mono IR input for matrix control

C. RS-232 control port (DB9)

To communicate with control system or Windows PC for serial control of matrix

D. Ethernet Port

RJ45 port for connecting an ethernet Cat5e/6 cable for IP control of the B-120-HDMATRIX-8x8

E. HDMI Inputs (1 through 8)

Connect HDMI cables from sources to the matrix switcher for distribution

F. HDMI Outputs - (1 through 8)

Connect HDMI cables from matrix switcher to displays.

6. INSTALLATION & SETUP

6.1. Basic Installation Diagram

Complete the basic installation section to set up the matrix switcher for media distribution before completing any other

setup. Use this diagram for reference during basic installation of the matrix switcher, sources, displays, and wiring.

FIGURE 3: B-120-HDMATRIX-8x8 Installation

Control System

AC Power

Projector TV

Blu-ray Player

Cable/Sat Box

PC Game Console

HDMI

HDMI HDMI

RS-232

ACB

FD E

6.2. Basic Instructions

These are basic steps that must be taken to connect equipment to the inputs and outputs of the matrix switcher

and congure the system for use. See the sections listed for full information on completing each step.

1. Unpack the matrix and install it near the source equipment. (6.4. Switcher Location and Placement, page 8).

Note: Do not power the matrix switcher until it is indicated to do so.

2. Install and connect each source to an input on the matrix switcher using the shortest HDMI cable possible.

(6.5. HDMI Input Connections, page 9).

3. Install the displays and output wiring to the matrix location using HDMI cables for standard HDMI output.

4. Record the inputs and outputs used in the System Layout Chart for future reference. (13. System Layout Chart,

page 26).

5. If using a control system, connect it to the appropriate port on the matrix switcher for the driver type being

used: IR, RS-232, or IP control. (6.7. Matrix Control Connections, page 11).

6. Install and congure the driver for matrix switching control into the control system processor. (6.7. Matrix

Control Connections, page 11).

7. Install the IR equipment and set up IR passthrough if using it. (6.8. IR Passthrough Installation and Setup,

page 11).

8. Attach the power supplies to the matrix, sources, and displays to power up the system.

9. Test all input and output selections for sync, reliable switching, correct audio format and video resolution. Use the

factory remote or the Matrix Conguration Utility to set up EDIDs as needed. (7. EDID Conguration, page 16).

10. Change any advanced settings in the Matrix Conguration Utility as needed to suit the installation. (8.

Advanced Setup Using the Conguration Utility, page 19).

6.3. Installation Tips

Following these tips during the installation process will help guarantee a successful installation.

• Label each cable as it is installed.

This will aid in connection setup and programming, and will also make it easier to come back to a job at a later

date and immediately know what is connected where.

• Complete the System Layout Chart (page 25) in the back of the manual during installation.

Record the source connected to each input, the output number of each display, and the method of routing

signal in the chart for reference during installation and setup. Use it afterward to keep track of equipment in

use, open ports for expansion, and to help identify where to troubleshoot issues if they arise later.

• Leave an RS-232 connection easily accessible for using the Conguration Utility.

The B-120-HDMATRIX-8x8 is equipped with many setup functions that must be accessed by using a PC

and the Conguration Utility. Leave an RS-232 cable connected during setup and testing that can easily be

connected to the PC. If the matrix is being controlled by RS-232, disconnect the control system while using the

Utility.

• Do not fully secure wiring and equipment until setup and testing has been successfully completed.

Wait until all programming, sources, and zones have been set up and thoroughly tested to strap wiring and

equipment down, in order to avoid restricting access to connections and settings on the equipment.

• Complete initial setup with all sources connected to the matrix locally.

If a source will be connected to an input by an HDMI extender, complete initial setup by connecting directly to

the input with a short HDMI cable. Relocate the source and install the extender after the source has been set

up and tested, and then conrm the new arrangement works.

6.4. Switcher Location and Placement

Binary matrix switchers are designed to deliver unsurpassed technology with superior performance. However,

where you install the switcher could greatly affect the performance of the system, and the life of the unit. Here are

some guidelines to follow when installing a B-120-HDMATRIX-8x8 switcher.

• Be sure that the unit is in a well-ventilated area that provides adequate cooling.

• Do not block the cooling vents located on both sides of the unit.

• Do not place the unit on carpeting or any similar material.

• Do not install the unit near a source of heat, or in an extremely humid or wet location.

• If your enclosure lacks good air ow (such as solid cabinet doors or wall-mounted racks), it may be necessary to

create ventilation to allow outside air into the space.

• Allow a minimum of 3" of free air space on either side of the unit. (Does not apply to rack mounting).

• Allow a minimum of 2" of depth behind unit to accommodate cables and connectors.

• When placing on a cabinet shelf, position the unit with all feet resting on a solid level surface.

6.4.1. Rack Installation

The B-120-HDMATRIX-8x8 can be mounted in a rack with the front or rear panel facing outward, and will

displace 1U of vertical space when installed. Rear-facing installation allows for easy access to the connections

for installations that do not require the front panel of the unit to be accessed. Front-facing mounting is useful for

applications where the front panel must be accessible or visible.

The rack ears are packaged separately from the matrix switcher in the box. Attach the ears to the sides of the

matrix at the front or back using the included screws. Tighten with a #2 Phillips Screwdriver. It may be necessary to

remove the feet from the bottom when rack mounting the matrix switcher. Remove the screws for the feet with a

#2 Phillips Screwdriver and store the feet and screws together in case they are needed in the future.

Note: The rack ears and mounting holes are only designed to safely hold the weight of the B-120-HDMATRIX-8x8.

CAUTION: Do not use the matrix switcher as a shelf for other equipment in the rack.

