Black & Decker BDS202 Bedienungsanleitung

www.blackanddecker.eu

English 5

Deutsch 12

Français 20

Italiano 27

Nederlands 37

Español 41

Português 48

Svenska 55

Norsk 62

Dansk 69

Suomi 76

Ελληνικά 83

5 6

ENGLISH

Intended use

This Black & Decker tool has been designed to help locate live wires operating at mains

voltage (230 VAC) and metal pipes covered by wall boards.

This tool is intended for consumer use only.

Safety instructions

 Warning! When using battery-powered tools, basic safety precautions, including the

following, should always be followed to reduce the risk of ﬁre, leaking batteries,

personal injury and material damage.

 Read all of this manual carefully before operating the tool.

 Retain this manual for future reference.

Keep work area clean

Cluttered areas and benches can cause accidents.

Consider work area environment

Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the work

area well lit. Do not use the tool where there is a risk of causing ﬁre or explosion, e.g. in the

presence of ﬂammable liquids and gases.

Keep children away

Do not allow children, visitors or animals to come near the work area or to touch the tool.

Do not overreach

Keep proper footing and balance at all times.

Stay alert

Watch what you are doing. Use common sense. Do not operate the tool when you are tired.

Use appropriate tool

The intended use is described in this instruction manual.

Warning! The use of any accessory or attachment or performance of any operation with this

tool other than those recommended in this instruction manual may present a risk of personal

injury.

Check for damaged parts

Before use, carefully check the tool for damage. Ensure that the tool will operate properly

and perform its intended function. Do not use the tool if any part is damaged or defective.

Store idle tools

When not in use, tools should be stored in a dry, locked up or high place, out of reach of children.

ENGLISH

Repairs

This tool complies with relevant safety requirements. Repairs should only be carried out by

qualiﬁed persons using original spare parts; otherwise this may result in considerable danger

to the user.

Additional safety instructions for non-rechargeable batteries

Warning! Batteries can explode or leak, and can cause injury or ﬁre. Observe the

instructions as described below.

Warning! Ensure the switch is in the off position before inserting the batteries. Inserting

batteries into power tools and appliances that have the switch on invites accidents.

Warning! Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

 Carefully follow all instructions and warnings on the battery label and package.

 Always place batteries correctly according to the polarity (+ and -) as marked on the

battery and the product.

 Do not short-circuit the battery terminals.

 Do not attempt to charge non-rechargeable batteries.

 Do not mix old and new batteries. Replace all of the batteries at the same time with new

batteries of the same brand and type.

 Keep batteries out of reach of children.

 Remove batteries if the product will not be used for several months.

 Never attempt to open for any reason.

 Do not store in locations where the temperature may exceed 40 °C.

 When disposing of batteries, follow the instructions given in the section "Protecting the

environment".

 Do not incinerate the batteries.

Additional safety instructions for pipe and wire detectors

 Do not use the tool to detect AC voltage in uninsulated, exposed or free wires.

 Do not use the tool as a substitute for a voltmeter.

 Be aware that the tool may not always properly detect all pipes and wires. The following

conditions can cause inaccurate results:

- Low battery

- Thick walls with thin pipes or wires

- Very thick walls

- Very deep wires or pipes

ENGLISH

- Walls covered with metal

- Very humid conditions

- Shielded cables

 Before use, always test the tool by detecting a known pipe or wire.

 If in doubt contact a qualiﬁed service agent.

Warning! This tool will not detect wires in circuits isolated from the mains supply, cables

operating at direct current (DC) or wires used for telecommunication or computer systems.

Hidden wires (e.g. wall lights) may not be detected when switches are in the off position.

Warning! This tool will not detect pipes of any other material than metal.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must read the instruction manual.

Features

1. On/off switch

2. LCD screen (metal ﬁnder)

3. LED indicator (AC wire)

Assembly

Fitting the battery (ﬁg. A)

 Slide the battery cover (4) off the tool.

 Insert the battery making sure to match (+) and (-) terminals inside the battery

compartment with the battery.

 Reﬁt the cover and let it click into place.

Use

Warning! If the equipment is used in a manner not speciﬁed by the manufacturer, the

protection provided by the equipment may be impaired.

Using the metal ﬁnder function (ﬁg. B, C & D2)

You can use this function (6) to ﬁnd metal pipes through drywall boards up to 25 mm thick.

 Hold the tool in the air away from the wall and any metal objects.

 Press the on/off switch (1).

ENGLISH

The LCD screen (2) will light up and the buzzer will sound once while the tool is calibrating.

After calibration is completed:

 Keep the on/off switch (1) depressed.

The metal detection indicator symbol (6) is indicated on the display.

 Place the tool ﬂat against the wall as shown.

 Slowly slide the tool in a horizontal direction over the surface without lifting off or

changing the applied pressure (ﬁg. C). Make sure not to tilt or lift the tool.

When 3 scanner bars (7) on the LCD screen (2) start to climb this indicates you are

apporaching a metal object.

 Continue scanning the surface.

Upon close proximity to a metal object, the bars will reach the top and then fall. When no

bars are displayed, keep the on/off switch depressed and reverse the movement to get

accurate results. 3 bars reaching the top indicate the location of a metal object (ﬁg. D2).

 After detecting the work area repeat the testing procedure to conﬁrm the operation of the

unit.

Note:

 Please keep ﬁngers away from the area of detection as this may interfere with the results.

 Wall must be ﬂat to get the most accurate results.

Using the wire detector function (ﬁg. D1)

You can use this function to ﬁnd live wires to 100 mm in depth. The function works

continuously in all modes.

Warning! Test the unit on a known AC current before use.

 Make sure the unit is away from the area being scanned and any other AC current

source.

 Press the on/off switch (1).

The red LED indicator (3) will light up and the buzzer will sound once while the tool is

calibrating. After calibration is completed:

 Keep the on/off switch (1) depressed.

 Move the tool slowly and smoothly across the surface, approaching from different

directions.

When an AC source is located, the red LED indicator (3) will blink.

 After detecting the work area repeat the testing procedure to conﬁrm the operation of the

unit.

Note: Static charge may interfere with detection on both sides of the wire, resulting in limited

accuracy.

ENGLISH

Battery indicator (ﬁg. B)

The LCD screen displays a battery symbol (5) that indicates the present condition of the

battery.

 Replace the battery on time.

Protecting the environment

Z Separate collection. This product must not be disposed of with normal household

waste.

Should you ﬁnd one day that your Black & Decker product needs replacement, or if it is of no

further use to you, do not dispose of it with household waste. Make this product available for

separate collection.

z Separate collection of used products and packaging allows materials to be

recycled and used again. Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the

household, at municipal waste sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and recycling of Black & Decker products

once they have reached the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by contacting your local

Black & Decker ofﬁce at the address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our after-sales service and

contacts are available on the Internet at: www.2helpU.com

Battery

At the end of their useful life, discard batteries with due care for our environment.

 Remove the battery as described above.

ENGLISH

 Place the battery in a suitable packaging to ensure that the terminals cannot be

short-circuited.

 Take the battery to a local recycling station.

Technical data

BDS202

Voltage V 9

Battery size 6LR61

Max. scanning depth*

Ferrous metals mm 45

Other metals mm 25

AC live wires mm 100

Operating temperature °C 0 - 40

Weight kg 0.25

* Detection depth capabilities may vary depending on material, size of objects as well as

material and condition of structure. Environment condition: indoor use, related humidity

95% maximum.

Guarantee

Black & Decker is conﬁdent of the quality of its products and offers an outstanding

guarantee. This guarantee statement is in addition to and in no way prejudices your statutory

rights. The guarantee is valid within the territories of the Member States of the European

Union and the European Free Trade Area.

If a Black & Decker product becomes defective due to faulty materials, workmanship or lack

of conformity, within 24 months from the date of purchase, Black & Decker guarantees to

replace defective parts, repair products subjected to fair wear and tear or replace such

products to ensure minimum inconvenience to the customer unless:

 The product has been used for trade, professional or hire purposes;

 The product has been subjected to misuse or neglect;

 The product has sustained damage through foreign objects, substances or accidents;

 Repairs have been attempted by persons other than authorised repair agents or

Black & Decker service staff.

Inhaltsverzeichnis

Sprachen:

Andere Black & Decker Werkzeuge Handbücher

Black & Decker

Black & Decker RT 650 Bedienungsanleitung

Black & Decker

Black & Decker 79-016 Bedienungsanleitung

Black & Decker

Black & Decker WP1300K Bedienungsanleitung

Black & Decker

Black & Decker KD975 Bedienungsanleitung

Black & Decker

Black & Decker ATM100 Bedienungsanleitung

Black & Decker

Black & Decker BD1800JS Bedienungsanleitung

Black & Decker

Black & Decker BDCMTO Bedienungsanleitung

Black & Decker

Black & Decker BCL101 Bedienungsanleitung

Black & Decker

Black & Decker WM1000 Bedienungsanleitung

Black & Decker

Black & Decker Matrix BDCMTO-XE Bedienungsanleitung

Black & Decker

Black & Decker EXTENDER ATM100 Bedienungsanleitung

Black & Decker

Black & Decker PROJECT PAL 71-045 Bedienungsanleitung

Black & Decker

Black & Decker W006B Bedienungsanleitung

Black & Decker

Black & Decker RT 650 Bedienungsanleitung

Black & Decker

Black & Decker 48365 Bedienungsanleitung

Black & Decker

Black & Decker EasyEdge BDPE200-AR Bedienungsanleitung

Black & Decker

Black & Decker MT1203B Bedienungsanleitung

Black & Decker

Black & Decker BDL190S-XE Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung