Black Box 10BASE-T MiniHub Bedienungsanleitung
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
SEPTEMBER 1995
LE2601A
10BASE-T MiniHub
RX
LINK
PORT
10BASE-T MiniHub
1234
AUI
PWR
5678
UP LINK
3
FCC STATEMENT
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A
computing device in accordance with the specifications in Subpart J of
Part 15 of FCC rules, which are designed to provide reasonable protection
against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to
cause interference, in which case the user at his own expense will be required
to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of IndustryCanada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
TRADEMARKS
UL®is a registered trademark of Underwriters Laboratories, Incorporated.
Velcro®is a registered trademark of Velcro USA, Inc.
Any other trademarks mentioned in this manual are acknowledged to be the property
of the trademark owners.
4
INSTRUCCIONES DE SEGURIDAD
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones
de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como
sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por
los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de
calor como radiadores, registros de calor, estufas u otros aparatos
(incluyendo amplificadores) que producen calor.
5
INSTRUCCIONES DE SEGURIDAD
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo
del tipo descrito en el instructivo de operación, o como se indique en
el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que
no sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos
de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo
no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos
no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro
del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio
en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
6
10BASE-T MINIHUB
Contents
Chapter Page
1. Specifications.....................................................................................................7
2. Introduction ......................................................................................................8
2.1 Inspecting the Package and Product.....................................................8
2.2 Description..............................................................................................8
2.3 Features and Benefits ...........................................................................10
3. Installation.......................................................................................................12
3.1 Table-Top or Shelf Mounting..............................................................12
3.2 Wall (or Vertical Surface) Mounting ..................................................12
3.3 Twisted Pair Segment Connection ......................................................15
3.4 Up-Link Option on Port #8 (Up-Link Switch) ...................................16
4. Operation ........................................................................................................17
5. Troubleshooting..............................................................................................18
5.1 Before Calling for Assistance ...............................................................18
5.2 When Calling for Assistance ................................................................18
5.3 Return Material Authorization (RMA) Procedure.............................19
5.4 Shipping and Packaging Information.................................................19
CHAPTER 1: Specifications
7
1. Specifications
Maximum Ethernet Segment
Lengths — UTP (Unshielded
10BASE-T): 328 ft. (100 m);
STP (Shielded 10BASE-T):
492 ft. (150 m)
Operating Environment — Ambient
Temperature: 32 to 122°F
(0 to 50°C);
Storage Temperature: -4 to 140°F
(-20 to 60°C)
Power — Powered from AUI
interface of Ethernet device
connected to AUI on hub
Size — 0.8"H x 5.0"W x 4.4"D
(1.9 x 12.7 x 11.2 cm)
Weight — 1 lb. (0.45 kg)
Standards — Ethernet V2.0, IEEE
802.3: 10BASE-T
(the Hub is a physical-layer
standard Ethernet product and
operates independently of all
software)
Connectors — (7) RJ-45 female:
(6) station ports, (1) switch-
selectable uplink/station port,
(1) DB15 male AUI port
Indicators — (17) LEDs: (8) LINK,
(8) RX, (1) PWR
Switches — (1) uplink switch on side
of unit
Performance — Data Rate: 10 Mbps,
Partitioning: Enforced after 32
consecutive collisions;
Reconnect: Occurs after 512
bits error-free transmission
8
10BASE-T MINIHUB
2. Introduction
2.2 Description
The 10BASE-T MiniHub is an 8-port
10BASE-T workplace hub in a very
compact package. It is powered from
the AUI of an Ethernet device, not
an AC supply, although an optional
one is available. It is simple to install
and use in an office or lab environ-
ment, requiring no special rack
cabinets or wiring-closet apparatus.
The MiniHub is a standard physical-
layer Ethernet product and operates
independently of all software.
The 10BASE-T MiniHub is also
well-suited for small-to-medium sized
office or lab environments (up to 9
persons) that need an independent
Ethernet network. Small indepen-
dent networks built using the Hub
are easily expanded by cascading
hubs of equal or greater capacity.
See Section 3.4 for more about the
Up-Link switched-port feature.
The 10BASE-T MiniHub’s small
size makes it very useful for
demonstration situations in confer-
ence rooms and in exhibitions where
a temporary network or network
expansion is needed. The 10BASE-T
MiniHub takes up minimal space
and requires no AC power, and is
rugged enough to be carried in a
coat pocket.
2.1 Inspecting the Package
and Product
Examine the shipping container for
obvious damage before installing
this product; notify the carrier of any
damage that you believe occurred
during shipment or delivery. Inspect
the contents of this package for any
signs of damage and make sure that
the items listed below are included:
• 10BASE-T MiniHub
• (1) pair of mounting ears
• (1) Velcro®tape section,
approximately 3 inches long
• This User’s Guide
Remove the 10BASE-T MiniHub
from the shipping container. Be sure
to keep the shipping container in
case you need to ship the unit at a
later date.
If any items are missing or
damaged, contact your supplier.
CHAPTER 2: Introduction
9
The 10BASE-T MiniHub fits easily
into the workplace environment. It
ican be mounted on a tabletop or
shelf, or, with the included Velcro®
strip, on a wall surface, or on the
back or side of a desk or cabinet. All
of the wiring connectors are in the
same place, so that wiring space is
neat and minimal.
The 10BASE-T MiniHub includes
Link and RX LEDs for each RJ-45
port, and one LED for power,
located in the upper right corner.
Since each LED is near the port it
monitors, it is easy to associate the
status LED for each of the ports with
the appropriate port.
10BASE-T
12V #AUI
10BASE-T MiniHub
PWR
AUI PORT
UP LINK
124
1RX
LINK
PORT 3
568
7
Fig. 2-1. Top View—10BASE-T MiniHub.
10
10BASE-T MINIHUB
• LEDs simplify network
installation and maintenance—
The 10BASE-T MiniHub is
equipped with a full comple-
ment of LEDs to provide status
about basic network activity.
Eight Link LEDs offer a very
simple way for operational
connections to be verified at the
end of each 10BASE-T segment.
• Low-cost, standalone 10BASE-T
connectivity—Operating in a
standalone environment as a
self-sufficient device, the
10BASE-T MiniHub offers a very
low cost method of providing
small workgroups access to a
variety of Ethernet networking
services such as file sharing,
email, printer sharing, and other
computer information.
The 10BASE-T MiniHub is used as
a standalone unit to network a local
personal multi-user system such as
shown in Figure 2-2.
2.3 Features and Benefits
• Interconnect to an existing
Ethernet network—The 10BASE-
T MiniHub provides an Up-Link
switch for port #8 to be used to
connect it into an existing
Ethernet environment (such as
the central hub for the building
or area) via 10BASE-T wiring.
• Interoperable with other
Ethernet devices—The 10BASE-
T MiniHub is completely
interoperable with other
Ethernet-compliant network
devices. Each is fully compliant
with IEEE 802.3 specifications
for 10 Mbps CSMA/CD oper-
ation. This allows the Hub to be
integrated within any standard
Ethernet network and to operate
with all standard software.
• Installation versatility—The
10BASE-T MiniHub is simple
and easy to install in almost any
office or lab location. The tiny
package is very unobtrusive.
• Robust Network Operations—
The 10BASE-T MiniHub uses the
“star” network topology and has
automatic per-port partitioning
and reconnection. A fault on
one segment is isolated from
the rest of the network, avoiding
most network downtime.
11
CHAPTER 2: Introduction
Fig. 2-2. Hub Used in a Standalone Network.
10BASE-T
12V #AUI
10BASE-T MiniHub
PWR
AUI PORT
UP LINK
124
1RX
LINK
PORT 3
568
7
PC
PCs
Laser Writer
User
Port
AUI connection
Up to 8 RJ-45 user ports are
available where only 10BASE-T
wiring is used, and full-length
Ethernet segments are supported
on all 8 segments. In this
application, the “Up-Link” switch is
in the straight-through or = position,
so that port #8 on the front of the
unit is a user port (not an up-link to
another hub).
Andere Handbücher für 10BASE-T MiniHub
2
Inhaltsverzeichnis
Andere Black Box Schalten Handbücher
Black Box
Black Box SW1020A Bedienungsanleitung
Black Box
Black Box LBH2001A-H Bedienungsanleitung
Black Box
Black Box ServSwitch Secure Plus (with USB) Bedienungsanleitung
Black Box
Black Box KV2004A Bedienungsanleitung
Black Box
Black Box LGB5028A Bedienungsanleitung
Black Box
Black Box LB9017A-R2 Bedienungsanleitung
Black Box
Black Box LGB1003A-R2 Bedienungsanleitung
Black Box
Black Box LE2650A Bedienungsanleitung
Black Box
Black Box LGB1001A Bedienungsanleitung
Black Box
Black Box KVD200-2H Bedienungsanleitung
Black Box
Black Box SW488A Bedienungsanleitung
Black Box
Black Box MT720A-232T Bedienungsanleitung
Black Box
Black Box Stackable MiniHub Le2801a Bedienungsanleitung
Black Box
Black Box LP004A Bedienungsanleitung
Black Box
Black Box CAT5 ClassWork Plus Multiloop Bedienungsanleitung
Black Box
Black Box SW930A-R2 Bedienungsanleitung
Black Box
Black Box LGT616A-JP Bedienungsanleitung
Black Box
Black Box LGB6026A Programmierhandbuch
Black Box
Black Box KV7012A Bedienungsanleitung
Black Box
Black Box LHB8050A Bedienungsanleitung
