BIXOLON SPP-R220 Gebrauchsanweisung
WLAN Connection Manual
SPP-R220
Mobile Printer
Rev. 1.00
http://www.bixolon.com
Rev. 1.00
- 2 -
SPP-R220
■Table of Contents
1. Manual Information........................................................................................................3
2. Precautions ....................................................................................................................3
3. How to Connect..............................................................................................................4
3-1 Android Soft AP mode................................................................................................6
3-2 iOS Soft AP mode.......................................................................................................7
3-3 How to change infrastructure mode............................................................................8
4. Factory Reset...............................................................................................................10
Rev. 1.00
- 3 -
SPP-R220
1. Manual Information
This WLAN manual provides information on the connection of wireless network with the
mobile printer.
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and
quality of all our products. In following, product specifications and/or user manual content
may be changed without prior notice.
2. Precautions
2-1 The printer has to be within 100m(Out door) from AP(Access point) to connect
WLAN. Although 35m is able to communicate in door, WLAN could be affected by
environment to be shorten.
The STATUS LED on the printer indicates the signal strength of the wireless LAN.
When the green LED is on, the wireless LAN signal strength is good. When the green
LED is blinking, the signal is weak. If the STATUS LED is off, it indicates that there is
no signal from the AP, and the red LED is lit if the security option or key is incorrect.
2-2 The maximum separating distance may be shortened if transmission obstacles, such
as cement walls, are present
2-3 If a device (such as a microwave oven, wireless LAN, etc.) that uses the same
frequency is present, transmission may be interrupted. Separate the printer and
Bluetooth-enabled device from such interrupting devices by a distance of at least 5m.
Rev. 1.00
- 4 -
SPP-R220
3. How to Connect
WLAN can be configured through the printer’s WLAN interface. Likewise, WLAN can also
be configured though the printer’s USB interface.
(1) Connecting Printer
1) USB cable
Connect USB cable to Printer, PC device.
2) WLAN
Connect to the AP (Access Point) configured in Infrastructure mode in order to connect
to the LAN/wireless network
<Infrastructure mode>
In order to configure the network between the wireless host device and the printer, set the
printer to Soft AP Mode.
<Soft AP mode>
A P
Rev. 1.00
- 5 -
SPP-R220
(2) Checking Network Setting
Self-test
While the printer is turned off, turn on the printer while pressing the feed button.
The printer setting values will then be printed.
Power
FEED
Rev. 1.00
- 6 -
SPP-R220
3-1 Android Soft AP mode
1) Select “Wi-Fi”. 2) Select the printer to connect.
3) Select “CONNECT”. 4) Wi-Fi communication is available.
Rev. 1.00
- 7 -
SPP-R220
3-2 iOS Soft AP mode
1) Select “Wi-Fi”. 2) Wi-Fi ON and Select the printer to connect.
3) Wi-Fi communication is available.
Rev. 1.00
- 8 -
SPP-R220
3-3 How to change infrastructure mode
1) Enter the IP address of the printer in the address bar, and the following login window will
pop up. Enter the ID and Password set for the printer, and then click [LOG IN]
(Default User Name: admin, Password: password)
2) Select “Wireless” to change WLAN Connection Type.
Rev. 1.00
- 9 -
SPP-R220
3) Select “Infrastructure”, and set SSID, WLAN Security Type.
4) Reboot the Printer.
Rev. 1.00
- 10 -
SPP-R220
4. Factory Reset
This function changes the WLAN settings of the printer to the initial factory settings.
Method
To set Factory reset mode, printer should be in Hexa Dump mode.
1) Hex dump mode
After turning off the power, open the cover.
Turn on the printer while holding down the feed button like self test mode.
Then close the cover to enter hexa dump mode. The below message is printed.
Hexadecimal Dump
To change WLAN setting values factory default
Press POWER button three times!!
To terminate hexadecimal dump
Press FEED button three times!!
Push the Power button 3tiems, WLAN setting will be reset as a factory default and below
message is printed.
*** WLAN Factory Reset Completed! ***
*** Please Reboot Printer ***
< Online Hex Dump Completed >
After turning off the printer and on, WLAN setting will be factory default.
Power
FEED
Andere Handbücher für SPP-R220
2
Inhaltsverzeichnis
Andere BIXOLON Drucker Handbücher
BIXOLON
BIXOLON SRP-380 Installations- und Betriebsanleitung
BIXOLON
BIXOLON SRP-350plusIII SRP-352plusIII Bedienungsanleitung
BIXOLON
BIXOLON XT5-40NR Series Bedienungsanleitung
BIXOLON
BIXOLON SRP-350plusIII SRP-352plusIII Montageanleitung
BIXOLON
BIXOLON SRP-Q200 Bedienungsanleitung
BIXOLON
BIXOLON SRP-350plusII Bedienungsanleitung
BIXOLON
BIXOLON XD5-40d Series Bedienungsanleitung
BIXOLON
BIXOLON SPP-R220 Bedienungsanleitung
BIXOLON
BIXOLON SRP-330II Bedienungsanleitung
BIXOLON
BIXOLON SRP-275II Bedienungsanleitung
BIXOLON
BIXOLON SLP-DX420B Bedienungsanleitung
BIXOLON
BIXOLON SRP-F310 Bedienungsanleitung
BIXOLON
BIXOLON SPR-350III Installations- und Betriebsanleitung
BIXOLON
BIXOLON Bixolon SRP-270 Bedienungsanleitung
BIXOLON
BIXOLON SRP-380II Bedienungsanleitung
BIXOLON
BIXOLON SRP-350plusIII SRP-352plusIII Bedienungsanleitung
BIXOLON
BIXOLON SRP-F310 Bedienungsanleitung
BIXOLON
BIXOLON SRP-F310 Montageanleitung
BIXOLON
BIXOLON SRP-350plusV Gebrauchsanweisung
BIXOLON
BIXOLON SRP-350IIOBEi Bedienungsanleitung