6.5. HDMI Input Connections

Each of the eight inputs on the B-120-HDMATRIX-8x8 utilize a standard HDMI port for connection. Follow these

guidelines when connecting sources to the inputs.

• Always use the shortest cable possible between source equipment and the matrix switcher inputs. Use

high-speed rated cables to guarantee the best possible performance.

• Always run one continuous cable when possible and avoid using HDMI cable adapters in runs.

6.6. HDMI Outputs

The HDMI outputs of the matrix can be connected to the input of a sink device (TV, AV receiver, ber extender,

etc.). Please follow the guidelines below to ensure best performance and reliability.

• Always use the shortest, possible cable between equipment. Use high-speed rated cables to guarantee the best

possible performance.

• Always run continuous HDMI cables and avoid using HDMI cable adapters.

• When routing HDMI to an AV receiver, make sure to set the AV receiver to an HDMI mode where the signal

will not be processed or scaled to a different format. This will avoid signal timing issues that can cause

intermittent sync or total loss of sync. Contact the device manufacturer for details regarding HDMI setup.

6.7. Matrix Control Connections

All drivers, associated software and extra documentation is available under the Support tab on the

B-120-HDMATRIX-8x8 product page at www.SnapAV.com.

Note: System IR control and the front panel IR receiver can be disabled when not in use by using the Conguration

Utility. See the Conguration Utility Manual section, Other Settings for more information.

6.7.1. RS-232 Control

To control the B-120-HDMATRIX-8x8 with RS-232, the devices must connect using the correct pin conguration

for the control system in use.

The matrix switcher receives control data on pin 2 (RxD – Data Receive) and transmits control data on pin 3

(TxD-Data Transmit). See the diagram below for details.

Conguration for control system serial ports can vary. Refer to the documentation for the system in use to ensure

proper connection and conguration.

Note: This port is also used to communicate with a PC when using the PC Conguration Utility. Refer to the

Conguration Utility Manual for details.

Pin Function

2 RxD (Data Receive)

3 TxD (Data Transmit)

5 Ground/Common

FIGURE 4: RS-232 (DB9) Pin Congurations

6.7.2. Ethernet/IP Control

The B-120-HDMATRIX-8x8 includes an Ethernet port that can be used to control the device using Telnet Protocol.

This port follows TIA 568B standards; please refer to these standards when terminating cables.

To congure the matrix switcher for use with the driver, it will be necessary to connect the unit to a PC and access

it with the Matrix Conguration Utility. See the Conguration Utility Manual and the IP driver documentation for

complete setup instructions.

6.8. Matrix Switcher IR Connections

FIGURE 5: IR Connections

A. System IR In (3.5mm mono)

IR input port for matrix switcher IR control.

6.8.1. Matrix Switcher IR Port Conguration

The System IR In on the B-120-HDMATRIX-8x8 is 3.5mm mono and only uses this pinout conguration.

Matrix IR

Control Input IR Signal (Tip)

GND (Sleeve)

FIGURE 6: IR Port Conguration

Consult with the manufacturer of any attached IR equipment to conrm their pinout matches before use. Visit our

website for HEX codes under the support tab of this product’s page.

DB9 Female Connector

RxD (Data Receiver

TxD (Data Transmit)

GND

AB-120-HDMATRIX-8x8

7. EDID CONFIGURATION

The displays used within an installation usually vary from room to room, and some may not support all resolutions

available from a source. It is necessary to make sure sources will provide a video and audio format compatible with

all connected displays programmed to use them. To accomplish this, the B-120-HDMATRIX-8x8 includes built-in

EDID management for each source input. The stored EDID is per source, so all display locations will see the same

resolution and have the same audio format when that source is selected.

Note: Source is only able to output one video resolution and one audio format.

Note: The default EDID for each input is always 1080p with 2-channel stereo audio, since this format is accepted

by most displays with no issues.

The following sections explain conguring EDIDs via the included IR remote. Before conguring the EDID, be

sure to refer to the source and display manuals for available features and resolutions for each device. For more

information about using the included remote, see Section 10.1 IR Remote on page 21.

While all EDID congurations are available via the remote, the Conguration Utility can be used for faster setup.

Download the Conguration Utility and manual on the Support tab at the product page for the

B-120-HDMATRIX-8x8 at www.SnapAV.com.

What is EDID? EDID, or Extended Display Identication Data, is a stream of information sent from a display to a

source when the two devices are connected to tell the source what video and audio formats the display can use.

This prevents sources from outputting media that won’t work with the display.

7.1. Source Setup

Check each source and conrm that the audio format and video resolution are set so that they will change based

on the EDID. Normally this setting is called Auto or similar.

Note: EDID setup is not required if the source supports setting one xed video resolution and audio format.

7.2. Display Setup

It is recommended that Consumer Electronics Control (CEC) be turned OFF in all displays when using the

B-120-HDMATRIX-8x8. This will provide for proper communication of video/audio signals and allow EDIDs to

function at their optimum performance. Refer to the display’s manual for information on how to turn this function

OFF.

7.3. Auto EDID Conguration

The quickest and easiest method for conguration is to use Auto EDID. When this mode is used the matrix

switcher looks at the EDID from each of the connected displays. It uses the highest common video resolution to

create a new EDID and saves that EDID in all of the inputs.

Note: Auto EDID sets audio to 2-channel stereo for all inputs regardless of the capability of the connected displays.

If multi-channel audio is desired, embedded EDIDs or Learned EDIDs will need to be used.

When to use Auto EDID

• All sources will be available on all displays.

• As a rst step to conguration following up with advanced methods for particular displays and dedicated sources.

• For advanced EDID conguration when using a legacy display and/or dedicated sources, use embedded EDIDs

or learning as described in the following sections.

Inhaltsverzeichnis

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung