BKT Elektronik BPS2000v2 Bedienungsanleitung

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

a

Instrucons

S2000v2 Mo

Operang Instrucons

BPS2000v2 Monitoring Power Distribuon

Ver.01.22

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

Table of contents

1. Safety precauons

......................................................................................................................................3

2. Foreword

.....................................................................................................................................................3

3. Package contents

….....................................................................................................................................3

4. Applicaon of BPS2000 unit

.......................................................................................................................3

5. Installaon of BPS2000 unit

……………….......................................................................................................4

6. Unit BPS2000 general characteriscs ……….………….……..............................................................................5

6.1 View of the control module, including a descripon of the connectors ………................................6

6.2 LCD display interface for 250V single phase version ….…................................................................7

6.3 LCD display interface for 400V three phase version ….…................................................................8

7. Managing the BPS2000 unit .

…………………………..………………………………………………………………………….....….10

7.1 Access through web browser …...…….............................................................................................10

8. Seng the unit BPS2000 to the factory conﬁguraon

…………..................................................................17

9. Access via Telnet protocol

………………........................................................................................................18

10. Access via SNMP protocol

……………..…………............................................................................................24

10.1 OID table..……...............................................................................................................................25

11. Access via ModBus TCP protocol

……………...….........................................................................................32

12. Access via ModBus RTU protocol..

..........................................................................................................33

12.1 Modbus RTU/TCP memory map...................................................................................................35

13. Technical parameters of BPS2000 unit

………………………………………………….………………………………..……….40

13.1 Control module speciﬁcaon …..…….…………………..……………………………………………………...…………41

13.2 Addional accessories ……….…………….…………………………………...…………………………………...…………41

14. Warranty .

……………………………….………………………………………………………………….………………………….………..42

15. BPS2000 unit soware update

……………………..…………………………………………………….……….…….…......…....46

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

1. Safety precauons

• The unit must only be installed by qualiﬁed personnel in accordance with the following installaon and

operang instrucons.

• The manufacturer is not liable for incorrect use of the device, in parcular use of the device that could

lead to health injury or material damage.

• The device should not be opened or disassembled when it is live.

• The device may only be connected to a 230V AC power outlet (50Hz or 60Hz) for the single-phase ver-

sion and 380-400V (50Hz/60Hz) for the three-phase version in star arrangement.

• Power cords, plugs and sockets should be in good technical condion. The device should always be con-

nected to a properly earthed socket.

• The device is intended for indoor use only. Do not install the device in locaons where excessive mois-

ture or high temperatures may occur.

• For safety and oﬃcial approval reasons, do not modify the device without prior authorizaon.

• Also, refer to the instrucons for use and safety instrucons for the connected devices.

• If aer reading the manual, you have any quesons regarding the installaon, operaon or use of the

device, please contact the customer service department.

2. Foreword

The BPS2000 monitoring power distribuon unit allows for power distribuon and monitoring of power

supply voltage, total current load, total acve, reacve and apparent power consumpon. In addion,

the unit has integrated power consumpon meters and enables measurement of power factor (cosφ).

The units are equipped with a new generaon replaceable control and measurement module with a built

-in LCD display working in “hot swappable” technology, which displays informaon about power supply

voltage, current load, acve power consumpon and energy consumpon.

Thanks to the applicaon of SNMP and ModBus RTU protocols, it is possible to fully integrate the

BPS2000 unit with external management soware.

3. Package contents

x BPS2000 series PDU

• Supply cord: 2M (RJ45/RJ45)

• Quick start instrucons

x Mounng brackets (111SA200014.3 )

4. Applicaon of BPS2000

The BPS2000 units are used in IT, ICT, Data Center and power distribuon environments. In addion, they

allow monitoring of electrical parameters at the power input of the PDU along with monitoring of environ-

mental condions in the server rack.

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

5. Installaon of BPS2000 unit

The BPS2000 units are designed for vercal installaon as shown in the ﬁgure below.

As a standard, the units can be mounted with ﬁxed brackets or brackets dedicated for 4DC and SRS/SSRS rack

cabinets.

PDU brackets for BKT 4DC racks of width 600/800 mm (set)

Index: 111SA200014.3

PDU brackets for BKT SRS/SSRS racks (ordered separately)

Index: 111SA200018.3

Example of mounng the unit in 4DC rack cabinet, mounng to the 19" proﬁle front and side view

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

6. BPS2000 general characteriscs

The BPS2000 monitoring device is a power distribuon device that allows monitoring electrical parame-

ters at the unit's input. It is equipped with a management module that allows supervision and control of

electrical parameters with access via a web browser. Units are available in single-phase and three-phase

designs with a load of 16A to 32A for each phase.

Units can be equipped with IEC320 C13, IEC 320 C19, NF C61-314 (st.PL/FR) or

DIN49440 (Schuko), also available with a disconnect lock for C13/C19 sockets.

Funconality:

Monitoring of electrical parameters at the PDU input:

• Unit power supply voltage [V]

• Total current load of the unit [A]

• Acve Power, Apparent Power, Reacve Power [kW, kVA, kVAR]

• Energy consumpon/counter of acve energy, apparent energy [kWh, kVAh]

• Power factor [PF] (cosɸ)

• Frequency [Hz]

Monitor environmental condions with dedicated sensors:

• temperature and humidity

• door opening, ﬂooding, smoke

The unit is equipped with an interchangeable management module made with technology

"Hot Swappable." Replacement of the module does not cause interrupon of power supply to the re-

ceivers. The web interface is available from any web browser in Polish and English.

