Black Box LB510A Bedienungsanleitung

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

G.SHDSL NTU

DECEMBER 2006

LB510A

G.SHDSL NTU

TRADEMARKS USED IN THIS MANUAL

All applied-for and registered trademarks are the property of their respective owners.

• The LB510A contains no user serviceable parts. The equip-

ment shall be returned to Black Box for repairs, or

repaired by qualiﬁed service personnel.

• An approved external power supply that incorporates a

disconnect device shall be used and positioned within easy

reach of the operator.

• For AC powered units, the power cable used to connect the

power supply shall meet all applicable standards for the

country in which it is to be installed, and be connected to a

wall outlet which has earth ground.

• Hazardous network voltages are present in WAN ports

regardless of whether power to the unit is ON or OFF. To

avoid electric shock, use caution when near WAN ports.

When detaching the cables, detach the end away from the

NTU ﬁrst.

• Do not work on the system or connect or disconnect cables

during periods of lightning activity.

WARNING

G.SHDSL NTU

1. Power up the NTU

Your NTU comes with an externalAC adaptor with detachable power cord.

1.1 AC power-up

1. Connect female plug of the AC power cord to the AC adaptor provided.

2. Connect the barrel-type connector of the AC adaptor to the barrel-type

power jack on the LB510A.

3. Insert the male plug of the AC power cord into an AC power outlet (100–

240 VAC)

1.2 Power-up indication

The

Power

and

100M Ethernet

LEDs are lit while the LB510A is powering up.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

WARNING

G.SHDSL NTU

2. Conﬁgure the IP address

The LB510A is shipped with a factory-conﬁgured IP address assigned to the

Ethernet

LAN port (green outline). The address is

192.168.200.10/24

. In most

cases, you must change the address to be on the same subnet as your PC, as

described in the procedures below. If you are not sure which IP address to use for

your installation, contact your network administrator.

2.3 Connect a PC and log in

1. Using the included combination RS232/Ethernet cable and DB9-RJ45

adapter, connect a PC’s serial port to the LB510A’s

Console

port (red out-

line) (see Figure 1).

Figure 1.

Connecting the LB510A to the PC’s serial port

2. Start a HyperTerminal session on the PC using the settings:

9600 bps, 8 data bits, no parity, 1 stop bit, no ﬂow control

3. Log in to the LB510A using the factory-default login (

superuser

) and pass-

word (

superuser

Password: *********

MDI-X

LineEthernet

Power Console

Connect to Console port

Serial port

PC with

terminal emulator

G.SHDSL NTU

2.4 Modify the IP address

1. Display current IP interface settings for the LB510A

Ethernet

LAN port.

ip list interfaces <enter>

IP Interfaces:

ID | Name | IP Address | DHCP | Transport

---|------|----------------|----------|--------------

1 | ip1 | 192.168.200.10 | disabled | <BRIDGE>

----------------------------------------------------

2. Modify the IP address for the LAN port according to your network require-

ments.

ip set interface ip1 ipaddress 10.10.4.10 255.255.255.0

Note

The above IP address (

10.10.4.10/24)

is only an example.You must choose

an IP address on the same subnet as your PC

3. Verify the new address is correct and save it in system boot memory.

ip list interfaces <enter>

system config save <enter>

G.SHDSL NTU

3. Connect to the local IP network

Now you can connect the LB510A to your local IP network and complete the

remaining conﬁguration from your PC using a standard web browser.

Connect the LB510A’s

Ethernet

port (green) to the same Ethernet segment as

your PC (see Figure 2). The front-panel

Ethernet Link

LED should turn on. If it

does not, press the rear-panel MDI-X switch so that the

Ethernet Link

LED illu-

minates.

You can check the connection with the ping command. For example shown in

Figure 2, you would ping 10.10.4.10 from a PC on the IP network.

Figure 2.

Connecting the LB510A to the local IP network

MDI-X

LineEthernet

Power Console

Connect to Ethernet port Ethernet port

MDI-X switch

G.SHDSL NTU

4. Log onto the web management interface

You will now access the web management graphical user interface (GUI) to con-

ﬁgure the LB510A using a standard web browser (such as Netscape browser or

Internet Explorer).

1. At your PC, open a web browser and enter the IP address you assigned to

the LB510A’s Ethernet LAN port in step 2 of section “Modify the IP

address” on page 5. (In this example, 10.10.4.10.)

2. Log in to the web management home page using the username

superuser

and the password

superuser.

Figure 3.

Web management home page

G.SHDSL NTU

5. Connect the G.SHDSL Port

1. Obtain single-twisted-pair cable with an RJ-11 plug connector at each end.

2. Plug one end of the cable into the (yellow) RJ-11 socket (labelled

Line)

the LB510A.

3. Plug the other end of the cable into the RJ-11 wall socket that provides your

G.SHDSL service.

4. Go to

G.SHDSL > Conﬁguration

to conﬁgure the DSL port parameters.

Note

If two LB510As are connected back-to-back, one must be conﬁgured as

Remote

, the other as

Central

5. The

WAN Link

LED will ﬂash while in the process of establishing a link.

The LED will be on constantly once a valid DSL connection is established.

6. Additional Information

Refer to the

LB510A G.SHDSL NTU Getting Started Guide

located on the CD-

ROM shipped with your LB510A for detailed information about:

•

Installing, conﬁguring, operating, and troubleshooting,

•

Warranty, trademark, & compliance

G.SHDSL NTU

A. Compliance Information

A.1 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed

and used properly—that is, in strict accordance with the manufacturer's instruc-

tions—may cause interference to radio and television reception. This equipment

has been tested and found to comply with the limits for a Class A computing

device in accordance with the speciﬁcations in Subpart B of Part 15 of FCC rules,

which are designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that interference will not

occur in a particular installation. If the equipment causes interference to radio or

television reception, which can be determined by disconnecting the cables, try to

correct the interference by one or more of the following measures: moving the

computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the

computing equipment and receiver are on different branches).

A.2 EC Declaration of Conformity

Product Description:

LB510A

We certify that the apparatus identiﬁed above conforms to the requirements of

Council Directive 1999/5/EC on the approximation of the laws of the member

states relating to Radio and Telecommunication Terminal Equipment and the

mutual recognition of their conformity.

A.3 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted

by ACTA. On the bottom side of this equipment is a label that contains—among

other information—a product identiﬁer in the format US: AAAEQ##TXXXX. If

requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements

adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company

will notify you in advance that temporary discontinuance of service may be

The safety advises in the documentation accompanying the

products shall be obeyed.The conformity to the above directive

is indicated by the CE sign on the device.

G.SHDSL NTU

required. But if advance notice isn’t practical, the telephone company will notify

the customer as soon as possible. Also, you will be advised of your right to ﬁle a

complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, opera-

tions or procedures that could affect the operation of the equipment. If this hap-

pens, the telephone company will provide advance notice in order for you to

make necessary modiﬁcations to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information,

please contact our company. If the equipment is causing harm to the telephone

network, the telephone company may request that you disconnect the equipment

until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public

utility commission, public service commission or corporation commission for

information.

A.4 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Tech-

nical Speciﬁcations. This is conﬁrmed by the registration number. The abbrevia-

tion, IC, before the registration number signiﬁes that registration was performed

based on a Declaration of Conformity indicating that Industry Canada technical

speciﬁcations were met. It does not imply that Industry Canada approved the

equipment.

This Declaration of Conformity means that the equipment meets certain telecom-

munications network protective, operational and safety requirements. The

Department does not guarantee the equipment will operate to the user’s satisfac-

tion. Before installing this equipment, users should ensure that it is permissible to

be connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection. In

some cases, the company’s inside wiring associated with a single line individual

service may be extended by means of a certiﬁed connector assembly (telephone

extension cord). The customer should be aware that compliance with the above

condition may not prevent degradation of service in some situations. Repairs to

some certiﬁed equipment should be made by an authorized maintenance facility

designated by the supplier. Any repairs or alterations made by the user to this

equipment, or equipment malfunctions, may give the telecommunications com-

pany cause to request the user to disconnect the equipment. Users should ensure

for their own protection that the ground connections of the power utility, tele-

phone lines and internal metallic water pipe system, are connected together. This

protection may be particularly important in rural areas.

Andere Handbücher für LB510A

Inhaltsverzeichnis

Andere Black Box Netzwerk-Hardware Handbücher

Black Box

Black Box Balun G.703 Bedienungsanleitung

Black Box

Black Box MX550A Bedienungsanleitung

Black Box

Black Box ACR2004A Bedienungsanleitung

Black Box

Black Box MT1050A Bedienungsanleitung

Black Box

Black Box Secure Site Manager 8 Bedienungsanleitung

Black Box

Black Box RADIAN 1000 Series Bedienungsanleitung

Black Box

Black Box TS580A-R4 Bedienungsanleitung

Black Box

Black Box JPM083A Bedienungsanleitung

Black Box

Black Box TL572A Bedienungsanleitung

Black Box

Black Box MT330A Bedienungsanleitung

Black Box

Black Box TL553A-R3 Bedienungsanleitung

Black Box

Black Box Lineshare Master - 4 Bedienungsanleitung

Black Box

Black Box TS230A-R2 Bedienungsanleitung

Black Box

Black Box CSU/DSU Bedienungsanleitung

Black Box

Black Box COE-8I Bedienungsanleitung

Black Box

Black Box LB300A-R3 Bedienungsanleitung

Black Box

Black Box V.35 FOLD-ST Series Bedienungsanleitung

Black Box

Black Box FOM Line Driver-ST Bedienungsanleitung

Black Box

Black Box DT450A Bedienungsanleitung

Black Box

Black Box LWS100AE Bedienungsanleitung

Black Box

Black Box AC504A Bedienungsanleitung

Black Box

Black Box TL482A-R3 Bedienungsanleitung

Black Box

Black Box Multi Quick Check RJ-11 Bedienungsanleitung

Black Box

Black Box G.SHDSL NTU LB510A Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung