Black & Decker Powerful Solutions AS36LN Bedienungsanleitung

English 4

INDONESIA 16

AS36LN

This manual is applicable for A9, KR, B1 and JP

90581821

➇

➃

➆

➄

➅

➂

➉

➈

➁

➀

2F1F

1G3F

➆

ENGLISH

3.6V Li-ion Screwdriver

AS36LN

Technical Data

Cordless Screwdriver AS36LN

Voltage VDC 3.6

No Load Speed RPM 180

Max. Torque Nm 4.8

Bit Holder mm (Hex) 6.35

Weight kg 0.5

Battery

Voltage V 3.6

Type Li-ion

Capacity Ah 1.1

Charger

Approx. Charging Time Hour 6 (fully charged)

Weight kg 0.4

Intended Use

Your Black & Decker compact screwdriver has been designed for screwdriving applications.

The tool is intended for consumer use only.

Your Black & Decker charger has been designed for charging Black & Decker batteries of

the type supplied with this tool.

Safety Instructions

When using power tools, always observe the safety regulations applicable in your

country to reduce the risk of fire, electric shock, personal injury and material damage.

Read the following safety instructions before attempting to operate this product. Keep

these instructions in a safe place!

The following symbols are used throughout this manual:

Denotes risk of personal injury, loss of life or damage to the tool in case of non-

observance of the instructions in this manual.

ENGLISH

Denotes risk of electric shock.

Fire hazard.

1. Keep work area clean. Cluttered areas and benches can cause accidents.

2. Consider work area environment. Do not expose power tool to humidity. Keep work

area well lit (250-300 Lux). Do not use power tools in the presence of inflammable liquids

or gases.

3. Keep children away. Do not let children come into contact with the tool or extension

cord. Keep all people away from the work area.

4. Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving

parts. Preferably wear rubber gloves and non-slip footwear when working outdoors.

Wear protective hair covering to keep long hair out of the way. When working outdoors,

preferably wear suitable gloves and non-slip footwear.

5. Personal protection. Always use safety glasses. Everyday eyeglasses only have impact

resistant lenses, they are not safety glasses. Use a face or dust mask whenever the

operations may produce dust or flying particles. If these particles might be considerably

hot, also wear a heat-resistant apron. Wear ear protection whenever the sound level

seems uncomfortable, i.e. if the sound pressure stated in this manual exceeds 85 dB(A).

6. Do not overreach. Keep proper footing and balance at all times.

7. Stay alert. Watch what you are doing. Use common sense. Do not operate the tool

when you are tired.

8. Secure workpiece. Use clamps or a vice to hold the workpiece. It is safer and it frees

both hands to operate the tool.

9. Remove adjusting keys and wrenches. Always check that adjusting keys and

wrenches are removed from the tool before switching on.

10. Use appropriate tool. The intended use is laid down in this instruction manual. Do not

force small tools or attachments to do the job of a heavy-duty tool. The tool will do the

job better and safer at the rate for which it was intended. Do not force the tool.

Warning! The use of any accessory or attachment or performance of any operation

with this tool, other than those recommended in this instruction manual may present a

risk of personal injury.

11. Check for damaged parts. Before using the tool, carefully check it for damage

to ensure that it will operate properly and perform its intended function. Check for

misalignment and seizure of moving parts, breakage of parts and any other conditions

that may affect its operation. Have damaged guards or other defective parts repaired or

replaced as instructed. Do not use the tool if the switch is defective. Have any damaged

or defective parts replaced by an authorized repair agent. Never attempt any repairs

yourself.

ENGLISH

12. Avoid unintentional starting. Do not carry the plugged-in tool with a finger on the

switch. Be sure that the switch is released when plugging in.

13. Do not abuse cord. Never carry the tool by its cord or yank it to disconnect from the

socket. Keep the cord away from heat, oil and sharp edges.

14. Store idle tools. When not in use, power tools must be stored in a dry place and locked

up securely, out of reach of children.

15. Maintain tools with care. Keep the tools in good condition and clean for better and

safer performance. Follow the instructions for maintenance and changing accessories.

Inspect the tool cords at regular intervals and, if damaged, have them repaired by an

authorized repair agent. Inspect the extension cords periodically and replace them if

damaged. Keep all controls dry, clean and free from oil and grease.

16. Have your tool repaired by an authorized repair agent. This power tool is in

accordance with the relevant safety regulations. To avoid danger, electric appliances

must only be repaired by qualified technicians using original spare parts.

Additional Safety Instructions for Batteries and Chargers

Batteries

17. Never attempt to open for any reason.

18. Do not store in locations where the temperature may exceed 40ºC.

19. Charge only at ambient temperatures between 4ºC and 40ºC.

20. Charge only using the charger provided with the tool (see technical data).

21. When disposing of batteries, follow the instructions given in the section

“Protecting the environment”.

22. Leaks from battery cells can occur under extreme conditions. The battery fluid,

a 25-30% solution of potassium hydroxide, can be harmful. In case of skin contact:: (a)

wash quickly with soap and water; or (b) neutralize with a mild acid such as lemon juice

or vinegar. If the liquid gets into the eyes, flush them immediately with clean water for a

minimum of 10 minutes. Seek medical attention.

23. Fire hazard! Avoid short-circulating the contacts of a detached battery.

24. Do not incinerate the battery.

Chargers

25. Use your Black & Decker charger only to charge the battery in the tool with which it was

supplied. Other batteries could burst, causing personal injury and damage.

26. Never attempt to charge non-rechargeable batteries.

ENGLISH

27. Have defective cords replaced immediately.

28. Do not expose to water.

29. Do not open the charger.

30. Do not probe the charger.

31. The charger is intended for indoor use only.

Specific Safety Rules

32. When fitting and changing accessories, always use the instructions supplied with the

accessory.

33. Should your screwdriver develop a fault, do not try to fix it yourself, but take it to one of

our authorized repair agents.

34. Warning: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work

with approved safety equipment, such as those dust masks that are specially designed

to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

ENGLISH

Labels on your tool

They may include the following symbols.

V ............. volts

A ............. Amperes

Hz ............. Hertz

W ............. Watts

Min. ............. Minutes

............. Alternating current

............. Direct current

no............. No load speed

............. Class II Construction

............. Earthing terminal

............. Safety alert symbol

.../min ............. Revolutions or reciprocation per minute

.../bpm ............. Beats per minute

Save these instructions!

Electrical safety

Your charger is double insulated; therefore no earth wire is required. Always check

that the mains voltage corresponds to the voltage on the rating plate. Never attempt to

replace the charger unit with a regular mains plug.

Using an Extension Cable

An extension cable should not be used unless absolutely necessary. Use of an improper

extension cable could result in a risk of fire and electric shock. If an extension cable must be

used, use only those that are approved by the country’s Electrical Authority. Make sure that

extension cord is in good condition before using. Always use the cord that is suitable for the

power input of your charger (see technical data on name plate).

When using a cable reel, always unwind the cable completely.

ENGLISH

Fig. A

1. On/off switch

2. Forward/reverse slider

3. Forward/reverse window

4. Bit holder

5. LED light

6. Mode selector / torque adjustment collar

7. Screw holder

8. Charger

9. Charging base

10. Charging indicator

11. Bit storage

Assembly

Fitting the charging base to the wall (fig. A & B)

The charging base (9) can be placed on a worktop or fitted to the wall to provide a

convenient storage and charging point for the tool. Screws and wall anchors are not

included.

Drive screws in the wall with the same distance apart as the slots (13) on the back of the

charging base (9).

The distance between the slots must be 75 mm.

Slide the charging base over the screws to fit the base to the wall.

Plug in the charger (8).

Place the tool on the charging base making sure the charging indicator (10) lights up.

Warning! Avoid damaging the power cord when mounting the charging base to the wall.

Fitting and removing a drill bit or a screwdriver bit (fig. C)

This tool uses screwdriver bits and drill bits with a 6.35 mm (1/4”) hexagonal shank.

To fit a bit, insert the bit shaft into the bit holder (4).

To remove a bit, pull the bit shaft out of the bit holder (4).

◆

ENGLISH

Use

Warning! Let the tool work at its own pace. Do not overload.

Before first use, the battery must be charged for at least 9 hours.

Charging the battery (fig. A)

Place the tool on the charging base (9).

Plug in the charger (8).

Leave the tool connected to the charger for 6 hours.

The red light illuminates when the unit is on charge and will stay red as long as there is

power to the charger. The red light will not go off to indicate a full charge.

The charger may hum and become warm while charging; this is normal and does not

indicate a problem.

Warning! Do not charge the battery at ambient temperatures below 4 °C or above 40 °C.

Selecting the direction of rotation (fig. D)

For drilling and for tightening screws, use forward (clockwise) rotation. For loosening screws

or removing a jammed drill bit, use reverse (counterclockwise) rotation.

The forward/reverse window (3) displays the rotation direction with an arrow.

To select forward rotation, push the forward/reverse slider (2) to the forward position.

To select reverse rotation, push the forward/reverse slider (2) to the rearward position.

To lock the tool, set the forward/reverse slider into the centre position.

Selecting the torque (fig. E)

This tool is fitted with a collar to set the torque for various screwdriving and drilling

applications. Large screws and hard workpiece materials require a higher torque setting than

small screws and soft workpiece materials. The collar has a range of 6 settings to suit your

application.

To set the torque, rotate the torque adjustment collar (6) clockwise or counterclockwise.

For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as follows:

- Set the collar (6) to the lowest torque setting.

- Tighten the first screw.

◆

Andere Handbücher für Powerful Solutions AS36LN

Inhaltsverzeichnis

Sprachen:

Andere Black & Decker Akkuschrauber Handbücher

Black & Decker

Black & Decker KC36LN Bedienungsanleitung

Black & Decker

Black & Decker KC360NM Bedienungsanleitung

Black & Decker

Black & Decker Pivot Driver PP360 Bedienungsanleitung

Black & Decker

Black & Decker MT350 Bedienungsanleitung

Black & Decker

Black & Decker cp14ln Bedienungsanleitung

Black & Decker

Black & Decker KC9006 Bedienungsanleitung

Black & Decker

Black & Decker KC9024 Bedienungsanleitung

Black & Decker

Black & Decker KC4815 Bedienungsanleitung

Black & Decker

Black & Decker Pivot Driver PP360 Bedienungsanleitung

Black & Decker

Black & Decker SCRUGUN 2020-10 Bedienungsanleitung

Black & Decker

Black & Decker EPC14 Bedienungsanleitung

Black & Decker

Black & Decker Pivot Driver PP360LN-XE Bedienungsanleitung

Black & Decker

Black & Decker 90530144 Bedienungsanleitung

Black & Decker

Black & Decker KC600H Bedienungsanleitung

Black & Decker

Black & Decker 9078 Bedienungsanleitung

Black & Decker

Black & Decker BDSG500 Linea PRO Bedienungsanleitung

Black & Decker

Black & Decker BDCT108 Bedienungsanleitung

Black & Decker

Black & Decker BDCD8C Bedienungsanleitung

Black & Decker

Black & Decker 9078 Bedienungsanleitung

Black & Decker

Black & Decker KC3610 Bedienungsanleitung

Black & Decker

Black & Decker Scrugun 2035-740-2 Bedienungsanleitung

Black & Decker

Black & Decker LI3100 Bedienungsanleitung

Black & Decker

Black & Decker ASL146 Bedienungsanleitung

Black & Decker

Black & Decker EGBL108 Bedienungsanleitung

Beliebte Akkuschrauber Handbücher anderer Marken

Makita

Makita DFT085F Bedienungsanleitung

Parkside

Parkside 345138 2004 Bedienungsanleitung

Makita

Makita DFL650F Bedienungsanleitung

AEG

AEG BST 18BLX2-0 Bedienungsanleitung

Ingersoll-Rand

Ingersoll-Rand D5000 Series Bedienungsanleitung

BGS technic

BGS technic 956 Bedienungsanleitung

Hilti

Hilti SD 6000 Bedienungsanleitung

Parkside

Parkside PEPS 3 A1 Bedienungsanleitung

Festool

Festool TI 15 Bedienungsanleitung

Makita

Makita DWT190 Bedienungsanleitung

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Bedienungsanleitung

Skil

Skil 2346 Montageanleitung

DeWalt

DeWalt XR LI-ION DCD931 Bedienungsanleitung

Festool

Festool DWC 18-2500 Bedienungsanleitung

EINHELL

EINHELL TE-CD 12/1 Li Series Bedienungsanleitung

Makita

Makita BFT043F Bedienungsanleitung

Stanley

Stanley SCD2 Bedienungsanleitung

Atlas Copco

Atlas Copco LUM12 SR Merkblatt