Communicaon is carried out using built-in network and communicaon protocols:

• SNMPv1/v2c/v3, Modbus RTU, Modbus TCP/IP

• HTTP, SMTP, Telnet

• IPv4/IPv6

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

6.1. View of the control module with descripƟon of the connectors

x DescripƟon of connectors, controls and LED lights

1. Led lights:

RUN

: operang status of the control module

indicates correct status of the device - ﬂashing green LED (1:1)

kWh

: energy count pulse signaling

ALM

: alarm status

Normal state - LED oﬀ

Fault - LED blinking red (1:1)

2. Menu - main menu of control module

3. Up - moves to the next LCD screen

4. Down - returns to the previous LCD screen

5. Reset - control module restart

6. T/H - port for connecng temperature/humidity sensor

7. NET(RJ45) - Network port

Descripon of LED lights:

yellow/status - ON: port is connected, OFF: port is disconnected, blinking: data is transmied

green/rate - ON: 100Mbps, OFF: 10Mbps

8. SB - Sensor Box environmental condions module connecon port

9. OUT - serial communicaon output port RS485 (Modbus RTU/SNMP)

10. IN - serial communicaon input port RS485 (Modbus RTU/SNMP)

11. LCD screen

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

6.2 LCD display interface for 250V single phase version

Screen 1

Read: Phase(L1) / Load(0.0A) / Voltage(237.6V) / Acve power (0.0kW) / Energy(0.0kWh)

Screen 2

Read: Phase(L1) / Load(0.0A) / Voltage(237.6V) /Acve power (0.0kW)/Power factor (0.00)

Screen 3

Read: the IP address of the BPS2000

Screen 4

Read/Write*: Master/Slave conﬁguraon for SNMP or ModBus RTU

Address: 00 indicates that the unit is in master mode

Address: 01 ÷04 indicates that the unit is working in Slave mode from 1 to 4

Screen 5

Read/Write*: Seng of threshold values, maximum for the following parameters

Load(32A)/ Voltage(250.0V)/ Temperature(44°C)/ Humidity(99%).

32A

250 V

44 °C 99 %

Add

192

168 000

163

Press UPPress

Screen 1 Screen 2

Screen 5

Press

Screen 3 Screen 4

L1 0.00A

237.6V 0.0kW

000012.5kWh

L1 0.00A

237.6V 0.0kW

PF-0.00

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

6.3 LCD display interface for 400V three phase version

Screen 1

Read: Phase(L1) / Load(0.0A) / Voltage(237.6V) / Acve power(0.0kW)/ Energy(000000.kWh)

Screen 2

Read: Phase(L1) / Load(0.0A) / Voltage(237.6V) / Acve power(0.0kW)/ Power factor(0.00)

Screen 3

Read: Phase(L2) / Load(0.0A) / Voltage(235.5V) / Acve power(0.0kW)/ Energy(000000.0kWh)

Screen 4

Read: Phase(L2) / Load(0.0A) / Voltage(235.4V) / Acve power(0.0kW)/ Power factor(0.00)

Screen 5

Read: Phase(L3) / Load(0.0A) / Voltage(234.9V) / Acve power(0.0kW)/ Energy(000000.0kWh)

Screen 6

Read: Phase(L3) / Load(0.0A) / Voltage(235.0V) / Acve power(0.0kW)/ Power factor(0.00)

Screen 7

Read: the IP address of the BPS2000

Screen 8

Read/write*: Master/Slave conﬁguraon

Address: 00 indicates that the unit is in master mode

Address: 01-04 indicates that the unit is working in Slave mode from 1 to 4

Screen 9

Read/write*: Seng of threshold values, maximum

Phase(L1) / Load(16A) / Voltage(276.0V) / Temperature(40°C) / Humidity(99%)

Screen 10

Read/write*: Seng of threshold values, maximum

Phase(L2) / Load(16A) / Voltage(276.0V) / Temperature(40°C) / Humidity(99%)

Screen 11

Read/write*: Seng of threshold values, maximum

Phase(L3) / Load(16A) / Voltage(276.0V) / Temperature(40°C) / Humidity(99%)

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

6.3 LCD display interface for 400V three phase version

Press

Screen 1

L1 0.00A

237.6V 0.0kW

000012.5kWh

Screen 7

L3 0.00A

234.9V 0.0kW

000019.1kWh

Screen 6

Screen 2

L1 0.00A

237.6V 0.0kW

PF-0.00

Press

Screen 3

L2 0.00A

235.5V 0.0kW

000020.4kWh

Press

L3 0.00A

235.0V 0.0kW

PF-0.00

Screen 5

Press

192

168 0

163

Screen 4

Press

L2 0.00A

235.4V

0.0kW

PF-0.00

Screen 8

Add

Screen 9

16A

276

40°C 99%

Screen 10

16A

276

40°C 99%

Press

Screen 11

16A

276

40°C 99%

Press

Operang Instrucons - BPS2000v2 Monitoring Power Distribuon Unit

7. BPS2000 unit management

BPS2000 unit has a built-in web server for communicaon over the Ethernet. No addional soware is

required to communicate with the unit. The soware allows to manage the unit, conﬁgure alarms, ne-

twork sengs and remotely restart the device. The web interface has been wrien in Polish and

English.

7.1 Access through a web browser

1. The unit has a factory-set ﬁxed IP address: 192.168.0.163

2.Enter the IP address of unit BPS2000 into the browser and press Enter, the login

window will appear. T

The default username is admin with the password admin

3. Aer logging in, the web interface is available in two language versions (Polish and English).

Inhaltsverzeichnis

Andere BKT Elektronik IP-Zugriffskontrollsysteme Handbücher

BKT Elektronik

BKT Elektronik ACBS Handbuch

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

Jantar

Jantar REX A-1-9 Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

Software House

Software House iSTAR Pro 2U RM Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung