Black & Decker GR120 Bedienungsanleitung

English

GR120_UK.P65 09-11-2000, 14:271

RotaryLawnmower

GR120 User manual

Congratulations!

On your purchase of your Black & Decker rotary

lawnmower.

This user manual provides important operating and

maintenance instructions for all of the non grass

collecting rotary mowers in the Black & Decker

GR120 range.

Know your mower

Read all of this manual carefully, observing all

the recommended safety instructions before,

during and after using your mower, and

maintain your mower in good working order.

Familiarise yourself with the controls on

your mower before attempting to operate

it, but above all, be sure you know how to

stop your mower in an emergency.

Retain this user manual and all other literature

supplied with your mower for future reference.

Safety instructions

Training

•Never allow children or persons who

are unfamiliar with this type of mower to

use it, nor anyone who has not read

this user manual.

Do not allow children, animals

or other persons near your

mower when in use - always

keep them at least 6m (20ft)

away from the cutting area.

•Remember that the operator is

responsible for accidents or hazards

occurring to other people or their property.

•Your mower is designed for use on AC

(mains) electrical supplies only - do not

attempt to use it on any other supply.

•Plug your mower into a power point -

never a lighting socket.

•Never carry your mower by the cable or

jerk the cable to seperate the

connectors. Keep the cable away from

heat sources, oils or sharp edges.

Check the condition of your cable

before use and do not use if damaged.

Preparation

•To protect your feet, always wear stout

shoes or boots - freshly cut grass is

damp and slippery.

•Rubber or man-made footwear will

enhance your safety.

•Do not operate your mower barefoot or

in open sandals.

•Use protective equipment. Wear safety

spectacles or goggles whilst operating

your mower. Use ear protection if the

sound level seems uncomfortable when

using your mower.

•Use a face mask if dusty.

•Wear long trousers to protect your legs

- any debris left on the lawn or cutting

path may be picked up and ejected by

the blades.

•The power supply cable should be

regularly inspected for signs of damage or

ageing, and only used if in good condition.

•Always keep the power supply cable

away from the blades - be aware of its

position at all times.

•Always be sure your mower is in a safe

operating condition.

•Before using your mower, disconnect it

from the electrical supply and visually

check that the blade, blade nut and

cutter assembly are not worn or

damaged. A damaged blade or worn

blade nut is a major hazard and must

be replaced. Also check that the blade

nut is securely fastened.

•Always check that your lawn or cutting

path is clear of all sticks, stones, wire

and other debris. Contact with such

debris may be dangerous or may

damage your mower and could be

thrown by the blade.

Operation

•When tilting the handle downwards (or

to the side) to start your mower, do not

tilt it more than is absolutely necessary.

Always ensure that both hands are in

the operating position and feet are well

away from the blades before returning

your mower to the ground.

Your mower will continue to run

for a short time after releasing

the switch lever. Always allow

your mower to stop on its own.

•Release the switch lever to turn your

mower off and remove the plug from

the mains:

GR120_UK.P65 09-11-2000, 14:472

ENGLISH

•Do not use solvents or cleaning fluids to

clean your mower - use a blunt scraper

to remove grass and dirt.

•Always disconnect from the electrical

supply before cleaning.

•Do not operate your mower if any parts

are defective; discard all defective parts

and fit new parts before use.

•Keep all nuts, bolts and screws tight to

be sure your mower is in a safe working

condition.

•Use only Black & Decker recommended

replacement parts and accessories.

Black & Decker’s policy is one of continuous

improvement to our products and, as such, we

reserve the right to change product specifications

without prior notice.

Double insulation

Your mower is double insulated.

This means that all external metal parts are

electrically isolated from the power supply.

This is achieved by placing an extra

insulation barrier between the electrical and

mechanical parts. Double insulation means

greater electrical safety and obviates the

necessity of having your mower earthed.

Electrical safety (UK only)

Your mower should always be switched off

at the mains before disconnecting any plug

and socket connector or extension cables.

Fuse replacement

If your mower is supplied with cable fitted

with a non-re-wireable plug:

•The plug is fitted with a 5 amp fuse

which is the recommended fuse for

your mower.

•Only use replacement fuses which are

approved to BS1362.

•When changing the fuse in your plug,

always ensure the fuse cover is refitted.

If the fuse cover is missing or damaged

do not use the plug.

Note: Fuses do not give personal

protection against electric shock.

•Whenever you leave your mower

unattended.

•Before checking, cleaning, adjusting

or working on your mower.

•Before clearing a blockage.

•If your mower starts to vibrate

abnormally (check immediately).

•After striking a foreign object,

inspect your mower for damage and

make repairs as necessary.

•Never run your mower whilst lying on its

side or attempt to stop the blade -

always allow it to stop on its own.

•Do not put hands or feet near or under

rotating parts.

•Keep clear of discharge openings at all

times.

•Start your mower carefully according to

the instructions and with your feet well

away from the blade.

•Do not use your mower in the rain and

do not allow it to get wet. Avoid using

your mower in wet grass, if possible.

•Use your mower only in daylight or

good artificial light.

•Do not pull your mower towards you or

walk backwards when in operation.

•Do not cross gravel paths or roads

whilst the tines are rotating.

•Always be sure of your footing,

particularly on slopes.

•Always cut across the face of slopes,

never up and down. Exercise extreme

caution when changing direction on

slopes.

•Do not cut excessively steep slopes

and always wear non-slip footwear.

•Check the grassbag (if supplied) for

wear or damage and replace if

necessary. Never use your mower

without the grassbag in place.

•Walk, never run. Do not force your

mower.

•Never pick up or carry your mower

while the motor is running.

•Ensure the blade has stopped rotating

and take extreme care before lifting your

mower for and during transportation.

•Never operate your mower with

defective guards or shields.

Maintenance and storage

•Store your mower in a dry place when

not in use, out of the reach of children.

GR120_UK.P65 09-11-2000, 14:273

Plug replacement

•Disconnect the plug from the supply.

•Cut off the plug and dispose of

immediately. Insertion of a detatched

plug into a 5 amp socket outlet may

result in electric shock.

•Only fit BS1363A approved plugs fitted

with the correctly rated fuse.

•The cable wire colours, or a letter, will

be marked at the connection points of

most good quality plugs. Attach the

wires to their respective points in the

plug (see below). Brown is for “Live” (L)

and blue is for “Neutral” (N).

•Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

Warning! Never connect live or neutral

wires to the earth pin marked “E” or .

Note: Do not wire an extension cable directly

into your mower yourself. Instead, take your

mower to your nearest Black & Decker

service agent.

Increased safety can be obtained by having

a qualified electrician install a high

sensitivity (30mA) circuit breaker in the

house wiring.

If you do not have such a circuit breaker

installed, or you do not wish to have one

installed, then we strongly recommend that

the electrical power to your mower be

supplied through a high sensitivity residual

current device (RCD). The RCD is designed

to provide a high degree of personal

protection against harmful electric current

should fault conditions occur.

Warning! The use of an RCD or other

circuit breaker unit does not release the

operator of your mower from the safety

instructions and safe working practices

given in this manual.

Handle assembly (Fig. A - E)

ARemove all the parts from the carton and

familiarise yourself with the individual parts

of your mower.

The main parts of your mower are your

mower body (1) which houses the motor.

Attached to your mower body are the front

wheels (2) which incorporate adjustment

for the cutting height and the rear roller (3).

Pivot pins are built into your mower body to

accept the handle.

The handle comprises the lower handle

tube (20), the upper handle tube (21),

switch box (22) with switch lever (23) and

safety lock-off button (24), electrical supply

cable (11), the cable clips (12) and the

handle clamp assemblies (25), which each

comprise a wing nut, spacer and bolt.

Note: The electrical supply cable should be

positioned on the right hand side of your

mower when viewed from the operating

position. Ensure that this is not damaged

or twisted before you begin to assemble

your mower.

Assemble the lower handle tube (20) to

your mower body (1), as follows:

B•Compress the lower handle tube (20)

and fit oyour mower body (1).

With the lower handle tube (20) in position,

assemble the upper handle tube (21) to it,

as follows:

C•Place the upper handle tube (21) over

the lower handle tube (20), aligning the

holes in the upper handle tube (21) and

the lower handle tube (20).

•Fit a bolt (26) through each hole and fit

a wing nut (27), flat washer and lock

washer to the bolt (26). Tighten each

wing nut with firm pressure only.

Note: Do not use a spanner or other

implement to tighten the wing nuts.

•With the upper and lower handle tubes

assembled, fit the switch box (22) to

the upper handle tube (21), as follows:

Note: The switch box must be positioned

on the right-hand side of your mower.

Ensure that the electrical supply cable (11)

is not twisted.

E•Locate the two pins on the switch box

(22) with the holes in the upper handle

tube (21).

•Fit the retaining plate (28) over the

stem of the upper handle tube (21)

and secure in position using the screws

(29) provided.

GR120_UK.P65 09-11-2000, 14:274

ENGLISH

Note: Do not overtighten these screws -

light pressure will be sufficient to hold the

switch box in position.

•Finally, using the cable clips (12)

provided, secure the electrical supply

cable (11) to the upper and lower

handle tubes (20 and 21) (Fig. A).

Fitting a new blade (Fig. F & G)

Observe all the relevant warnings before

changing the blade.

Warning! Disconnect your mower from the

electrical supply before changing the blade.

F•The plastic blades are designed for

safer mowing and can be used to

maintain grass at the required length -

they are not designed for heavy cutting.

•Assembly of the blades (35) to the

blade carrier (38) is done by placing a

blade onto the metal rivet in direction of

arrow (A) and then pulling the blade in

direction of arrow (B) until it fully snaps

into position. Repeat for second blade.

G•Two cable clips are provided. You may

find assembly of the motor cable to

these clips easier if the cable is

attached to the clips first and then push

the clips onto the handle tubes.

Note: Some mowers are fitted with a

clutch washer, between the blade nut and

the blade, which must be re-assembled at

all times.

Height of cut adjustment (Fig. H)

HThere are three cutting height positions

on your mower.

These are selected by loosening the wing-

nuts (36) on the front wheels (2) (Fig. H),

moving the wheels to the required height

position and re-tightening the wing-nuts (36).

Note: The three cutting height settings are

indicated by raised mouldings on the

underside of your mower body (1). Indicator

plates (37), fitted to the rear of the bolts

which pass through each front wheel, are

provided as a guide to set the cutting height

i.e. aligning the pointer on the indicator plate

with the raised mouldings on the underside

of your mower body. Both wheels must be

set to the same height position to achieve a

good finish on your lawn.

The three cutting height positions are

as follows:

•Lowest setting. This is for use on dry

grass less than 38mm (11⁄2inches) in

height, on a flat lawn.

•Medium setting. This is for use on

damp grass or grass between 38 to

65mm

(11⁄2to 21⁄2inches) in height.

•Highest setting. This is for use on damp

grass more than 65mm (21⁄2inches) in

height, or where the lawn is not flat.

For grass more than 76mm (3 inches) high

(i.e. at the beginning of the season) use

your mower for short periods of time, then

allow the motor to run for 2 to 3 minutes

whilst your mower is stationary to allow it to

cool down. If the motor suddenly stops

during use, disconnect the power and

check that the blade carrier is free to rotate

and clean away cuttings if necessary.

How to use your mower (Fig. J & K)

Observe all the relevant warnings when

using your mower.

JWe recommend the directional method of

operation to obtain the maximum cutting

performance from your mower and to

reduce the risk of the trailing extension lead

from entering the cutting path.

•Place the bulk of the extension cable

on the lawn close to the starting point

(Fig. J, position 1).

•Hold the handle assembly with

both hands.

Your switch box incorporates a cable

restraint. To fix the cable to the restraint,

proceed as follows.

•Bring the socket end of the extension

cable from behind and connect it to

your mowers plug (not GR120C).

K•Form a loop on your extension cable

close to the coupler.

•Push the loop through the slot from the

opposite side of the restraint hook,

position the loop over the hook and

pull the cable back through the slot.

Your cable will now be restrained.

•The extension cable should now fall

away from your mower and behind the

operator, ready for use.

Warning! Do not attempt to operate your

mower with one hand - you must guide it

with both hands.

GR120_UK.P65 09-11-2000, 14:275

•To start your mower press the safety

lock-off button (24) on the switch box

(22) (Fig. A), and whilst still depressed

pull the switch lever (23) towards the

handle. Your mower will start and you

can now allow the lock-off button to be

released and commence cutting.

•Proceed down the cutting area as

shown in Fig. Ja, working from position

1 towards position 2 and, on reaching

position 2, turn to the right and proceed

towards position 3. Continue to the end

of the cutting area, turn to the left,

and proceed towards position 4.

Continue in the same manner as shown

in Fig. Ja, always working away from

the cable. Do not adopt the method as

shown in Fig. Jb, working towards the

cable, as this is dangerous practice.

Your mower will continue to operate whilst

you are depressing the switch lever. To

stop your mower release the switch lever.

When you have finished using your mower

we recommend that you clean all debris

from it before putting it away. Refer to the

“Care and maintenance” section.

Note: To obtain the best results cut your

lawn or grassed area regularly and do not

cut when the grass is wet.

•When cutting over the edge of your

lawn, press downwards on the handle

to stop the overhanging front wheels

dropping over the edge.

•To prolong the effective cutting life of

your blades, clear the lawn area of any

loose debris and stones.

•If, when using the plastic blades, a

blade comes in contact with an object

such as a large stone, the blade is

designed to break safely.

•If this occurs, disconnect from the

electrical supply, remove the remainder

of the broken blade and fit a new one.

If only one blade needs to be

exchanged, compare the length of the

new blade with the remaining blade and

if there is an excessive difference, fit two

new blades.

•If your mower is abnormally noisy

and vibrates, then it is probably due

to one blade being shorter than the

other. New blades are available from

Black & Decker service agents.

Handy hints

•On long grass, above 10cm (4 inches), use two

cuts to get a close finish. We recommend that

the first cut should be taken with the blade set

at maximum height of cut and the second

taken with it set at medium or close. This will

prove to be easier and give a better overall

finish to your lawn.

Care and maintenance

The advice given in this section covers the

general care and maintenance of the main

body of your mower. Advice relating to the

blades is given in “Maintenance of blades”.

Warning! Do not use an extension cable

which shows signs of damage. Fit a new

cable completely - do not make any

permanent or temporary repairs.

•Use the plastic blade system for

maintaining your lawn. Do not use it for

any heavy work.

•Always keep your mower clean and free

from grass cuttings, especially the

underside of the cutter deck and the air

vents.

•Check all electrical cables at regular

intervals, looking for signs of wear,

abrasion or other damage.

•At the end of each cutting session we

recommend that the build up of grass

on the underside of the cutter cover is

removed using a blunt scraper.

•Clean all plastic components with a

damp cloth.

Caution: Do not use solvents or cleaning

fluids as these may damage the plastic

components of your mower.

Fault finding

If your mower does not operate correctly,

use the table below to locate the problem.

Warning! Always disconnect your mower

from the electrical supply before carrying

out any inspection.

Symptoms Possible cause Remedy

Motor buzzes Blade jammed. Disconnect from

but blade does the electrical

not move. supply.

Remove

obstruction from

the blade.

GR120_UK.P65 09-11-2000, 14:276

ENGLISH

Symptoms Possible cause Remedy

No noise and Faulty electrical Disconnect from

blade does connection. the electrical

not move. supply.

Plug your mower

. into an alternative

compatible

electrical supply.

Fit a new fuse.

Re-tighten and

check all electrical

connections in

extension cables.

Re-set RCD in

accordance

with instructions.

What to do if your mower needs

repair

For after sales service please refer to the section

‘Lawnmowers & Garden’ within your local

Yellow Pages.

Unwanted products and the

environment

Should you find one day that your mower

needs replacement, or is of no further

use to you, think of the protection of the

environment. Black & Decker service

agents will accept your old mower and will

dispose of it in an environmentally safe way.

Black & Decker lawn and garden

guarantee

This guarantee provides 36 months parts cover

and 12 months labour (UK), 24 months parts

cover and labour (Australia and New Zealand).

In all cases proof of purchase will be required.

lf your Black & Decker mower becomes defective,

within the guarantee period, due to faulty materials

and workmanship, we guarantee to either replace

all defective parts, or at our discretion, replace your

mower free of charge, provided that:

•Your mower is returned to one of our authorised

repair agents with evidence of purchase.

•Your mower has been used within the

parameters of its consumer classification.

•Your mower has not been used for hire purposes.

•Repairs have not been attempted by anyone

other than our authorised repair agents.

•The failure represents normal wear and tear.

This guarantee is offered as an extra benefit and is

additional to your statutory rights.

Our guarantee policy

Failures due to the following are not covered:

•Replacing worn or damaged blades, nylon line

and chains, or cables damaged during storage

or use. These are regarded as replacement

items which wear during normal usage.

•Failures as a result of sudden impact or

obvious abuse.

•Failures due to usage not in accordance with

instructions and recommendations contained in

this manual.

The use of other than genuine Black & Decker

accessories and parts may damage or reduce the

performance of your Black & Decker mower and

may render the guarantee void.

Black & Decker after sales service

(UK, Australia and New Zealand

only)

Black & Decker offers a nationwide network of

authorised service agents. The use of other than

genuine Black & Decker accessories and parts may

damage or reduce the performance of your

Black & Decker product and may also endanger

the user. The terms and conditions of the warranty

may also be effected.

It is our aim that all Black & Decker customers

should be totally satisfied with their Black & Decker

product and after sales service, if help or advice is

needed please contact a local Black & Decker

authorised repair agent who will be happy to help.

Full details of our after sales service can be

obtained from any of our Black & Decker

authorised repair agents.

Other Black & Decker products

(UK only)

Black & Decker has a full range of outdoor power

tools that make life easy in the garden. If you would

like further information on other products, please

contact the Black & Decker Service Information

Centre at the address towards the back of this

manual, or contact your Black & Decker stockist.

Lawnmowers String trimmers

Chainsaws Lawnrakers

Compost shredders Leafbusters

Blade trimmers Cordless brooms

Cordless trimsaws Cordless shrubbers

Cordless shears Hedgetrimmers

GR120_UK.P65 09-11-2000, 14:277

ENGLISH

EC Declaration of Conformity

We declare that unit:

GR120

conforms to 98/37/EC, 89/336/EC, 73/23/EC,

EN60335, EN55014, EN61000

A weighted sound pressure 72dB (A)

A weighted sound power 92dB (A)

Hand/arm weighted vibration <2.5m/s2

Brian Cooke

Director of Engineering

Black & Decker Ltd, Spennymoor, County Durham

DL16 6JG United Kingdom

GR120_UK.P65 09-11-2000, 14:278

836

4349

25 24

13 27 29

51 52

31 - 10 - 2000

E13058/375813-36

www.2helpU.com

GR120C

TYP.

GR120_UK.P65 09-11-2000, 14:279

375813 - 36

Australia DEWALT Industrial Power Tool Company Tel. 03 9895 9200

7 Clarice Road Fax 03 9899 7465

Box Hill, Victoria 3128

New Zealand Black & Decker Tel. 09 579 7600

81 Hugo Johnson Drive Fax 09 579 8200

Penrose, Auckland, New Zealand

South Africa Black & Decker South Africa (Pty) Ltd Tel. (011) 653-1400

Physical address: Fax (011) 653-1499

146 Lechwe Street

Corporate park

Randjiesfontein, Midrand

Postal address:

Postnet Suite 107, Private Bag X65

Halfway House 1685

United Kingdom Black & Decker Tel. 01753 511234

210 Bath Road Fax 01753 551155

Slough, Berkshire SL1 3YD Helpline 01753 574277

GR120_UK.P65 09-11-2000, 14:2710

Inhaltsverzeichnis

Andere Black & Decker Rasenmäher Handbücher

Black & Decker

Black & Decker MM875 Bedienungsanleitung

Black & Decker

Black & Decker GR3000 Bedienungsanleitung

Black & Decker

Black & Decker 90514757 Bedienungsanleitung

Black & Decker

Black & Decker GRC450 Bedienungsanleitung

Black & Decker

Black & Decker 8060 Bedienungsanleitung

Black & Decker

Black & Decker MM275 Bedienungsanleitung

Black & Decker

Black & Decker 8008 Bedienungsanleitung

Black & Decker

Black & Decker 8119 Bedienungsanleitung

Black & Decker

Black & Decker le750 Bedienungsanleitung

Black & Decker

Black & Decker CMM1200 Bedienungsanleitung

Black & Decker

Black & Decker GR233 Bedienungsanleitung

Black & Decker

Black & Decker 8214 Bedienungsanleitung

Black & Decker

Black & Decker MTD100 Bedienungsanleitung

Black & Decker

Black & Decker GX530 Bedienungsanleitung

Black & Decker

Black & Decker EMax34i Betriebsanleitung

Black & Decker

Black & Decker BEMW213 Bedienungsanleitung

Black & Decker

Black & Decker GR230 Bedienungsanleitung

Black & Decker

Black & Decker SPCM1936 Bedienungsanleitung

Black & Decker

Black & Decker gr292 Bedienungsanleitung

Black & Decker

Black & Decker GR290 Bedienungsanleitung

Black & Decker

Black & Decker LM175 Bedienungsanleitung

Black & Decker

Black & Decker CLMA4825L2 Bedienungsanleitung

Black & Decker

Black & Decker EMax34s Bedienungsanleitung

Black & Decker

Black & Decker GX295 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung